• 한국응용과학기술학회지
• /
• 제30권3호
• /
• pp.567-574
• /
• 2013

For this research, prepared water soluble milk casein resin and waterborne polyurethane-acrylic resin. Use these resin, this article has been analyzed about change of mechanical properties by increasing amount of casein resin in polyurethane-acrylic resin on coated leather. According to measure data for solvent resistance, WPA(waterborne polyurethane-acrylic resin) resin and WPA-C1, C2, C3(samples of polyurethane-acrylic resin with milk casein resin) had good property. As known in the results, increase of casein constant did not influence to big change of hybrid resin properties. As test of tensile strength, WPA had lowest tensile characteristic(1.598 $kg_f/mm^2$) and WPA-C3 had highest tensile characteristic(1.718 $kg_f/mm^2$). Also best properties of abrasion was WPA-C3(06.021 mg.loss). In elongation case, WPA had best properties(754 %) in this experiment.

• 대한소아치과학회지
• /
• 제30권1호
• /
• pp.69-79
• /
• 2003

자가중합형 아크릴릭 레진에 polyp를 혼합하지 않은 대조군, 그리고 레진 분말에 대한 polyP(사슬길이 13과 18의 혼합물인 Calgon)의 무게비를 1%로 혼합한 polyP 1%군, 2% 혼합한 polyP 2%군 및 3% 혼합한 polyP 3%군으로 분류하여 경화시킨 후, 경화된 각각의 레진과 실험균주 S. mutans GS5, S. sobrinus 6715, S. gordonii G9B및 Challis, 그리고 P. gingivalis 2561과 Candida albicans ATCC90027을 대상으로 레진표면에 대한 미생물들의 부착의 정도, 성장 억제효과 및 접촉각의 변화를 관찰하여 그 결과로 미루어 아크릴릭 레진에 포함된 polyP는 구강 미생물에 대해 직접적으로 강한 항균 효과를 나타내지는 않는 것으로 판단되나 미생물의 부착 특히 우식원인균인 mutans streptococci의 부착을 방해하는 것으로 가늠되며, 이는 polyP의 첨가에 의한 아크릴릭 레진 표면에서 일어난 소수성의 변화가 일부 관여하는 것으로 여겨진다. PolyP가 혼합된 아크릴릭 레진의 장착은 일반적인 아크릴릭 레진으로 제작된 가철성 장치를 장착한 후 나타날 수 있는 우식 이환의 가능성을 감소시킬 수 있는 임상적 적용 가능성을 제시하였다고 여겨진다.

• 한국응용과학기술학회지
• /
• 제28권3호
• /
• pp.359-366
• /
• 2011

In this study we experimented that how polyurethane effect to acrylic-polyurethane resin in Full-Grain leather coatings. First of all, we consummated waterborne acrylic emulsion and waterborne polyurethane resin, Than we prepared F.G leathers which were coated by acrylic resin and acrylic-polyurethane resins. According to measured data for solvent resistance, acrylic resin and acrylic-polyurethane resins had good property. Sample a(WAC) had most low strength($2.10kg_f/mm^2$) and sample d(WAC 93 : WPU 7) had most high strength($3.41kg_f/mm^2$). Also we knew that most good property of abrasion is d(47.4 mg). In elongation case, a(WAC) had most good result(645 %) in this experiment.

• 한국응용과학기술학회지
• /
• 제26권1호
• /
• pp.93-101
• /
• 2009

Antistatic acrylic resin is made from n-butyl methacrylate, methyl methacrylate, dimethyl amino ethyl methacrylate(DMAEMA), 2-ethyl hexyl methacrylate, hydroxy ethyl methacrylate, 2,2'-azobis iso-butyronitrile by synthesis. To achieve a lowest surface resistance of antistatic acrylic resin was applied to a variety of synthesis processes. The acrylic resin has been determined from the value of surface resistance and -then the antistatic acrylic resin including dimethyl amino ethyl methacrylate of the 10%, 20% and 30% is synthesized. Finally, dimethyl sulfate(DMS) on a variety of weight ratios is added to antistatic acrylic resin. When DMAEMA / DMS weight ratio is 1/1, antistatic acrylic resin isn't haze the lower the surface resistance. Compared to the traditional antistatic agent, all aspects of the physical properties is outstanding.

