• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1436-1441
• /
• 2004

Achieving the maximum blasting efficiency with minimum abrasive consumption is a critical concern in surface preparation stage of shipbuilding and offshore industry. Increasing the abrasive flow rate beyond the optimum point results in a major reduction in productivity even though the amount of abrasive used is larger. So, this study is intend to find out the optimum abrasive-to-air mixing ratio which can make a significant improvement in blasting efficiency and remarkably reduce the amount of abrasive used. From the test results, it can be identified that as the abrasive feeding rate is increased linearly, blasting efficiency is increased to a maximum point and then gradually decreased in the form of a bell-shaped.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.7
• /
• pp.79-86
• /
• 2010

The environment-friendly abrasive materials of starch series has a wide range of application value such as deburring of plastic injection products, paint exfoliation and surface treatment of painted products and polishing, etc. In this study, an experiment of paint exfoliation was performed by using the environment-friendly abrasive materials made of cheap starch, and its performance was reviewed. By adjusting the grit size of abrasive materials, nozzle pressure, nozzle feed and number of nozzle repetition, paint could be exfoliated effectively. In this experiment, it was found that the most suitable condition was grit size 0.75~1.0 mm, nozzle pressure 0.4 MPa, nozzle feed 5 mm/min and number of processing repetition 2 times.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1185-1189
• /
• 2007

In this paper, to improve the efficiency of pressurized pneumatic grit conveying for ship block open blasting process. Pressurized pneumatic grit conveying is defined as the transportation of grit(abrasive) in a compressed air flow. Total Pressure loss in flexible hose for pneumatic conveying is sum of pressure losses due to gas and grit and needle type pressure transmitter for measured pressure loss. haracteristics of grit open blasting by pneumatic conveying were studied experimentally. Studies variables were blasting nozzle ID, length and ID of flexible hose, grit flow rate, flow rate and pressure of transport air. It was experimentally proved that optimal open blasting condition and cost effective operation regarding grit blasting, obtaining a high qulity surface preparation(Sa $2^{\frac{1}{2}}$).

• Journal of Technologic Dentistry
• /
• v.46 no.3
• /
• pp.107-113
• /
• 2024

Purpose: This study aimed to develop dental alumina ceramic dressers, evaluate their abrasive wear characteristics based on particle size, and identify dental dressers with optimal particle size and performance. Methods: Commercial ceramic dressers (n=5) were selected as the control group, whereas alumina ceramic dressers with 80-grit and 120-grit particles were fabricated as the experimental groups (n=5 each). Prepared specimens were assessed for surface roughness, wear resistance, and abrasiveness against a wear-inducing element (SUS304 stainless steel ball). Means and standard deviations were calculated for each test. Statistical analysis was performed using the Kruskal-Wallis H test with Bonferroni correction (α=0.05) via SPSS Statistics ver. 23.0 (IBM). Results: Surface roughness was highest in the 80-grit group (22.734±1.308 ㎛), followed by 120-grit group (21.804±0.785 ㎛), and lowest in control group (15.782±0.223 ㎛). Wear resistance was greatest in 120-grit group (0.007±0.002 g), followed by the 80-grit group (0.007±0.004 g), and lowest in the control group (0.370±0.010 g). Furthermore, abrasiveness against the wear-inducing element (SUS304 stainless steel ball) was highest in 120-grit group (0.017±0.003 g), followed by the 80-grit group (0.015±0.003 g), and lowest in control group (0.010±0.001 g). Conclusion: Based on the combined results of surface roughness, wear resistance, and abrasiveness against a wear-inducing element, the newly developed alumina ceramic dressers show promise for clinical application.

