• 한국레이저가공학회지
• /
• 제17권1호
• /
• pp.7-12
• /
• 2014

The dissimilar welding between magnesium alloy and steel sheet was required in automobile industry to increase the strength of the dissimilar joints. Laser brazing is one of the good joining processes for Mg- steel dissimilar joint. In this study, AZ31 magnesium alloy and Zn coated steel dissimilar joint was brazed using diode direct laser with Mg600 filler wire and Superior #21 flux. The wetting of Mg filler wire on Zn coating was very good because of the formation of eutectic phase with low melting temperature. The strength of the brazed joint between AZ31 magnesium alloy and Zn coated steel was 131.3N/mm. The fracture occurred at brazement.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 제5회 박판성형 SYMPOSIUM
• /
• pp.99-102
• /
• 2006

In the present study, the blow forming characteristics of AZ31 sheet was investigated to test the feasibility of the practical application of wrought Mg alloys. Mg alloys have drawn a huge attention in the field of transportation and consumer electronics industries since it is the lightest alloy which could be industrially applicable. Most Mg alloy components have been fabricated by casting method. However, there have been a lot of research activities on the wrought alloys and their plastic forming process recently. Shallow cups for the small electronics cases have been stamped with warm die system. However, some technical issues will challenge Mg forming when large parts are considered with warm die system over $200^{\circ}C$. Most of all, thermal expansion of die system will deteriorate a die accuracy. On the other hand, blow forming does not have a problem with inaccuracy with die system. In this study, tensile tests were followed by blow forming at various temperature and pressure. AZ31 sheet showed a superplastic deformation behavior with extensive grain boundary sliding at the temperature above $300^{\circ}C$. However, the deformation behavior was likely to differ depending on stress condition.

• 소성∙가공
• /
• 제23권8호
• /
• pp.495-500
• /
• 2014

Magnesium alloys are currently expected to be widely used for weight reduction of cars and as high efficient materials in the automotive and electronics industries. Although the specific strength of magnesium is excellent, it cannot be easily formed at room temperature due to its HCP structure. However in order to improve the formability of magnesium, it is necessary to investigate its formability in the warm temperature range. In the current study, the aim was to add to the magnesium property database so that the mass production of a magnesium car body can be accomplished. Warm tensile tests were conducted and the forming limit diagram was determined to confirm formability characteristics of magnesium AZ31B alloy sheet. In addition the bending formability and the magnesium damping capacity were evaluated for AZ31B and compared to SPRC440E which is a sheet steel used for car bodies.

• 소성∙가공
• /
• 제17권7호
• /
• pp.466-472
• /
• 2008

In this paper, tension tests and formability tests are performed to construct a database related to mechanical properties and the formability of the AZ31B Mg alloy sheet. A forming test with a hemi-spherical punch is conducted at varying temperatures to establish a forming limit diagram. In order to verify the applicability of the analysis using the conventional flow hardening model, a finite element analysis is performed on the hemi-spherical punch forming process and the results are compared with experimental ones. The study investigates problems involving a computational analysis that does not consider flow softening of the magnesium alloy at elevated temperatures.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.366-369
• /
• 2008

In this paper, tension tests and formability tests are performed to construct a database related to mechanical properties and the formability of the AZ31B Mg alloy sheet. A forming test with a hemi-spherical punch is conducted at varying temperatures to establish a forming limit diagram. In order to verify the applicability of the analysis using the conventional flow hardening model, a finite element analysis is performed on the hemi-spherical punch forming process and the results are compared with experimental ones. The study investigates problems involving a computational analysis that does not consider flow softening of the magnesium alloy at elevated temperatures.

• 한국기계가공학회지
• /
• 제3권1호
• /
• pp.52-58
• /
• 2004

The material used is a commercial magnesium based alloy AZ31(Mg-3Al-1Zn)sheet with a thickness of 1.0mm. Uniaxial tension tests at warm temperature were carried out to investigate the material characteristics of K, m, and n. A warm drawing process with a local heating and cooling technique was developed to improve formability in this study with results of uniaxial tension tests because it is very difficult for Mg alloy to deform at room temperature by the conventional method. The die and blank holder were heated up, while the punch was water-cooled during deformation. FE simulations considering heat transfer were executed with Mg alloy to investigate the Improvement of deep drawability. For the assessment of improvement those were compare with the results of no considering heat transfer and room temperature.