• The Journal of Advanced Prosthodontics
• /
• 제7권4호
• /
• pp.278-287
• /
• 2015

PURPOSE. The aim of this study was to compare the color stability, water sorption and cytotoxicity of thermoplastic acrylic resin for the non-metal clasp dentures to those of thermoplastic polyamide and conventional heat-polymerized denture base resins. MATERIALS AND METHODS. Three types of denture base resin, which are conventional heat-polymerized acrylic resin (Paladent 20), thermoplastic polyamide resin (Bio Tone), thermoplastic acrylic resin (Acrytone) were used as materials for this study. One hundred five specimens were fabricated. For the color stability test, specimens were immersed in the coffee and green tee for 1 and 8 weeks. Color change was measured by spectrometer. Water sorption was tested after 1 and 8 weeks immersion in the water. For the test of cytotoxicity, cell viability assay was measured and cell attachment was analyzed by FE-SEM. RESULTS. All types of denture base resin showed color changes after 1 and 8 weeks immersion. However, there was no significant difference between denture base resins. All specimens showed significant color changes in the coffee than green tee. In water sorption test, thermoplastic acrylic resin showed lower values than conventional heat-polymerized acrylic resin and thermoplastic polyamide resin. Three types of denture base showed low cytotoxicity in cell viability assay. Thermoplastic acrylic resin showed the similar cell attachment but more stable attachment than conventional heat-polymerized acrylic resin. CONCLUSION. Thermoplastic acrylic resin for the non-metal clasp denture showed acceptable color stability, water sorption and cytotoxicity. To verify the long stability in the mouth, additional in vitro studies are needed.

• 한국응용과학기술학회지
• /
• 제27권2호
• /
• pp.188-195
• /
• 2010

In this study, we experimented that how to synthesis waterborne urethane-acrylic hybrid resin for leather coatings. First of all, We had analyzed data by FT-IR, SEM and TGA for the machanical properties. By TGA analysis polymers showed heat distortion temperature. and by FT-IR measurement we confirmed that synthesis of urethane and acrylic. In the experiment, solvent resistance, polyurethane and acrylic grades 4-5 showed both a high. Tensile strength measured in the waterborne polyurethane > Acrylic emulsion showed strength in the order. Films were obtained by coating the water born resin on leveled surfaces and allowing them to dry at room temperature for 72hrs. After demolding, the films were kept in a desiccator to avoid moisture contant at $25^{\circ}C$ for 45hrs before the measurements. In this result, the mechanical propersies of waterborne polyurethane-acrylic hybrid resin showed that how effect to resin in leather coating between polyurethane content and acrylic content. Therefore, acrylic emulsion had most high solvent resistance glade and waterborne polyurethane had good result in abrasion test and tensile strength.

• 대한치과기공학회지
• /
• 제9권1호
• /
• pp.51-55
• /
• 1987

One of the primary advantages of acrylic resin teeth is their ability to bond chemically to the denture base resins. Fracture od acrylic resin teeth from a maxillary denture, however, is not uncommon. Bonding failures have been attributed to faulty boil-out procedures that fail to eliminate all traces of wax from the ridge lap surfaces of the teeth and to contamination of the ridge lap surface by careless application of tinfoil substitute. Attempts to increase the strength of the bond between acrylic resin teeth and heat-cured denture base resin include grinding the glossy ridge lap surface (in fluid system), painting the ridgelap surface of the teeth with monomer-polymer solution, and cutting retention grooves in the ridge lap surface of the teeth. This latter method has been tested by applying a tensile force in a labial direction to the incisal part of the lingual surface of the acrylic resin teeth. A progressive shear compressive load was applied at an angle to the lingual surface of acrylic resin teeth bonded to denture base acrylic resin. No statistically singificant advantage was derived by preparing retention grooves of different shapes in the ridgelap surface of the denture teeth.

