• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.6
• /
• pp.28-34
• /
• 1999

We fabricated a planar ultra-violet photodetector whose ohmic and schottky contacts were respectively formed with evaporated Al and Pt on the GaN layer. To examine the applicability of the device to the UV sensor, we investigated its electrical and optical characteristics. The GaN layer on the sapphire waver had $7.8{\times}10^{16}cm^{-3}$ of doping concentnation and the $138 cm^2/V{\cdot}s$ of electron mobility and it absorbed the spectrum of the light below 325 nm wavelength. It had the responsivity of 2.8 A/W of at 325 nm, and the signal to noise ratio(SNR) of $4{\times}10^4$, and the noise equivalent power(NEP) of $3.5{\times}10^9$W under 5 V reverse bias. These results confirmed that the GaN schottky diode had a solar blind properly when it was applied to the UV photodetector.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.26 no.3
• /
• pp.390-396
• /
• 1997

Meju is a basis for manufacturing Kanjang, Meju was traditionally prepared at home by different types of process depending on the regional area. It is necessary to standardize and simplify the process of Meju-preparation for Kanjang of good quality. For these purposes, the process of Meju and Kangjang making as well as analysis of commercial Kanjang, were compared. Generally, traditional Meju was prepared by steeping and dehulling the whole soybean. After steeping for 24hr. soybean absorbed water up to 110~120% of its weight. The soaked soybeans were steamed for 2hr. and cooled to 5$0^{\circ}C$. Cooked soybeans were crushed down to the size of 10~15 mesh and molded. Molded soybeans were dried for 2 days in the air, hung up by rice straw and fermented for 20~30 days under natural environmental condition. On the other hand, commercial soybean koji was made of defatted soybean. Defatted soybeans were steeped in water and steamed for 15~30min at 0.7~1.2 kg/$\textrm{cm}^2$. Steamed and defatted soybean was cooled to 4$0^{\circ}C$. Separately, wheat power was roasted at 200~30$0^{\circ}C$ by wheat roaster. Mixture of steamed defatted soybean and roasted wheat powder (5/5 to 7/3) were inoculated with 0.1~0.2% Aspergillus sojae and incubated for 2 days at 3$0^{\circ}C$ with occasional stirring. Chemical analysis showed that traditional soy sauces contained the following composition: NaCl, 20.12~25.42%; total nitrogen, 0.64~0.91%; pure extract, 9.47~11.20%; color, 2.34~4.01; pH, 4.92~5.12. Commercial products contained: NaCl, 15.20~17.19%; total nitrogen, 1.25~1.40%; pure extract, 18.17~21.47%; color, 5.41~21.12; pH, 4.51~4.66 and ethalnol. 2.97~3.12%. Organoleptic test on taste, color and flavor of traditional and commercial soysauce indicated that most of the consumers prefer commercial products to traditional products. Preferrable formulation of Kanjang based on organoleptic test of soy sauces was assumed as containing; NaCl, 16.0%; total nitrogen, 1.40%; pure extract, 19.97%; color, 12.98; pH, 4.61 and ethanol, 2.96.

• Journal of Dairy Science and Biotechnology
• /
• v.28 no.2
• /
• pp.13-18
• /
• 2010

Electron Spin Resonance (ESR) spectroscopy has been used to detect the presence of radiation-induced free radicals in biological samples since the mid 1950s and to irradiate foods containing cellulose, crystalline sugar, and bone. Therefore, we analyzed the ESR spectrum of irradiated infant formula and its ingredients in this study. Samples were irradiated with 2 different radiation sources of $^{60}Co$ gamma rays and electron beams (EBs), and the absorbed doses were 0, 1, 3, 5, and 7 kGy. ESR measurements were performed under normal atmospheric conditions using a JEOL JES-FA100 spectrometer equipped with an X-band bridge. Irradiated infant formula showed anunsymmetrical spectrum ($g_1$=2.0050, $g_2$=2.0006); in contrast, non-irradiated samples showed asymmetrical spectrum. The ingredients of irradiated samples showed a multi-component ESR signal in glucose and lactose and a singlet-type spectrum in milk powder (g=2.0050). $R^2$ of the dose-response curve showed a fine linearity of over 0.95 across the entire sample. We also compared the spectra of identical samples irradiated with $^{60}Co$ gamma rays and EBs, because EBs can be used for food irradiation in foreign countries, although this is not permitted in Korea. However, we could not find any significant differences according to the types of radiation source. Thus, ESR spectroscopy can be used to detect irradiated infant formula and several types of primary ingredients in this formula.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.2
• /
• pp.149-158
• /
• 1998