• Journal of Biosystems Engineering
• /
• v.8 no.1
• /
• pp.17-29
• /
• 1983

The milling process is considered as causing one of the greatest grain losses among all the processes in rice post-production. Major source of grain losses in the rice milling is considered as the whitening process. This study was attempted to develop an abrasive-type whitener, the whitening chamber of which being supplied by jet-air evenly and continuously. To investigate the milling performance by the new whitener, three kind of emery-stone grit(#36, #41, and #46), and three levels of rotational speed of emery stone roller (950, 1070, and 1200 rpm) were tested. The jet-air abrasive-type whitener was also compared with the conventional abrasive-type having no jet-air blower in terms of their milling performance. In addition, the effect of different combinations of sequential uses of the abrasive- and friction-type whiteners on the milling performance was also experimentally evaluated. The results of this study are summarized as follows; 1. In general, the whitening system combined with the abrasive type whitener with jet-air supply, which was newly designed, and the existing jet-air friction type whiteners produces more milled- and head-rice by about 0.3% points and 2.8% points, respectively than the system combined with the existing abrasive type without the jet-air supply under the same operational conditions. The former also consumed less electricity by 0.024 KwH per 100kg of milled rice production and gave more milling capacity by about 35 kg/hr. As compared with the conventional whitening system consisting of jet-air friction type whiteners only, the former yielded more milled- and head-rice by 1.5% points and 4.4% points, respectively. 2. The abrasive roller having 46 grit emery was better than the roller having 36 grit in aspects of milling performance and machine efficiency, in general. 3. With regard to the effect of combination method of abrasive type and friction type whiteners, one pass in abrasive type plus three passes in friction type gave better milling performance and energy efficiency than the two passes in abrasive type plus two passes in friction type regardless of the designs of the emery stone rollers. 4. The increase in rotational speed of the emery stone roller from 950 rpm to 1200 rpm presented negative effects on milled and head-rice yields and machine efficiency, but slightly positive effect on milling capacity.

• Journal of the Speleological Society of Korea
• /
• no.70
• /
• pp.45-50
• /
• 2006

The magnetic polishing is the useful method to finish using magnetic power of magnet. This method is one of precision polishing techniques and has an aim of the clean technology using for the pure of gas and inside of the clean pipe for transportation. The magnetic abrasive polishing method is not so common for machine that it is not spreaded widely. There are rarely researcher in this field because of non-effectiveness of magnetic abrasive. Therefore, in this paper deals with development of the magnetic abrasive using worthless mineral. In this development, abrasive grain WA and GC used to resin bond fabricated low temperature. And magnetic material was fabricated from the worthless mineral which were closed into 200 mesh grit type. The XRD analysis result show that only WA and GC abrasive and worthless mineral crystal peaks detected which explains resin bond was not any more chemical reaction. From SEM analysis it is found that WA and GC abrasive and worthless mineral were strong bonding with each other by bond.

• Korean Journal of Materials Research
• /
• v.9 no.2
• /
• pp.111-116
• /
• 1999

The microstructure of vitreous bonded abrasives, which are used as the essential materials in the precise grinding, was investigated theoretically using two particle model. In this paper, a general equation applicable for a case in which there is a gap between abrasive grits is suggested. As a result, it was known that both the volume ratio of grit to glassy bond(V\ulcorner/V\ulcorner) and porosity(V\ulcorner) are the function of $\alpha$(the ratio of distance between grit to diameter of grit) and $\theta$(the angle from the center of pore to that of grit). Because the value $\alpha$ and $\theta$ can be get easily by using these suggested equations, the microstructure could be explained quantitatively. Also the raised error with the increasing amount of bond was modified by the simple assumption. As a result, in that case, both V\ulcorner/V\ulcorner and V\ulcorner were known to be the function of $\alpha$ and $\theta$(the ratio diameter of pore to that of grit).

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1442-1447
• /
• 2004

A significant amount of labor hour is being spent for clean up spent abrasives after blasting. So, for improving the efficiency of abrasive(grit) recovery process which acts as the neck of a battle in preceding coating stage, it was established the theoretical background for pneumatic transport technology in the abrasive recovery system as well as experimentally evaluated the effect of design parameters such as flow pattern, saltation velocity and pressure drop on the efficiency of the abrasive recovery system. And, by optimizing the operating parameter such as the length and diameter of suction hose, specification of recovery device, recovery mouth and hose connection method, a method which can dramatical1y increase the efficiency of abrasive recovery system, is derived.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.10a
• /
• pp.99-100
• /
• 2009

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.6
• /
• pp.45-51
• /
• 1996

Silicon wafers are required to be finished under the roughness of nanometer order for the subsequent chip fabrication processes. Recently, the finish grinding techniques have been researched for the improvement of accuracy and surface roughness simultaneously. Among them, the grinding technique using fine abrasive has been known as an easily accessible method. However, the manufacture of the fine grit grinding wheel has been very difficult because of the coherence of the grits. In this paper, the development of the ultrafine grit silica($SiO_2$) grinding wheel by the combination of the binder coating and the vacuum forming techniques is reported. And, the mechanochemical removal effects of the grinding conditions are discussed. Finally, a successful result of Ra O.4nm. Rmax 4nm in the ground surface roughness of a 6 inch silicon wafer was achieved.