• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.1244-1250
• /
• 2008

The site of interest is a residence redevelopment area which has excavation construction with cut-off walls. The site is located over Dong-Mang-Bong tunnel and Seoul No. 6 subway tunnel. This study analyzed numerically the influence of vibrations from No. 6 subway tunnel to the basement of the redeveloped apartment away from the distance about 11m. Kyoung-bu highspeed railway's time history model with linearly reduced maximum acceleration is applied to take into the subway maximum speed of 75km/h. The maximum velocity of vibration for the cross section of the interest was estimated as 0.28cm/sec which satisfied the allowable standard of 0.5cm/sec for apartment and residence of Seoul.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.305-308
• /
• 2006

In this paper, the seismic performance of SRC piers for near fault motions was evaluated by shaking table tests on small scale models. Dead load of the superstructures was simulated by axial prestress at the center of the column section. A mass frame linked with steel bars was fabricated to include the effect of superstructure mass. Friction of the mass frame when it moves was minimized by special details and it was proved before tests. Five pier models with 400mm diameter were tested by increasing the acceleration of the near fault motion. Test results were discussed and compared with previous quasi-static tests.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.85-88
• /
• 2006

This paper deals with shaking table tests on RC piers to evaluate the seismic performance under near fault motion. Small scale models were fabricated and axial force was applied by introducing prestress at the centroid of the column section. Mass effect of the superstructures was simulated by mass frame which was linked with a pier model by steel bars because of the limited payload of shaking table. Friction of the mass frame when it moves was minimized by special details and it was proved before tests. Scale factor of the RC piers was 4.25. Main parameters of the test were details of reinforcements. After verifying the results of shaking table tests, seismic performance was evaluated by increasing the acceleration of the near fault motion.

• 대한교통학회:학술대회논문집
• /
• 대한교통학회 1998년도 Proceedings The 4th International Transport Symposium
• /
• pp.141-151
• /
• 1998

Provision of Passing Sight Distance (PSD) is an important component in two-lane highway design and has a critical impact on capacity of highway and safety of drivers. Many models have been developed to estimate PSD reasonably. However, each of them has a number of shortcomings for reflecting the real traffic conditions. This paper introduces a revised model that reflects the characteristics of the passing maneuver. The changes in passing sight distances under different assumptions about acceleration and vehicle length, which are related to vehicle types, are presented. The results obtained by the revised model are compared with those obtained from the existing models. There is an important link between geometric design decisions which determine the available sight distance and the quality of service which the road provides. In this paper, we examine one aspect of this relationship. That is to determine whether the passing sight distance is provided by improving horizontal alignment for a specific roadway section or passing may be restricted to save the road construction cost. To do so, a simple method for estimating traffic delay in no-passing is introduced.

• Journal of Advanced Marine Engineering and Technology
• /
• 제7권1호
• /
• pp.14-22
• /
• 1983

The Bourdon tube pressure gauge is the most widely used primary detector for pressure in various kinds of fields recently. However in many cases lots of difficulties are encountered in telemetering, measuring the continuously changing pressure and recording as time goes by, etc. In this paper a Bourdon tube of flat-oval section is considered. On the basis of Wolf's theory, the very sensitive places are selected on the tube and full bridge arrangement is used. Then all of the characteristics are examined in order to use the pressure transducer practically into which the pressure gauge is converted. From the results, the error in meter reading is about $\pm$3% F.S., on the other hand, when measured with strain gauge, the error is within $\pm$1% F.S.. Also external acceleration on Bourdon tube hardly affect practical use.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 II
• /
• pp.1394-1399
• /
• 2001