The SAR patterns of biological objects contacted with coaxial waveguide antennal has been investigated, in which the biological object was modeled by a homogeneous and four-layered lossy human body. We derived the finite-difference time-domain(FDTD) algorithm and equation of MUR and generalized perfectly matched layer(GPML) ABCs in cylindrical coordination. The coupling between coaxial waveguide antenna and a biological object was analyzed by use of MUR and GPML ABCs in the FDTD method to obtain the absorbed power patterns in the media. The specific absorption rates (SAR) distribution which was corresponding to the temperature distribution was calculated in each region by use of the steady-state response in the FDTD method. The SAR patterns of the FDTD method using MUR absorbing boundary conditions(ABCs) was compared with those of the FDTD method using GPML ABCs. The comparison exhibits that the penetration depth of the SAR patterns using MUR ABCs is deeper than that of the SAR patterns using GPML ABCs because of loss in free space. However, the spread in the lateral directions of the SAR patterns using GPML ABCs is smaller than of the SAR patterns using MUR ABCs.

• Korean Journal of Optics and Photonics
• /
• v.16 no.6
• /
• pp.535-541
• /
• 2005

We report on the development of a passively mode-locked near-infrared femtosecond laser with Cr:YAG crystal that operates near room temperature. The laser wavelength could easily be tuned by using only the internal prism pair over 110 nm from 1400 nm to 1510 nm in cw and over about 30 nm in mode-locked operation, respectively Maximum cw output powers of 810 mW were obtained with $1.5 \%$ output coupler for absorbed pump powers of 7.6 W. For compensation of the internal group velocity dispersion, an IR graded prism pair was used. The Cr:YAG laser delivered nearly Fourier-transform limited pulses with a pulse duration as short as 64 fs at 100 MHz repetition rate. In the mode-locked regime, the laser was operating at 1510 nm with a spectral bandwidth of 44 nm. In order to avoid unstable mode-locking and power instabilities, self-built tubes were inserted into the beam path in the resonator and purged with N2 gas. Finally, output powers of the Cr:YAG laser were optimized to 250 mW fer long time stable mode-locked operation.

• Korean Journal of Optics and Photonics
• /
• v.28 no.4
• /
• pp.153-157
• /
• 2017

An infrared camera and laser common-path optical system is applied to DIRCM (directional infrared countermeasures), to increase boresighting accuracy and decrease weight. Thermal effects of a laser beam in a common-path optical system are analyzed and evaluated, to predict any degradation in image quality. A laser beam with high energy density is absorbed by and heats the optical components, and then the surface temperature of the optical components increases. The heated optical components of the common-path optical system decrease system transmittance, which can degrade image quality. For analysis, the assumed simulation condition is that the laser is incident for 10 seconds on the mirror (aluminum, silica glass, silicon) and lens (sapphire, zinc selenide, silicon, germanium) materials, and the surface temperature distribution of each material is calculated. The wavelength of the laser beam is $4{\mu}m$ and its output power is 3 W. According to the results of the calculations, the surface temperature of silica glass for the mirror material and sapphire for the lens material is higher than for other materials; the main reason for the temperature increase is the absorption coefficient and thermal conductivity of the material. Consequently, materials for the optical components with high thermal conductivity and low absorption coefficient can reduce the image-quality degradation due to laser-beam thermal effects in an infrared camera and laser common-path optical system.

• Journal of Digital Convergence
• /
• v.13 no.9
• /
• pp.351-359
• /
• 2015

This convergence study analyzed the effectiveness of digital radiography system of copper(Cu) filter in the added filtration for the removal of lower energy radiation through dose and image evaluation. We were analyzed from April to June 2015 result of the examination. Cu filter was applied to each non, 0.1, 0.2, 0.3 mm according to change of kV and mAs and doses were evaluated. Image quality was evaluated by PSNR, MAE, MSE, CNR, SNR and qualitative analysis was performed by seven items for resolution and contrast from chest x-ray criteria of national cancer checkup. The absorbed doses with Cu were lowered by 16-88 % than non-filter but the gaps decreased as kV increased. PSNR were over 30 dB and all significant and CNR and SNR were superior with non-filter but in the qualitative analysis, there were different statistical significant according to each item. The score of 0.1 mm filter was high at pulmonary blood vessel observation and in the 0.3 mm Cu, there were no statistical signigicant except high density and full of air portion. Cu filter can improve image quality with lower radiation dose using better radiation quality and correction power at digital radiography system.

