• 한국항공우주학회지
• /
• 제33권12호
• /
• pp.39-47
• /
• 2005

본 연구에서는 고속 충격환경을 경험하는 플라스틱 구조 소재에 대한 인장속도별 물성 평가 시험 및 구조건전성 평가에 음향방출 기법을 적용하였다. 인장속도별 물성 평가시험을 통하여 플라스틱 소재 구조물의 건전성 평가에 유용한 음향방출 신호 특성 인자들을 획득하였다. 인장속도에 따른 인장강도는 저속 인장속도 구간에서는 속도가 증가함에 따라 강도가 증가하는 특성을 보여주었으나 일정 속도 영역 이상의 고속 인장시험에서는 인장속도 증가와 무관하게 일정한 강도 값을 나타내었다. 정적 압축 구조시험에서는 음향방출 기법을 적용함으로써 플라스틱 쉘 구조물의 균열발생 시점 및 위치 등을 정확히 평가할 수 있었다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.197-202
• /
• 2006

The low-altitude earth observation satellite is generally equipped with high performance camera as a main payload which is vulnerable to vibration environment. During the launch process of a satellite, the combustion and jet noise of launch vehicle produce severe acoustic environment and the acoustic loads induced may damage the critical equipments of the satellite including the camera. Therefore to predict and simulate the effect of the acoustic environment which the satellite has to sustain at the lift-off event is very important process to support the load-resistive design and test-qualification of components. Statistical Energy Analysis(SEA) has been widely used to estimate the vibro-acoustic responses of the structures and gives statistical but reliable results in the higher frequency region with less modeling efforts and calculation time than the standard FEA. In this study, SEA technique has been applied to a 3-Dimensional model of a low-altitude earth observation satellite to predict the acceleration responses on the structural components induced by the high level acoustic field in the launch vehicle fairing. In addition, the expected response on each critical component panel was calculated by the classical method in consideration of the mass loading and imposed sound pressure level, and then compared with SEA results.

• 한국자동차공학회논문집
• /
• 제7권9호
• /
• pp.158-164
• /
• 1999

In this paper a simple measurement technique for mechanical-acoustic transfer functions is proposed . The mechanical-acoustic transfer functions, generally , are measured through mechanical excitations ; impact hammers or shakers. Recently , by virtue of vibro-acoustical reciprocity principle, they are measured through acoustic excitations : loudspeakers. This kind of test needs to measure the volume velocity , the radiation characteristics of a sound source. Because the volume velocity of the sound source is changed by driving signal , it is difficult to measure it. However , the new method in this paper needs not to measure the volume velocity of a sound source by combination of mechanical and acoustic excitations. Moreover, this method has the methodological advantages, such as usage of a general loudspeaker for the reciprocal excitation, no sptatial limitations for measurements of mechanical-acoustic transfer functions.

• 한국공작기계학회논문집
• /
• 제16권1호
• /
• pp.26-32
• /
• 2007

This study was carried out fusion-welded butt joints in SWS 490A high strength steel subjected to tensile test that load-deflection curve. The windowed or short-time Fourier transform(WFT or STFT) makes possible for the analysis of non-stationary or transient signals into a joint time-frequency domain and the wavelet transform(WT) is used to decompose the acoustic emission(AE) signal into various discrete series of sequences over different frequency bands. In this paper, for acoustic emission signal analysis to use a continuous wavelet transform, in which the Gabor wavelet base on a Gaussian window function is applied to the time-frequency domain. A wavelet transform is demonstrated and the plots are very powerful in the recognition of the acoustic emission features. As a result, the technique of acoustic emission is ideally suited to study variables which control time and stress dependent fracture or damage process in metallic materials.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.96-102
• /
• 2001

High intensity vibro-acoustic testing is the appropriate method for flight qualification testing of space flight vehicle which must ensure the acoustic environment of launch. Growing demand for satellites and launch vehicles in korea has resulted in a recent increase in the demand for high intensity vibro-acoustic test facility. The test facility is designed to provide an acoustic environment of 152 ㏈( re 20 ${\mu}$Pa) overall sound pressure level over the band width of 30 Hz to 10,000 Hz in the reverberant chamber. The reverberant chamber has a volume of 1,000 ㎥ with interior dimensions of 8.7m${\times}$l0m${\times}$12m, which can accommodate not only satellites but also launch vehicle payload fairing. Korea Aerospace Research Institute and Korean industries have been carrying out the development of the reverberant chamber and auxiliary devices, such as automatic control system, monitoring/safety device, and jet nozzle, etc. This paper presents the detailed description of High Intensity Acoustic Chamber of KARI, which will be the first and unique testing facility in Korea.