The purpose of this paper is that investigates the dynamic behavior characteristic of W.T.S(Wind Turbine System) and carries out the evaluation analysis during operating W.T.S. To investigate the dynamic behavior characteristic of W.T.S. the experiments to measure vibration of the blade from the attached accelerometer on the flap and edge section of the blade that is one of the most important elements of dynamic characteristic of W.T.S are performed. Natural frequency and mode shape are calculated with commercial program (STAR MODAL) using the measured vibration acceleration that receives the signal with F.F.T Analyzer from the accelerometer. For validation of these experiments. the finite element analysis is performed with commercial F.E.M Program (ANSYS) on the basis of the natural frequency and mode shape. The results indicate that experimental values have good agreements with the finite element analysis.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.574-578
• /
• 2008

In order to achieve thrust vector control and discharge stabilization in Hall thrusters, the azimuthal nonuniformity of propellant flow rate in an acceleration channel was created. A plenum chamber was divided into two rooms by two walls and propellant flow rate supplied to each section was independently controlled. In a magnetic layer type Hall thruster, steering angle of up to ${\pm}2.3$ degree was achieved. In an anode layer type Hall thruster, discharge current oscillation amplitude was decreased with the normalized differential mass flow rate.

• ETRI Journal
• /
• 제45권2호
• /
• pp.329-337
• /
• 2023

For safe last-mile autonomous robot delivery services in complex environments, rapid and accurate collision prediction and detection is vital. This study proposes a suitable neural network model that relies on multiple navigation sensors. A light detection and ranging technique is used to measure the relative distances to potential collision obstacles along the robot's path of motion, and an accelerometer is used to detect impacts. The proposed method tightly couples relative distance and acceleration time-series data in a complementary fashion to minimize errors. A long short-term memory, fully connected layer, and SoftMax function are integrated to train and classify the rapidly changing collision countermeasure state during robot motion. Simulation results show that the proposed method effectively performs collision prediction and detection for various obstacles.

• 한국운동역학회지
• /
• 제24권1호
• /
• pp.67-74
• /
• 2014

This study researched into the left-right inclination of the rear foot at the lower limb joints, knee joint angle, angular velocity of the knee joint, angular acceleration and the max. Based on the analysis of kinematics according to the changes in the height of step box (6, 8, 10 inches) during step aerobics of female college students majoring in physical education. The findings of this study are as follows: Then angle of the knee joint decreased as the height of the step box increased the min. Angle was measured right before the right foot was on the step box, and the angle tended to decrease as the step box get heightened. The left-right inclination of the rearfoot angle according to the height of step box increased as the height increased. In the 'pull-up' stage during which the weight was loaded on the right foot the angle increased, while in the right foot stepping stage during which the right foot was on the ground, the left-right inclination of the rearfoot angle increased as the height of the step box increased. The angular velocity of the knee joint according to the height of step box started increasing when the right foot initially stepped on the step box and during the initial stepping section, the angular velocity decreased as the height of step box increased. The changes in angular acceleration of the knee joint according to the height of step box increased as the height of step box increased.

• 한국지반신소재학회논문집
• /
• 제10권4호
• /
• pp.81-92
• /
• 2011

본 연구에서는 흙 댐 구조물의 지진저항 특성을 파악하기 위하여 3가지 대표단면을 기초로 하여 축소모형의 비율에 해당하는 상사법칙을 고려하여 각각 1:100, 1:70, 1:50으로 토조를 제작하였다. 그리고 국내 설계기준에 준하여 장주기인 Hachinohe파, 단주기인 Ofunato파, 인공지진파를 가진하여 각 단면에 대해 가속도변화, 과잉간극수압, 수직 및 수평변위를 측정하고, 측정된 결과를 통하여 지반-구조물-유체의 상호작용에 따른 안정성을 평가하였다. 시험결과 시험 대상 단면의 변위는 지진 시 허용변위량 300mm에 비해 비교적 작은 변위로 지진 시 안정성을 확보하였다. 가속도 계측결과 Hachinohe파, Ofunato파는 할증률 20%정도로 평가되었지만 인공지진파는 할증률 30%정도로 평가되었다. 과잉간극수압비 측정결과 액상화 평가기준인 과잉간 극수압비 1이하로 모형단면은 액상화에 대해 안정성을 확보하였다.