• 한국전기전자재료학회논문지
• /
• 제36권4호
• /
• pp.391-396
• /
• 2023

Recently, as power and electronic devices have increased in frequency and capacity, it has become a major concern to protect electronic circuits and electronic components used in these devices from abnormal voltages such as various surges and pulse noise. To respond to variously rated voltages applied to power electronic devices, the rated voltages of various varistors can be obtained by controlling the size of internal particles of the varistor or controlling the number of layers of the varistor. During bonding, the problem of unbalanced thermal runaway occurring between the electrode and the varistor interface causes degradation of the varistor and shortens its life of the varistor. In this study, to solve the problem of unbalanced heat distribution of stacked varistors to adjust the operating voltage, the contents of the ZnO-based varistor composition were 96 wt% ZnO, 1 mol% Sb₂O₃, 1 mol% Bi₂O₃, 0.5 mol% CoO, 0.5 mol% MnO, and 1 mol% TiO₂. A multi-layered ZnO varistor was modeled by bonding a single varistor with a composition in three layers according to the operating voltage. The thermal distribution of the triple-layered ZnO varistor was analyzed for the thermal runaway phenomenon that occurred during varistor operation using the finite element method according to Comsol 5.2.

• Journal of Electrical Engineering and Technology
• /
• 제10권6호
• /
• pp.2256-2261
• /
• 2015

In the power plant using high temperature fuel cells such as Molten Carbonate Fuel Cell(MCFC), and Solid Oxide Fuel Cell(SOFC), the generated electric power per area of power generation facilities is much higher than any other renewable energy sources. - High temperature fuel cell systems are capable of operating at MW rated power output. - It also has a feature that is short for length of the line for connecting the interior of the generation facilities. In normal condition, these points are advantages for voltage drops or power losses. However, in abnormal condition such as fault occurrence in electrical system, the fault currents are increased, because of the small impedance of the short length of power cable. Commonly, to minimize the thermal-mechanical stresses on the stack and increase the systems reliability, we divided the power plant configuration to several banks for parallel operation. However, when a fault occurs in the parallel operation system of power main transformer, the fault currents might exceed the interruption capacity of protective devices. In fact, although the internal voltage level of the fuel cell power plant is the voltage level of distribution systems, we should install the circuit breakers for transmission systems due to fault current. To resolve these problems, the SFCL has been studied as one of the noticeable devices. Therefore, we analyzed the effect of application of the SFCL on bus tie in a fuel cell power plants system using PSCAD/EMTDC.

• 전력전자학회논문지
• /
• 제12권1호
• /
• pp.9-18
• /
• 2007

본 논문에서는 120도 통전방식의 영구자석 매입형 전동기의 센서리스 제어에 있어서 회전자의 위치를 검출하기 위하여 사용되는 비통전상의 단자전압에 대한 분석을 행한다. 본 연구에서 모터의 비통전상의 단자전압으로부터 얻어지는 위치 정보가 실제의 회전자 위치보다 앞서 있음을 보이며, 이러한 위치 검지 오차에 대한 정량적 분석 및 제어시스템의 모델링을 행한다. 시뮬레이션 및 실험 결과는 제안한 모델링 및 위치 오차의 정량적 분석이 타당함을 보여준다. 또한, 위치 검지 오차에 의해 진상각이 과다하게 인가됨으로 인해 발생하는 이상전류 현상을 분석하며, 이러한 이상전류를 제거하기 위해서는 제어기에서 인가하는 진상각은 속도 및 부하 증가시 감소해야함을 제시한다.

• 전기학회논문지
• /
• 제62권11호
• /
• pp.1604-1609
• /
• 2013

When the ground fault on the power side occurs on distribution system interconnected with distributed generations, the abnormal current is generated in the neutral conductor by the connection type and the iron core structure of transformers for the interconnection of distributed power supplies due to the unbalanced voltage of the system, and subsequently the false operation of the protective relay on the load side occurs. Herein, this paper proposes the method to correct errors in the phase current to prevent the false operation of the protective relay by applying p-q theory and presents the simulation result of the error correction algorithm using PSCAD/EMTDC.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제11권3호
• /
• pp.198-206
• /
• 2011

This paper presents a new programmable compensation circuit (PCC) for a System-on-Chip (SoC). The PCC is integrated with $0.18-{\mu}m$ BiCMOS SiGe technology. It consists of RF Design-for-Testability (DFT) circuit, Resistor Array Bank (RAB) and digital signal processor (DSP). To verify performance of the PCC we built a 5-GHz low noise amplifier (LNA) with an on-chip RAB using the same technology. Proposed circuit helps it to provide DC output voltages, hence, making the RF system chain automatic. It automatically adjusts performance of an LNA with the processor in the SoC when it goes out of the normal range of operation. The PCC also compensates abnormal operation due to the unusual PVT (Process, Voltage and Thermal) variations in RF circuits.