• 열처리공학회지
• /
• 제21권6호
• /
• pp.293-299
• /
• 2008

In order to provide with fundamental data of the wrought Mg alloy for press forging, the effect of annealing temperature on the microstructure, texture development and tensile properties is studied in a commercial AZ31B Mg alloy sheet. Basal texture i.e. $(0001){\pm}5^{\circ}$[21$\bar{3}$0] is developed in a commercial AZ31B Mg sheet, and the texture is not changed considerably by annealing over $400^{\circ}C{\times}30min$, while (10$\bar{3}$0) component with high intensity can be observed due to abnormal grain growth. When the sheet is tensile-deformed with RD, $45^{\circ}$ and TD directions at room temperature, fracture strains are given by 25.8, 21.4 and 11.9% in the order of RD, $45^{\circ}$ and TD directions, respectively. With increasing annealing temperature up to $450^{\circ}C{\times}30min$, little change in mean grain size can be revealed by annealing below $300^{\circ}C{\times}30min$ but an abnormal grain growth, where some grains become significantly coarser than the rest, occurs by annealing above $400^{\circ}C{\times}30min$. The maximum tensile strain of around 25% is obtained by annealing below $300^{\circ}C{\times}30min$, but it is abruptly decreased to 16% by annealing above $400^{\circ}C{\times}30min$ owing to intergranular fracture of abnormal grown grains.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 추계학술대회논문집
• /
• pp.175-179
• /
• 2004

Since the formability of AZ31 magnesium alloy is not good in room temperature, it is known that high temperature forming is advantageous. However, many studies are necessary to find the proper forming temperature for Mg alloy. In this study, experimental and FEM analysis are performed to investigate the forming temperature for AZ31 sheet. The deep drawing process of square cup is used in forming experiment and FEA. The investigations are performed in three forming temperature, room temperature, $250^{\circ}C\;and\;400^{\circ}C$. The square cup is well formed in $250^{\circ}C$ forming temperature, on the other hand, the crack and failure is presented in corner section in room and $250^{\circ}C$ forming temperature. The main cause is investigated as the effect of hardening range by the experimental and FEM results.

• 소성∙가공
• /
• 제24권6호
• /
• pp.405-410
• /
• 2015

Sheet-forming of Mg alloys is conducted at elevated temperatures (250℃) due to the low formability at room temperature. The high-temperature process often gives rise to surface damage on the alloy (i.e. galling.) In the current study, the frictional characteristics of DLC coating slid against an AZ31 Mg alloy at various temperatures were investigated. The coating has been used widely for low-friction processes. Dry-sliding friction and galling characteristics of an AZ31 Mg alloy (disk), which slid against uncoated and a DLC-coated STD-61 steel (pin), were investigated using a reciprocating-sliding tribometer at room temperature and 250℃. To represent the real sliding phenomena during a sheet metal forming process, single-stroke tests were used (10mm stroke length) rather than a reciprocating long sliding-distance test. The DLC coating suppressed adhesion between the alloy and the tool steel at room temperature, and exhibited a low friction coefficient. However, during sliding at 250℃, severe adhesion occurred between the two surfaces, which resulted in a high friction coefficient and galling.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 춘계학술대회 논문집
• /
• pp.43-46
• /
• 2004

Since Mg alloy has many attractive advantages among the practically used metals, many researchers have been studied to develop useful process and material. However, study for sheet forming has not been a few because of low formability on room temperature. Formability and springback for AZ31 alloy sheet have been studied to develop the cold forming technology. The experimental and FE analysis were performed to analyzed the springback amounts by using a model of our on. A different three materials were used to investigate the effects of material characteristics. The springback amounts of Mg-alloy sheet formed part were larger than that of the other material.