• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.04a
• /
• pp.731-732
• /
• 2011

This paper shows a whole noise quality checking system for the new developed 6th speed automatic transmission manufactured in USA. Due to demand for manufacturing of the high NVH quality transmissions in the mass product line, some special checking system called EOL is adapted. This EOL system is using vibration analysis technologies. Through adapting vibration analysis technologies and functions likewise RMS, Crest Factor, Harmonics, Peak, Band, and Order tracking, various noise problems caused by wear, nick, and deformations could be successfully detected and predicted. Therefore, automatic transmissions manufactured in the USA could get high NVH quality.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.5
• /
• pp.107-114
• /
• 2006

This paper investigates the radiating source of electro-magnetic waves in the cabin of automobile with spark ignition engine. Front seats are very close to the engine room where electro-magnetic waves are expected to be radiating. But front seat area is believed to be a blind zone, which is not affected by radiating electro-magnetic waves, because a bulk board and floor board shield the front seat area. The level and frequency spectrum of electro-magnetic waves are measured at the passenger seat and the engine room. The measured frequency range is $145{\sim}365MHz$. As a results, the level of the electro-magnetic waves of automatic transmission vehicle is greater than -82dBm. The shapes of frequency spectrum of both engine room and passenger seat are look alike. But the level of electro-magnetic waves of manual transmission vehicle is less than -82dBm and the shapes of frequency spectrum of engine room and passenger seat are different to each other. From these results, we can say that any mal-function caused by electro-magnetic waves in the automobile cabin are only possible for automatic transmission vehicle. Also, it is believed that the radiating source of electro-magnetic waves is inside the vehicle. Thus, based on the transmission line theory, this paper presumably concludes that the cables which connect all the components inside a automatic transmission vehicle must be a radiating source of electro-magnetic waves in the cabin.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.10a
• /
• pp.11-16
• /
• 1998

Condition monitoring technique used in the military is JOAP, for which the spectroscopic analysis is applied. However it is known that the technique has some problems in economical and practical point of view. This study introduces a new technique for measuring wear in real time base and applies the technique to a high power semi-automatic transmission. The results show the feasibility by measuring the concentration of ferrous wear particles from the transmission oil.

• Korean Journal of Computational Design and Engineering
• /
• v.12 no.6
• /
• pp.466-471
• /
• 2007

Brackets for an automatic transmission are usually used to connect the transmission with adjacent components in a vehicle. Fillet areas of brackets are one of the most important areas to design the brackets because the areas are easily fractured when the brackets are subjected to external loads. In this study, a new design around the fillet area of the bracket is suggested and improved effects of the proposed design are proved through the comparison of safety factors with the current design. The safety factors are calculated through the fatigue analysis via a commercial code, FEMFAT.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.6
• /
• pp.9-18
• /
• 2000

This study includes noise automatic inspection system for washing machine auto-transmission one of modern home necessary. We effort to find and certificate sound noise source by sound power and sound intensity, and apply to frequency analysis in vibration related sound noise. still more we have been studying to data acquisition and programming for MS VisualBasic version 5.0. System component is below. 1) Pentium PC or data acquisition. 2) DSO for noise acquisition. 3)S/W for comparison and decision. 4) I/F Board for data communication. Wave form data through the DSO are converting to ASCII code data. The ASCII code through binary converting S/W. Finally we will making noise monitoring system and automatic inspection system.

• Korean Journal of Applied Biomechanics
• /
• v.17 no.3
• /
• pp.225-232
• /
• 2007

This work intends to investigate the effects of shift characteristics on the propulsion performance of a manual wheelchair with an automatic transmission. A planetary gear train is employed to generate a two-stage shift automatically, based on the distance traveled from rest. Motion analysis has been performed for measuring kinematic properties of the arm and then the inverse dynamics has been applied for estimating joint forces/torques. Then, a parametric study has been performed to find a set of the shift ratios and the shift intervals for optimizing propulsion performance. Results show that the propulsion performance is closely related to the shift condition. It is found that a short shift interval is desirable for a short distance propulsion. However, an optimum shift interval for a long distance propulsion is inversely proportional to the shift ratio approximately. Consequently, the automatic transmission can greatly lower the joint loadings by the speed reduction, which eventually contribute to prevent joint injuries of wheelchair users.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.427-428
• /
• 2012

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.2
• /
• pp.234-242
• /
• 2002

In this research, a transmission control unit was developed for a wheel loader on the basis of 16-bit microcontroller system. The TCU has the basic functions which include shifting control algorithm, actuation of six proportional solenoid valves, signal conditioning for four speed sensors, remote data monitoring capability with RF-module and duty cycle identification system which could identify the duty cycles from PWM signals. In order to design the control system, the overall transmission structure of the wheel loader was investigated and its characteristics of shifting were analyzed in advance. For the purpose of identifying the existing control algorithm and acquire some information about the shifting performance, the shifting experiments were performed for various shifting conditions with the conventional TCU. From the previous work on the conventional TCU, the shifting scheme was designed with the open-loop control which is based on the experimental data only to verify the feasibility of the developing TCU's shilling capability. The experimental results show comparable shifting characteristics to that of conventional TCU though the tests were performed at restricted shilling conditions. Hence, we could have the confidence for the development of the wheel loader automatic transmission TCU and its shifting quality could be improved with the adoption of appropriate feedback control scheme.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.15 no.1
• /
• pp.30-35
• /
• 2005

An automatic transmission pattern with the fixed standard shift map can provide comfortable shift to driver. However it may be a complain to provide shift by the same shift pattern for driver because the inclination of a driver may be various. Therefore, in this paper, we design the decision module, which can decide the driving style using input to decide the inclination of the driver and driving manner. The goal of this paper is to calibrate the shift map according to the inclination of the driver using the decided driving manner from the proposed module. As a result, the proposed intelligent automatic transmission system can provide a suitable shift point and time to the driver. To verify the performance of the proposed system, the real data that is obtained from the road test will be used.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.5
• /
• pp.639-645
• /
• 2011

Wheel-loader is a construction vehicle for uploading soil or sand into truck and transportation of materials, which requires large driving power and high rotational speed. To improve the working efficiency, the operator has to shift gears and control levers for bucket & boom simultaneously. Therefore, the automatic transmission has been introduced to enhance operator's convenience and enable effective operation. To develop the automatic transmission for the wheel-loader, technologies such as gears and a clutch-pack design and shift algorithm are required for improvement of shift quality. In this paper, the shift algorithm for the wheel-loader was developed and its shift pattern was analyzed. As the shift control is affected by the pressure profile for the clutch control, the shift quality depending on the pressure profile has been evaluated using experiment and simulation model analysis.