• 한국소음진동공학회논문집
• /
• 제16권10호
• /
• pp.1057-1066
• /
• 2006

Acoustic streaming Induced by longitudinal vibration at 30 kHz is visualized for a test fluid flow between the stationary glass plate and ultrasonic vibrating surface with particle imaging velocimetry (PIV) To measure an increase in the velocity of air flow due to acoustic streaming, the velocity of air flow in a gap between the heat source and ultrasonic vibrator is obtained quantitatively using PIV. The ultrasonic wave propagating into air in the gap generates steady-state secondary vortex called acoustic streaming which enhances convective cooling of the stationary heat source. Heat transfer through air in the gap is represented by experimental convective heat transfer coefficient with respect to the gap. Theoretical analysis shows that gaps for maximum heat transfer enhancement are the multiple of half wavelength. Optimal gaps for the actual design are experimentally found to be half wavelength and one wavelength. A drastic temperature variation exists for the local axial direction of the vibrator according to the measurement of the temperature distribution in the gap. The acoustic streaming velocity of the test fluid in the gap is at maximum when the gap agrees with the multiples of half wavelength of the ultrasonic wave, which are specifically 6 mm and 12 mm.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2005년도 춘계학술대회 논문집
• /
• pp.342-348
• /
• 2005

This study was carried out fusion-welded butt joints in SWS 490A high strength steel subjected to tensile test that load-deflection curve. The windowed or short-time Fourier transform (WFT or SIFT) makes possible for the analysis of non-stationary or transient signals into a joint time-frequency domain and the wavelet transform (WT) is used to decompose the acoustic emission (AE) signal into various discrete series of sequences over different frequency bands. In this paper, for acoustic emission signal analysis to use a continuous wavelet transform, in which the Gabor wavelet base on a Gaussian window function is applied to the time-frequency domain. A wavelet transform is demonstrated and the plots are very powerful in the recognition of the acoustic emission features. As a result, the technique of acoustic emission is ideally suited to study variables which control time and stress dependent fracture or damage process in metallic materials.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 제33회 추계학술대회논문집
• /
• pp.399-402
• /
• 2009

로켓엔진 연소기의 음향 불안정 억제를 위해 헬름홀츠 공명기의 음향학적 최적 설계 설계조건을 실험적, 해석적으로 연구하였다. 표준 음향시험 절차에 따라 음향파관에 공명기를 장착하여 음향파응답 신호를 측정하였다. 측정된 신호를 토대로, 흡음계수를 계산하였고, 이로부터 공명기의 음향감쇠 성능을 파악하였다. 헬름홀츠 공명기를 스프링-댐퍼 시스템으로 상사하여, 음향학적 감쇠성능을 이해하였다. 헬름홀츠 공명기의 설계변수로 목의 길이와 공동의 크기 등을 선택하였다. 공동의 크기가 커질수록 흡음성능이 증가하였고, 목 길이가 길어질수록 흡음성능이 감소하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.743-748
• /
• 2010

The stability forecasting of rock slope is more difficult than soil slope because catching the sign of failure in monitoring is not easy and deformation of the rock is small in failure process. But in the rock slope, there is small deformation like crack propagation in rock itself and it accumulates gradually in failure process. If it is possible to detect the small change in the rock slope, we can know the failure time exactly. Because the individual signal is gathered in the acoustic emission monitoring, it is possible to monitoring the slope if many sound signal is accumulated. Detection test of acoustic emission was performed. Uniaxial, two types of bending test, and two plane shear test were done with various cement paste sample. Wave propagation velocity of uniaxial test sample was increased with curing time. Wave Analysis give us the result that there is a AE sign signal before the failure, the AE count is suddenly increased. And frequency level 125kHz before failure is changed to level 200-250kHz after failure. In two plane shear test we can catch the AE signal and can know the failure type from wave shape. Monitoring test site is tunnel slope in Hongcheon but special signal is not collected.

• 재활복지공학회논문지
• /
• 제1권1호
• /
• pp.21-28
• /
• 2007

대부분의 보청기에서는 난청인의 청력 손실을 보상하기 위해 음성 증폭 알고리즘과 잡음 및 피드백을 제거하기 위한 알고리즘 등을 사용하고 있고, 음성의 인지율을 높이기 위해서 음성의 대비를 강조하는 알고리즘을 사용한다. 음성 대비 강조 알고리즘 사용 시 과도한 대비증폭에 의해서 포먼트(formant) 사이에서 마스킹 현상이 발생할 수 있다. 마스킹 현상을 확인하기 위해서 6가지의 주관적인 평가와 1가지의 객관적인 평가를 수행하였다. 주관적인 평가로는 순음 검사, 어음 청취 역치 검사, 낱말 분별력 검사, 순음 마스킹 검사, 포먼트 순음 마스킹 검사, 어음 마스킹 검사로 이루어져있고 객관적인 평가를 위해서 LLR(log likelihood ratio)을 도입하였다. 정상 청각 피험자와 난청 피험자의 결과로 미루어 볼 때, 난청 피험자가 마스킹이 잘 일어난다는 것을 볼 수 있었고, 어음을 이용한 마스킹 검사에서는 마스킹에 의해서 난청 피험자에서 어음에 대한 인지율이 떨어지는 결과를 볼 수 있다. 이러한 현상은 포먼트 향상에 의한 왜곡 때문이 아닌 마스킹 때문이다. 그러므로 마스킹 효과의 특성을 조사하여, 보청기 적합 시, 이러한 마스킹 특성을 고려하는 것이 필요하다.