• 한국지진공학회논문집
• /
• 제7권5호
• /
• pp.11-17
• /
• 2003

일반적으로 토목구조물에서 계측된 가속도 신호의 대부분은 적분이 매우 힘들다. 그 이유는 토목구조에서 계측된 가속도 신호는 일반적으로 비정상신호이며 또한 비가우시안 노이즈와 저주파 노이즈를 포함하고 있어, 저주파 성분이 증폭되는 적분과정에서 수치적 불안정성이 발생할 수 있기 때문이다. 따라서, 본 논문에서는 비정상 신호처리에 탁월한 웨이블릿 변환의 개념을 비가우시안 노이즈와 저주파 노이즈에 대해 확장한 수정된 웨이블릿 변환을 이용한 가속도 기록의 이중 적분방법을 제시하였다. 또한, 예제해석을 통해 제시된 방법이 비정상 신호의 노이즈 및 비가우시안 노이즈와 저주파 노이즈를 제거에 우수한 성능을 보이고 있음을 보였다.

• 한국생산제조학회지
• /
• 제22권4호
• /
• pp.658-664
• /
• 2013

In this paper, we present a case study of vibration suppression based on the application of active damping to the small boring process of a boring bar with diameter below ${\Phi}12$. The proposed active damping system consists of an acceleration sensor for real-time monitoring of the vibration signal, a driver for phase control in a computer program, and piezoelectric actuators for damping. In this system, the vibration signals are detected by the acceleration sensor and sent to the computer as an input. The phase shift parameter of the natural frequency of the input signal is sent to the data acquisition board in the computer and calculated by the phase control program. This study confirmed the effectiveness of this damping system, and it opens up the possibility of the development of active damping systems for small boring processes.

• 인터넷정보학회논문지
• /
• 제18권3호
• /
• pp.11-17
• /
• 2017

To the elderly, sudden falls are one of the most frightening accidents. If an accident occurs, a prompt action has to be taken to deal with the situation. Recently, there have been a number of attempts to detect sudden falls using acceleration sensors embedded in the mobile devices, such as smart phones and wrist-bands. However, using the sensor readings only, the detection rate of the falls is around 65%. Ordinary daily activities such as running or jumping could not be well distinguished from the falls. In this paper, we describe our attempts on improving the fall-detection rate. We implemented a wrist-band fall detection module, using a three-axis acceleration sensor. With the pattern matching on the fall signal-strength frequency spectrum, in addition to the conventional signal strength measurement, we could improve the detection rate by 9% point. Furthermore, by applying two wrist-bands in the experiment, we could further improve the detection rate to 82%.

• 한국산업융합학회 논문집
• /
• 제23권2_2호
• /
• pp.163-171
• /
• 2020

The condition of tire tread is a key parameter closely related to the driving safety of a vehicle, which affects the contact force of the tire for braking, accelerating and cornering. The major factor influencing the contact force is tread wear, and the more tire tread wears out, the higher risk of losing control of a vehicle exits. The tire tread condition is generally checked by visual inspection that can be easily forgotten. In this paper, we propose the intelligent tire (iTire) system that consists of an acceleration sensor, a wireless signal transmission unit and a tread classifier. In addition, we also presents classification algorithm that transforms the acceleration signal into the frequency domain and extracts the features of several frequency bands as inputs to an artificial neural network. The artificial neural network for classifying tire wear was designed with an Multiple Layer Perceptron (MLP) model. Experiments showed that tread wear classification accuracy was over 80%.

• 한국생산제조학회지
• /
• 제24권2호
• /
• pp.203-210
• /
• 2015

This paper investigates the failure of a car with a 2.5-liter CRDi engine of the Hyundai Company. The failure is caused by intermittent poor acceleration while driving. To analyze the cause, we investigated the air intake volume, the fuel injection, and the air-fuel ratio, which were determined to be normal. The brake switch signal error was discovered while analyzing the function that limits the output of the engine. While investigating the cause, we discovered the corrosion of the pins on the connector of the brake switch. We determined that it was generated by soapy water flowing in the solar film. Therefore, the cause of the failure was the brake switch signal errors. Additionally, we determined that ECM was the normal fail-safe mode that implemented the override device for safety during normal acceleration. Based on these results, further solar film experiments must be conducted to fully elucidate the causes.

