• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.05a
• /
• pp.182-183
• /
• 2017

This research identifies radon gas absorption mechanism by adsorption materials, replacing gypsum board with radon emissions, the density and absorption rates of magnesium were carried out using vermiculite, anthracite, powdered active carbon, bentonite, illite, diatomite as a basic study on the fire resistance type of radon Gas reduction type with absorption and decomposition. As a result of the experiment, diatomite showed the lowest density, and the highestt value was the highest. For the absorption rate, bentonite showed the highest absorption rate, and the anthracite showed the lowest absorption rate.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.45 no.3
• /
• pp.59-64
• /
• 2003

Hwangto would be an environment-friendly material that can be readily used. The purpose of this study is to obtain the absorption ratio, ultrasonic pulse velocity and neutralization of the mortar with non-active Hwangto and stone dust. The absorption ratio and neutralization depth are increased with increase of non-active Hwangto. But, the ultrasonic pulse velocity is decreased with increase of non-active Hwangto. In results of SEM analysis, the crystals are increased with increase of non-active Hwangto.

• Journal of Environmental Science International
• /
• v.20 no.4
• /
• pp.501-509
• /
• 2011

Unlike many laboratory-scale studies on absorption of organic compounds (VOCs), limited pilot-scale studies have been reported. Accordingly, the present study was carried out to examine operation parameters for the effective control of a hydrophilic VOC (methyl ethyl ketone, MEK) by applying a circular pilot-scale packed-absorption system (inside diameter 37 cm ${\times}$ height 167 cm). The absorption efficiencies of MEK were investigated for three major operation parameters: input concentration, water flow rate, and ratio of gas flow-rate to washing water amount (water-to-gas ratio). The experimental set-up comprised of the flow control system, generation system, recirculation system, packed-absorption system, and outlet system. For three MEK input concentrations (300, 350, and 750 ppm), absorption efficiencies approached near 95% and then, decreased gradually as the operation time increased, thereby suggesting a non-steady state condition. Under these conditions, higher absorption efficiencies were shown for lower input concentration conditions, which were consistent with those of laboratory-scale studies. However, a steady state condition occurred for two input concentration conditions (100 and 200 ppm), and the difference in absorption efficiencies between these two conditions were insignificant. As supported by an established gas-liquid absorption theory, a higher water flow rate exhibited a greater absorption efficiency. Moreover, as same with the laboratory-scale studies, the absorption efficiencies increased as water-to-gas ratios increased. Meanwhile, regardless of water flow rates or water-to-gas ratios, as the operation time of the absorption became longer, the pH of water increased, but the elevation extent was not substantial (maximum pH difference, 1.1).

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.489-492
• /
• 2003

The results of an experiment on the sound absorption of the porous concrete and its influence on the compressive strength are reported in this paper. Two different sizes of coarse aggregate of 5~13, 13~20mm, and the design void ratio of 20, 25 and 30 percent for a given size of aggregate were used. In the compressive strength, an aggregate of the size of 5~13mm is much higher strength than that of the 13~20mm, In the sound absorption experiment, the size of aggregate of 5~l0mm is much higher sound absorption than that of the 13~20mm. The sound absorption ratio was increased as the design void ratio. As a result, Porous concrete sufficiently have the performance of sound absorption.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1998.04a
• /
• pp.659-663
• /
• 1998

To measure the absorption ratio and the transmission loss of a material, a usage of the reverberation room has been popular. However, the reverberation room is expensive to build it and, sometimes, test procedure is not easy. Therefore, to get the data of absorption ratio, several possible technologies has been proposed using the tube. Among these technologies, with the analysis of the spectral density, a convenient method has been introduced to measure both the absorption ratio and transmission loss. The measured data has been compared with the results of the measurement at the reverberation room.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.10
• /
• pp.990-998
• /
• 2004

Dynamic behavior of an ammonia-water absorption system was investigated numerically. Thermal-hydraulic model for a single-effect 3 RT chiller was developed by applying transient conservation equations of total mass, $NH_3$ mass, energy and momentum to each component. Transient variations of system properties and transport variables were analysed during start-up operation. Numerical analyses were performed to quantify the effects of bulk concentration and charging ratio on the system performance in terms of cooling capacity, coefficient of performance, and time constant of system. For an absorption chiller considered in the present study, optimum charging ratio and bulk concentration were to found to exist, which resulted in the maximum cooling capacity and COP. The time constant increased as the charging ratio increased, but decreased with the increase of bulk concentration.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.05a
• /
• pp.5-8
• /
• 2005

Sound absorbing performance is affected by porosity and continuity of void, therefore it is important to maintain stabilization of foam and to analyze properties of void pore in hardened state. The purpose of this study is to analyze the sound absorption properties and void characteristic of foamed concrete according to dilution ratio of foaming agent. The results of this experiment were as follows. It is determined that an increase in total and continuous void ratio is achieved by increasing of dilution ratio, and a shorter absorbing time was exhibited at a higher continuous void ratio. When the average void size of foamed concrete was below 1.5mm, the tendency of sound absorption coefficient compared with general sound absorber was appeared similarly.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.5
• /
• pp.733-741
• /
• 2002

If a part of the poor solution from the absorber outlet is recirculated to the absorber inlet, the solution temperature at the solution spray pump can be reduced, and the solution flow rate in the absorber is increased. We have performed the experiments on the influences of the absorption chiller performance according to the ratio of the recirculation, defined as the ratio of the recirculation flow rate to the total solution flow rate at the absorber outlet. As increasing the ratio of the recirculation, the absorption capacity of the solution can be deteriorated. On the other hand, due to the increasing flow rate, the heat transfer rate can be enhanced. As a result, the performance of the absorber and the cooling capacity of the absorption chiller have nothing to do with the recirculation ratio, and the lifetime of the spray pump will be maintained.

• Transactions of the Korean hydrogen and new energy society
• /
• v.14 no.3
• /
• pp.207-216
• /
• 2003

By using the electrochemical method, the relation between the deformation and the geometrical shape, and the effect of cold work on hydrogen absorption-desorption cycling in palladium were investigated, In order to study this problem, four kinds of the Pd specimens used were plates and bars as cold worked and annealed states. As results, it is found that the deformation of thickness direction in the palladium plates increased whereas other lateral directions decreased. But the palladium bars showed the same deformation ratio in all directions because of uniform distribution of the $\beta$ phase. Grains in the plate specimens were greatly deformed after hydrogenation cycling whereas grains in the bar specimens were pulverized. Also, deterioration of the hydrogen absorption rate of the bar specimen was larger than the plate specimen. And the effect of cold work on hydrogen absorption capacity was relatively small.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.29 no.3
• /
• pp.60-68
• /
• 1997

To develop paper coating technology for preventing print mottling, which is recognized as the most common printing problems in using coated papers, ink absorption properties of various coated papers were examined by employing K 8T N and Croda ink absorption tests. The influences of pigment compositions, coat weights and drying methods on these ink absorption properties were examined, and then the variations of ink absorption ratio were analyzed and discussed. It is demonstrated that the variation of Croda ink absorption ratio induced by coat weight variation can be utilized most succesfully to predict print mottling propensity of coating formulations. A systematic analysis approach was suggested that can be employed in the development of the most desirable coating color formulation to achieve target optical properties with the least print mottling.