• Journal of Electrical Engineering and Technology
• /
• 제12권1호
• /
• pp.396-401
• /
• 2017

In this paper, a device to analyze gait pattern was developed by using a 2-axis acceleration sensor attached to the foot. The 1st low-pass filter was adapted to limit the frequency band up to 5 Hz. An algorithm to detect the peak value exceeding the threshold voltage of an X-axis acceleration sensor and a Z-axis acceleration sensor was developed and normal and abnormal walking patterns were thus differentiated. Also, MCU and Bluetooth were combined to transfer the data to other MCUs to display on an LCD; the size of the device could then be reduced. The new algorithm and the device allowed the individual walking patterns to be easily measured at a low cost and with less restriction on activities compared to conventional multiple pressure sensors or motion camera system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1991년도 추계학술대회 논문집 학회본부
• /
• pp.71-74
• /
• 1991

This paper is described an expert system which performs the network reconfiguration in order to operate distribution systems optimally using heuristic rules. The proposed network reconfiguration is able to not only eliminate abnormal states such as overload of transformers/lines and low voltage violation, but also achieve minimum power loss and optimum load balancing under normal states. In order to apply the network reconfiguration efficiently, an expert system is adopted a best-first tree searching strategy on the basis of heuristics, and is implemented in AI language Turbo PROLOG. Several examples are used to illustrate concepts described above.

• 전기학회논문지P
• /
• 제59권1호
• /
• pp.71-76
• /
• 2010

This paper is focused on implementing a real-time data acquisition system that checks power facility status by applying network based technology to Urban Transit substation power facilities and the results of its on-field tests. This system is composed of a sensor part, a measurement part, a transceiver part, a host computer, and a power source part. The system is designed to collect, save, analyze, and display the online state power facility AI (Analog Input). This system measures voltage and current from positive feeders and negative feeders where it is possible to check abnormalities of the substation‘s main power facilities. By monitoring abnormal data of the Urban Transit power facilities real-time and analyzing stored data, establishing procedures of optimized maintenance is possible.

• 조명전기설비학회논문지
• /
• 제21권7호
• /
• pp.1-5
• /
• 2007

형광램프를 오랜 기간 사용하게 되면 전극에서 열 전자 방출을 돕는 보조 물질이 램프 외벽으로 흡수되어 램프 점등 조건 및 정상 상태 조건이 변화하게 된다. 이러한 경우를 오랜 시간 방치한다면 램프 전극에서 과도한 열이 발생하게 되어 등 기구 소켓을 녹이는 안전사고가 발생할 가능성이 크다. 본 논문은 형광램프 수명 말기에 나타나는 현상(정류 효과)을 검출하고, 이로부터 안정기를 보호하기 위한 방법을 제시하였다.

• 한국표면공학회지
• /
• 제30권1호
• /
• pp.44-56
• /
• 1997

Influence of electrochemical etching conditions on capacitance gain of aluminium electrolytic on capacitor foil has been investigated by etching cubic textured high purity aluminum foil in dilute hydrochloric acid. Uniformly distributed etch pit tunnels on aluminum surface have been obtained by pretreatment aluminium foil in 10% NaOH solution for 5 minutes followed by electrochemical etching. Electrostatic capacitance of etched aluminium foil anodized to high voltage increased with the increase of current density, total charge, temperature and concentration of electrolyte up to maximum CV-value and then deceased. Election optical observation of the etched foil revealed that the density of etch of etch pits increased with the increase of current density and concentration of electrolyte. this increase of etch pit density enlarged of the increase of capacitance. However, abnormal high current density and high electrolyte concentration induced the local dissolution of the foil surface which resulted the decrease of foil capacitance.