• 센서학회지
• /
• 제25권3호
• /
• pp.202-207
• /
• 2016

Estimation of vertical position is critical in applications of sports science and fall detection and also controls of unmanned aerial vehicles and motor boats. Due to low accuracy of GPS(global positioning system) in the vertical direction, the integration of IMU(inertial measurement unit) with the GPS is not suitable for the vertical position estimation. This paper investigates an IMU-barometer integration for estimation of vertical position (as well as vertical velocity). In particular, a new two-step Kalman/complementary filter is proposed for accurate and efficient estimation using 6-axis IMU and barometer signals. The two-step filter is composed of (i) a Kalman filter that estimates vertical acceleration via tilt orientation of the sensor using the IMU signals and (ii) a complementary filter that estimates vertical position using the barometer signal and the vertical acceleration from the first step. The estimation performance was evaluated against a reference optical motion capture system. In the experimental results, the averaged estimation error of the proposed method was 19.7 cm while that of the raw barometer signal was 43.4 cm.

• 한국추진공학회지
• /
• 제11권2호
• /
• pp.62-70
• /
• 2007

지향성능은 발사차량의 정확성에 있어서 중요한 요소이다. 본 연구는 외란 가속도를 이용하여 지향구조물의 진동을 감지하는 방안과 실험 결과에 대하여 기술하였다. 주행 중 발생하는 진동 경향을 분석하기 위하여 가속도 자료를 이동평균과 힐버트 변환을 이용하여 신호 처리하였다. 다양한 외란에 대하여 가속도의 모드 계수를 얻었으며, 차량속도, 노면조건, 지향구조물의 특성을 차량 동특성의 진동을 변화시키는 요소로 간주하였다. 마지막으로 다양한 주행 조건의 진동 신호를 분류하기 위한 패턴인식에 역전파 신경망 이론을 이용하였다. 각 조건에 대하여 실험 결과를 비교 분석하였다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.167.3-167
• /
• 2001

In this paper, a single degree-of freedom gimbal-structured micro gyroscope and signal processing part including capacitive sensing circuits and filters are designed, fabricated and experimented. We use capacitive sensing method with excitation signal, i.e. sensing excitation signal, to measure the displacement of the moving plate. So, Sensing Output Signal is modulated twice by the excitation signal and driving signal, which is profitable to decouple the driving and sensing mode, to reduce the effect of the acceleration, and to curtail the noises due to parasitic capacitance and driving signal. To reduce driving noises and to improve linearity, the excitation signals and driving signals are modified. Through frequency response analyses ...

• 제어로봇시스템학회논문지
• /
• 제2권2호
• /
• pp.115-120
• /
• 1996

In this paper, a sliding mode controller which is characterized by high accuracy, fast response and robustness is applied to speed control of AC-SERVO motor. The control input is changed to the continuous one in the boundary layer to reduce the chattering phenomenon, and the boundary layer converges to zero when the state variables of system reach to steady state values. The integral compensator is added to reduce steady state error and to provide the continuous torque reference. The acceleration which is necessary for the sliding plane is estimated by an obsever. Sliding surface is included in control input to enhance the robustness and transient response without increasing sliding mode controller gain. The proposed controller is implemented by DSP(digital signal processor). The effectiveness of the proposed scheme is demonstrated through experimental works.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 춘계학술대회 논문집
• /
• pp.466-471
• /
• 2003

In order to analyze linear motor driven feed system, preliminary studies have been conducted focusing on the performance evaluation of the system based on the various combination of control gain along with acceleration. Tentative simulation revealed that due to the complexity of control system reduced number of control condition is recommended. Actual machining process with conventional feed system using endmill tool was employed as a preliminary study. Several sensing methods including AE, acceleration sensors and tool dynamometer were used. Results revealed the consistency in AE and cutting resistance. There were inconsistent empirical results in accelerometer probably due to the insensitivity of the sensor signal with respect to the experimental system