• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.593-596
• /
• 2006

The environment-friendly building material, photocatalyst/scoria/loess concrete, was prepared using scoria and loess (which have merits as building materials) and photocatalyst (which has the functions to compose the environmental contaminants and of self cleaning). In order to apply this material as a building material, the compressive and flexible strengths, and water absorptivity (which have been set by Korea Industrial Standard) were measured. In order to know the environment-friendly characteristics of this material, several tests, such as, the tests of emissivity and emission power of far infrared ray and acoustic absorptivity, antibacterial test for Escherichia coli and Pseudomonas aeruginosa, antifungal test for mixed fungal strains, and deodorization test of ammonia were carried out. Moreover, the removal characteristics of NOx, and formaldehyde (HCHO) by photocatalyst/scoria/loess concrete were examined as the following different parameters: the removal characteristics of these contaminants with the substitution ratio and the kind of photocatalyst, light source, UV intensity of sunlight, relative humidity, intial NOx concentration.

• Journal of Mechanical Science and Technology
• /
• v.18 no.2
• /
• pp.272-285
• /
• 2004

The losses at off-design points from a compressor cascade occur due to the deviation from a design incidence angle at the inlet of the cascade. The self-noise from the blade cascade at off-design points comes from a separated boundary layer and vortex sheddings. If the incidence angle to the cascade increases, stalling in blades may occur and the noise level increases significantly. This study applied Large-Eddy Simulations (LES) using deductive and deductive dynamic SGS models to low Mach-number, turbulent flow with each incidence angle to the cascade ranging from -40$^{\circ}$ to +20$^{\circ}$ and compared numerical predictions with measured data. It was observed that the oscillating separation bubbles attached to the suction surface do not modify wake flows dynamically for cases of negative incidence angles. However, an incidence angle greater than 8$^{\circ}$ caused a separated vortex near the leading edge to be shed downstream and created stalling. The computed performance parameters such as drag coefficient and total pressure loss coefficient showed good agreement with experimental results. Noise from the cascade of the compressor is summarized as sound generated by a structure interacting with unsteady, turbulent flows. The hybrid method using acoustic analogy was observed to closely predict the measured overall sound powers and directivity patterns at design and off-design points of blade cascade.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.5
• /
• pp.90-95
• /
• 2007

Single side final polishing is a very important role to stabilize a wafer finally before the device process on the wafer is executed. In this study, the machining variables, such as pressure, machining time, and the velocity of pad table were adopted. These parameters have the major influence on the characteristics of wafer polishing. We investigated the surface roughness changing these variables to find the optimal polishing condition. Pad, slurry, slurry quantity, and oscillation distance were set to the fixed variables. In order to reduce defects and find a stable machining condition, a hall sensor was used on the polishing process. AE sensor was attached to the polishing machine to verify optimal condition. Applying data analysis of the sensor signal, experiments were performed. We can get better surface roughness from loading the quasi static force and improving wafer-holding method.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.934-938
• /
• 2008

To customize individual characteristics of HRTF, a spherical model has been used for structural modeling technique. A pseudo-code of prolate spheroidal HRTF caused by incident acoustic point source is already developed, and it can be used a head shadow filter for structural modeling of HRTF. In this research, to see the necessity and efficiency of spheroidal head modeling, ITD optimization is performed on CIPIC HRTF database. From given cost function, ITD-optimized spheroidal head model, whose ITD information is the most matched version of measured ITD information, is found by varying head parameters subject by subject. By comparing results of ITD-optimized spheroids and ITD-optimized spheres, we concluded that a spherical head model is more efficient way of generating head shadow effect than a spheroidal head model does.