• Korean Journal of Soil Science and Fertilizer
• /
• v.39 no.5
• /
• pp.298-302
• /
• 2006

This study was carried out to establish low-input fertilization and seeding technique using the simultaneous with seeding and fertilizer application machine and band spotty applicator which were manufactured for experiment during cultivation of mulching for peanut(Arachis hypogaea L.). The labor hour for seeding by simultaneous with seeding and fertilizing machine was appeared over 90% reduction effect compared with control plot($17.3hr\;10a^{-1}$). In band spotty fertilization plots, the emergence date was delayed about 4 days and the seedling stand rate was decreased 11~18% compared with control plot(man power). The content of total nitrogen of soil after experiment was increased while the contents of organic matter, available phosphate and exchangeable potassium were decreased than before experiment. The content of nitrogen forming nitrate was increased in band spotty fertilization(BSF) plots by increasing the amount of applied fertilizer from early growth stage till the middle growth stage. Growth rate was increased in band spotty fertilization plots and the absorbed amount of phosphate and potassium for peanut were increased in 70% band spotty fertilization plot compared with control plot. Yield of peanut was increased 70% in band spotty fertilization plot due to high pod kernel ratio and ripened pod rate compared with control plot($3,150kg\;ha^{-1}$). It was found that 70% band spotty fertilization was more effective as fertilization method to reduce both environmental pollution and chemical nitrogen fertilizer in plastic film mulching cultivation of peanut.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.47 no.3
• /
• pp.227-235
• /
• 2021

In this study, we have prepared pure planar-type ZnO and calamine powder containing both ZnO and Fe₂O₃ components as a raw material for cosmetics with UV and blue band blocking functions. The planar-type ZnO ceramic powder having a high aspect ratio in the range of 20:1 to 50:1 was synthesized by precipitation method in a zinc acetate and sodium citrate mixed solution with the electrolyte obtained by power generation with a zinc-air battery. The content of Fe₂O₃ in the artificial calamine ceramic powder could be increased by increasing the amount of iron chloride solution added, and in this case, some of the blue region of visible light and ultraviolet light were remarkably absorbed. When potassium acetate was added, the decomposition of the Zn(OH)₄^2- anion in the solution was promoted to facilitate the growth of ZnO crystal in the form of a barrier wall in the vertical direction on the (0001) plane, which could increase UV absorption by providing more opportunities. By controlling the amount of iron chloride solution and potassium acetate solution added, the composition and shape of the thin film plate-shaped artificial calamine ceramic powder can be optimized, and when applied to cosmetic formulations, the light transmittance of the blue region can be greatly reduced.

• 한국사회정책
• /
• v.25 no.1
• /
• pp.195-229
• /
• 2018

This study has examined how the welfare system has changed as it has passed through the most controversial period in Korean modern history. The welfare system has changed in a way that adapts to the need for export-led economic growth. Industrialization centered on light industry, which started in the mid-1960s, absorbed the labor force that existed in the rural areas and commodified them, thereby creating a momentum for Korean society to get out of poverty. However, the public de-commodification, ie social security system, adapted to the commodification of the labor force has been institutionalized only in a very limited area and people. Indeed, the de-commodification system was confined to the area directly linked to the reproduction of the labor force. Even so, the target was very limited in the abundance of labor in rural areas. Compulsory medical insurance was rejected because of corporate burden, and industrial accidents insurance was introduced centering on large-scale workplaces. As the Korean economy began to move from the light industry to the heavy industry in the 1970s, the commodificated labor force changed from a low skilled labor force to a skilled male labor force. It is at this time that dual structures have begun to be created between workers employed in export-oriented large enterprises and workers employed in domestic-oriented SMEs. Therefore, the system of de-commodification that supports the reproduction of labor power in response to social risks has also been institutionalized centering on large-scale workplaces.