• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 추계학술대회 논문집
• /
• pp.119-124
• /
• 2005

Decision of operation performance mode to minimize the energy consumption of urban rail vehicle. This paper analyses how much acceleration and deceleration of urban rail vehicle should be applied andhow to choose an operation mode to minimize energy consumption when train runs between station within the fixed operation time. The decided operation pattern satisfying the minimum energy consumption becomes a target trajectory and a basis for the controller design criteria. To make this goal it grasps the characteristics of urban rail vehicle, realize operation energy model of urban rail vehicle and verify the accuracy of embodied model the Matlab simulation with the same operation result of real route. It searches for operation pattern to minimize operation energy by changing the acceleration and deceleration on the imaginative route and proposes operation pattern minimizing energy consumption by applying real operation data between Dolgogee-Sukgye section of Seoul Metropolitan Subway Line 6.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 B
• /
• pp.935-937
• /
• 2004

This paper is proposed vibration minimize method of slotted PMLSM which is designed to minimize detent force. For improvement of operational performance by changing velocity profile to reducing the vibration at discontinuous section of acceleration curve in this paper, proter type machine is made, the vibration is compared general trapezoid velocity profile with vibration minimization velocity profile.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 B
• /
• pp.797-799
• /
• 2004

The discontinuous primary linear synchronous motor is proposed as a driving source in the middle-distance transportation systems in factories and facilities. This paper describes the examination about the acceleration characteristics and a synchronizing method when the secondary mover overlaps with the primary from the inertia travel motion section in the whole of the re-acceleration part.

• Nuclear Engineering and Technology
• /
• 제54권11호
• /
• pp.4280-4295
• /
• 2022

In this paper, a new multi-group neutron-gamma transport calculation code system STRAUM-MATXST for complicated geometrical problems is introduced and its development status including numerical tests is presented. In this code system, the MATXST (MATXS-based Cross Section Processor for S_N Transport) code generates multi-group neutron and gamma cross sections by processing MATXS format libraries generated using NJOY and the STRAUM (S_N Transport for Radiation Analysis with Unstructured Meshes) code performs multi-group neutron-gamma coupled transport calculation using tetrahedral meshes. In particular, this work presents the recent implementation and its test results of the Krylov subspace methods (i.e., Bi-CGSTAB and GMRES(m)) with preconditioners using DSA (Diffusion Synthetic Acceleration) and TSA (Transport Synthetic Acceleration). In addition, the Krylov subspace methods for accelerating the energy-group coupling iteration through thermal up-scatterings are implemented with new multi-group block DSA and TSA preconditioners in STRAUM.

• 한국안전학회지
• /
• 제31권5호
• /
• pp.89-94
• /
• 2016

The objective of this study was to estimate the dynamic behavior of a personal rapid transit(PRT) track system using a rail of rectangular tube section and a rail joint of sliding type, and to compare the results with the normal rail and rail joint of a PRT track system by performing field measurements using actual vehicles running along the service lines. The measured vertical displacement of rail and sleeper, and vertical acceleration of rail for the normal rail and rail joint section were found to be similar, and the rail joint of sliding type satisfied the design specifications of the track impact factor for a conventional railway track. The experimental results showed that the overall dynamic response of the rail joint were found to be similar to or less than that of the normal rail, therefore the rail joint of sliding type for PRT track system was sufficient to ensure a stability and safety of PRT track system.

• 국제초고층학회논문집
• /
• 제7권3호
• /
• pp.233-242
• /
• 2018

Since the response reduction effect on over 200-meter-tall resulting from the seismic isolation system is smaller in general than low-rise and mid-rise buildings, mid-story isolated buildings are considered to reduce the response in the upper part above the isolation story, however, in many cases, the acceleration response just below the isolation story is likely to be the largest. This paper presents the structural design schemes, the design of the main structural frames, and the constructions of a 230-meter-tall super high-rise building with mid-story isolation mechanism integrated in Roppongi, Tokyo. Moreover, this paper shows how the architectural and structural design for integrating a mid-story isolation system in a super high-rise building has been conducted and what solutions have been derived in this project. The realization of this building indicates new possibilities for mid-story isolation design for super high-rise buildings.

• 태양에너지
• /
• 제19권3호
• /
• pp.93-100
• /
• 1999

The objective of this experimental study was to investigate the characteristics of heat transfer and air flow in two-dimensional impinging jet system, in which hybrid rods have been set up in front of heating surface in order to increase heat transfer. The shape of hybrid rods had a cross section made with a half of circular cross section and that of rectangular. This time, the clearance from hybrid rod to heating surface(C=1, 2, 4mm) and the pitch between each hybrid rods(P=30, 40, 50mm) changed for the transition region(H/B=10). And this result compared with the experimentation without hybrid rod. As a result, heat transfer performance was best under the condition of C=1mm, in case clearance changed, and as the pitch is 30mm, it is largely influenced by eddies and acceleration in case pitch of hybrid rod changed.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제8권1호
• /
• pp.39-59
• /
• 2008

The performance of weapon system, based on the acceleration of advanced scientific technology, has been reinforced to the state of precision, complexion and multi-function. People have given great interest for a long time on its development, acquisition cost and enormous expense of operation/support. Under this environmental situation, this research paper proposes two kinds of implementation that can improve the RAM(Reliability, Availability, Maintainability) on weapon system. The first section is to understand all of the actual states on its reliability, in the acquisition process and to make the improvement for RAM at the milestones on the acquisition steps. The next section is to establish a defense RAM center, which will be closely cooperated with acquisition organization such as Ministry of Defense, DAPA(Defense Acquisition Program Administration), DTaQ(Defense agency for Technology and Quality) and ADD(Agency for Defense Development), etc. and to conclusively improve the RAM of weapon system in South Korea.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.867-872
• /
• 2002

The seismic design from the underground structures with the ground structures differently relative acceleration of ground and structure for, that period ci it was a condition where the recognition against the seismic design of the underground structure is insufficient because the decease damage does not very to that extent. Analysis result, earthquake hour section power increase one that price smiles from one part and when it applies a regular design hour safety rate 20%, seismic efficiency level satisfaction is it becomes feed with the fact that it will be able to augment the efficient characteristic of design.

• 대한교통학회지
• /
• 제17권2호
• /
• pp.69-79
• /
• 1999

본 연구에서는 고속도로의 기본구간과 비교해 볼 때, 고속도로 합류부에서의 운전자의 각성정도의 변화를 생리적 신호 중 후두엽부(Occipital Lobe)의 뇌파 중 $\beta$파를 측정하여 정량화하여 살펴보았다. 고속도로 기본구간 3지점과 합류부 구간 3지점에서 실험차량을 이용하여 남자 8명, 여자 2명, 총 10명의 피실험자를 대상으로 실험한 결과 고속도로 운전자는 합류부 구간(램프주행구간, 가속차로시점에서 합류직전 구간, 합류부 영향이 남아 있는 주행구간)에서 운전시 기본 주행구간에 비하여 가속차로 시점에서 합류 직전구간에서 2.21배로 가장 큰 각성정도를 보였다. 또한 고속도로 운전자는 합류를 완료한 후에 4초간 합류과정으로 인한 영향이 남아 있는 것으로 분석되었다. 특히 운전자들은 고어지점으로부터 80m구간이내에서 합류하는 것이 충분한 가속주행을 한 것보다 더 각성 정도를 보였다.