• The Journal of the Acoustical Society of Korea
• /
• v.13 no.5
• /
• pp.24-31
• /
• 1994

In this paper, we study continuous speech recognition of Korean language using acoustic models of word juncture coarticulation. To alleviate the performance degradation due to coarticulation problems, we use context-dependent units that model inter-word transitions in addition to intra-word transitions. In all cases the initial phone of each word has to be specified for each possible final phone of the previous word similarly for the final phone of each word. To improve the robustness of the HMM parameters, the covariance matrix is smoothed. We also use position-dependent units to improve the discriminative power between units. Simulation results show that when the improved models of word juncture coarticulation are used. the recognition performance is considerably improved compared to the baseline system using only intra-word units.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.2
• /
• pp.153-159
• /
• 2010

This work focuses on finding a method to reduce the noise of a hermetic reciprocating compressor during start-up using an acoustical analysis. The noise of compressor during start-up, which is a higher level than that of a normal operating condition, has transient and non-stationary characteristics. The acoustical analysis of compressor cavity is performed to find an effective method to reduce the noise level. In the acoustical analysis, the shape variations of frequency response function in the neighborhood of resonances are tested for three parameters: the height of remained oil, the suction position of refrigerant and the position of driving part. As a conclusion of this result, to reduce the emission noise of compressor during start-up, the height of remained oil should be kept at 16 mm, the refrigerant should be sucked at the cross point of nodal lines of X and Y directional cavity modes, and the driving part should be positioned in the center of cavity.

• Phonetics and Speech Sciences
• /
• v.8 no.3
• /
• pp.51-59
• /
• 2016

The purpose of present study is to examine differences between habitual speech (HS) and clear speech (CS) in individuals with mild dysarthria. Twelve speakers with mild dysarthria and twelve healthy control speakers read sentences in two speaking styles. Formant and intensity related values, triangular area, and center of gravity of /a/, /i/, and /u/ were measured. In addition, formant-ratio variables such as vowel space area(VSA), vowel articulatory index (VAI), formant centralization ratio (FCR) and F2i/F1u ratio (F2 ratio) were calculated. The results of repeated-measures ANOVA showed a significant difference in F2 of vowel /i/ and F2 energy of vowel /a/ between groups. Regarding formant energy, F2 energy of vowel /a/ were observed as meaningful variables between speaking styles. There were significant speaking style-by-group interactions for F2 energy of vowel /a/. These findings indicated that current parameters could discriminate healthy group and mild dysarthria group meaningfully and that speaker with dysarthria had larger clear speech benefit than healthy talkers. We also claim that various acoustic changes of clear speech may contribute to improving vowel intelligibility.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2006.11a
• /
• pp.205-208
• /
• 2006

Similar friction welding were produced using 15 mm diameter solid bar in Ni-base superalloy(alloy718) to investigate their mechanical properties. The main friction welding parameters were selected to endure good quality welds on the basis of visual examination, tensile tests, AE total counts and ultrasonic attenuation coefficient. The specimens were tested as welded, not heat-treated. The tensile strength of the friction welded joints was increased up to 90% of the alloy718 base metal under the condition of all heating time. Optimal welding conditions were n=2,000 (rpm), $P_1=200$ (MFa), $P_2=200$ (MFa), $t_1=8$ (s), $t_2=5$ (s) when the total upset length is 4.4(mm). The weld interface of similar friction welded steel bars was mixed strongly.

• Journal of Korean Library and Information Science Society
• /
• v.48 no.1
• /
• pp.1-20
• /
• 2017

Public library is the most well-used cultural infrastructure, life-long learning space, and social facility within local community. In order to respond to the multi-purpose identities, space structure of many public libraries is changed or reconstructed to open-concept, multi-functional and interconnected areas. Accordingly, the noise issue in public libraries has emerged as one of key environmental parameters and noise management is bound to be considered as a scale for determining whether a user-friendly library. This study measured the noise level of the public libraries in Daegu city, analyzed measurement results on the basis of national and international standards, and suggested the various reduction plans.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.12
• /
• pp.608-616
• /
• 2006

Recently, a switched reluctance motor is widely used in various industries because it has many advantages such as a simple structure, robustness, less maintenance, high torque/weight ratio, and easy speed control over other types of motors. However, a switched reluctance motor inherently produces acoustic noise and vibration caused by torque ripple. Applications of these motors where silent operation is desirable have thus been limited. In this paper, a new stator pole face having a non-uniform air-gap and a pole shoe attached to the lateral face of the rotor pole are suggested in order to minimize torque ripple. The effects of each design parameter are validated using a time-stepping finite element method. The parameters are optimized by utilizing response surface method (RSM) combined with (1+1) evolution strategy. The result shows that the optimized shape gives higher average torque and drastically reduced torque ripple.