• 한국응용과학기술학회지
• /
• 제28권2호
• /
• pp.203-212
• /
• 2011

In this study we experimented that how chain extension influences to waterborne urethane-acrylic hybrid resin for leather garment coatings. We knew that polyurethane-acrylic hybrid resins had 5 grades of solvent resistance. Tensile strength measured in the polyurethane-acrylic resin(EDA 5.37 g, 1.928 kgf/$mm^2$) had the most strong strength. Also polyurethane-acylic hybrid resin(EDA 5.37 g. 30.2 mg. loss) had better result than other hybrid resins. EDA contents higher, we obtained low elongation and low flexibility. In this result, chain extension of waterborne polyurethane-acrylic hybrid resin showed the effect in leather coating with ratio of EDA.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2021년도 가을 학술논문 발표대회
• /
• pp.162-163
• /
• 2021

To prepare the waterborne silicone acrylic resin coatings, acrylic resin was prepared by a radical polymerization. Glass transition temperature(Tg) of the acrylic copolymer was fixed at 30℃ and the contents of tertiary amine monomer(DMAEMA), were varied to be 5, 10, 15 and 20 wt%, hydroxyl monomer, and carboxyl monomer were fixed 10 wt%, and 4 wt% respectively. γ-Glycidoxypropyltrimethoxysilane(GPTMS) containing epoxy group was used for curing agents. The eqivalent ratio of amine to epoxy was 1:1. The prepared coatings exhibited excellent adhesion to various substrates, and various physical properties of the coatings were satisfactory. The gloss retension and color difference were improved at low tertiary amine concentration. The coatings containing 10wt% tertiary amine concentration have especially good weather resistant properties.

• 대한치과보철학회지
• /
• 제45권3호
• /
• pp.310-320
• /
• 2007

Statement of the problem. The fracture of acrylic resin dentures remains an unsolved problem. Therefore, many investigations have been performed and various approaches to strengthening acrylic resin, for example, the reinforcement of heat-cured acrylic resin using glass fibers, have been suggested over the years. But problems such as poor workability, rough surface, poor adhesion of glass fiber resin complex are not solved yet. Purpose. The aim of the present study was to investigate the effect of short glass fibers on the transverse strength of heat-polymerized denture base acrylic resin and roughness of resin complex after abrasion test. Material and methods. To avoid fiber bunching and achieve even fiber distribution, glass fiber bundles were mixed with acrylic resin powder in conventional mixer with a non-cutting blade, to produce the glass fiber($10{\mu}m$ diameter, 3mm length, silane treated) resin composite. Glass fibers were incorporated at 0%, 3%, 6% and 9% by weight. Transverse strength were measured. After abrasion test, surface roughness was evaluated and scanning electron microscope view was taken for clinical application. Results. 1. 6% and 9% incorporation of 3mm glass fibers in the acrylic resin enhanced the transverse strength of the test specimens(p<0.05). 2. Before abrasion test, incorporation of 0%, 3%, 9% glass fiber in the resin showed no dirrerence in roughness statisticaly(p>0.05). 3. After abrasion test, incorporation of 0%, 3%, 6% glass fiber in the resin showed same surface roughness value statistically(p>0.05). 4. In SEM, surface roughness increased as the percentage of the fibers increased. 5. In the areas where glass fiber bunchings are formated, a remarkably high roughness was noticed. Conclusion. 6% and 9% addition of silane-treated short glass fibers into denture base acrylic resin increased transverse strength significantly. Before and after abrasion test, incorporation of 0%, 3%, 6% glass fiber in the resin showed same surface roughness value statistically.