• 제어로봇시스템학회논문지
• /
• 제19권1호
• /
• pp.1-9
• /
• 2013

This paper presents a new control algorithm for dynamic control of a unicycle robot. The unicycle robot motion consists of a pitch that is controlled by an in-wheel motor and a roll that is controlled by a reaction wheel pendulum. The unicycle robot doesn't have any actuator for a yaw axis control, which makes the derivation of the dynamics relatively simple. The Euler-Lagrange equation is applied to derive the dynamic equations of the unicycle robot to implement the dynamic speed control of the unicycle robot. To achieve the real time speed control of the unicycle robot, the sliding mode control and LQ regulator are utilized to guarantee the stability while maintaining the desired speed tracking performance. In the roll controller, the sigmoid-function based sliding mode controller has been adopted to minimize the chattering by the switching function. The LQR controller has been implemented for the pitch control to drive the unicycle robot to follow the desired velocity trajectory in real time using the state variables of pitch angle, angular velocity, angle and angular velocity of the wheel. The control performance of the two control systems form a single dynamic model has been demonstrated by the real experiments.

• Journal of Advanced Marine Engineering and Technology
• /
• 제23권3호
• /
• pp.292-299
• /
• 1999

DC motors are widely used in many industrial fields as the actuator of the robot and the driving power motors of the electrical vehicle, Usually in the sensors of DC motors such as the encoder the tachogenerator and the potentiometer etc. are applied, But usage of these sensors results in the increased price and operating cost such that the application of the motors are limitted. To solve this problem another method to construct low cost control system is investigates. In this paper a new speed control method for DC motor is proposed. This method uses motor parameters instead of using speed or position sensors. In this way the angular velocity is estimated by the measure-ment values of the armature voltage and current instead of measuring the sensor signal. This paper presents an alorithm for estimating the angular velocity of DC motor The effectiveness of the proposed method is verified by experimental results. Also the applicability of the proposed method is presented by applying to the velocity contol of a wheeled mobile robot.

• 한국산업융합학회 논문집
• /
• 제19권2호
• /
• pp.81-87
• /
• 2016

This paper presents a new approach to control of stable motion of single wheel driving robot system of a pitch that is controlled by an in-wheel motor and a roll that is controlled by a reaction wheel. This robot doesn'thave any actuator for a yaw axis control, which makes the derivation of the dynamics relatively simple. The Lagrange equations was applied to derive the dynamic equations of the one wheel driving robot to implement the dynamic speed control of the mobile robot. To achieve the real time speed control of the unicycle robot, the sliding mode control and optical regulator are utilized to prove the reliability while maintaining the desired speed tracking performance. In the roll controller, the sigmoid-function based robust controller has been adopted to reduce the vibration by the situation function. The optimal controller has been implemented for the pitch control to drive the unicycle robot to follow the desired velocity trajectory in real time using the state variables of pitch angle, angular velocity, angle and angular velocity of the driving wheel. The control performance of the control systems from a single dynamic model has been illustrated by the real experiments.

• Steel and Composite Structures
• /
• 제23권6호
• /
• pp.691-714
• /
• 2017

Rotating fluid induced vibration and instability of embedded piezoelectric nano-composite separators subjected to magnetic and electric fields is the main contribution of present work. The separator is modeled with cylindrical shell element and the structural damping effects are considered by Kelvin-Voigt model. Single-walled carbon nanotubes (SWCNTs) are used as reinforcement and effective material properties are obtained by mixture rule. The perturbation velocity potential in conjunction with the linearized Bernoulli formula is used for describing the rotating fluid motion. The orthotropic surrounding elastic medium is considered by spring, damper and shear constants. The governing equations are derived on the bases of classical shell theory (CST), first order shear deformation theory (FSDT) and sinusoidal shear deformation theory (SSDT). The nonlinear frequency and critical angular fluid velocity are calculated by differential quadrature method (DQM). The detailed parametric study is conducted, focusing on the combined effects of the external voltage, magnetic field, visco-Pasternak foundation, structural damping and volume percent of SWCNTs on the stability of structure. The numerical results are validated with other published works as well as comparing results obtained by three theories. Numerical results indicate that with increasing volume fraction of SWCNTs, the frequency and critical angular fluid velocity are increased.

• Tribology and Lubricants
• /
• 제35권4호
• /
• pp.244-266
• /
• 2019

The purpose of this study is to estimate the wear volumes of engine journal bearings operating at variable angular velocity of a shaft in the beginning of firing start-up cycle. To do this, first we find the potential region of wear scar on engine journal bearings where the applied bearing load and crank shaft velocity are variable. The potential wear regions are discovered by finding minimum oil film thickness at every crank angle existing below most oil film thickness scaring wear (MOFTSW) obtained based on the concept of the centerline average surface roughness. Then we calculate the wear volume from the wear depth and two wear angles decided by the magnitude of each film thickness lower than MOFTSW at every crank angle. The results show that the expected wear region is located at a few bearing angles after and/or behind the upper center of a big-end bearing and the lower center of a main bearing. And the real wear region is similar to the estimated wear region. Further we find that the wear scar on an engine journal bearing may occur at re-starting time after switch-off of a start motor especially under the condition of high oil temperature.

• International Journal of Internet, Broadcasting and Communication
• /
• 제14권2호
• /
• pp.183-191
• /
• 2022

The purpose of this study, the wearing conditions of functional pressure clothing applied with the thermotherapy device were determined by three types (NW, CW, TCW) and the difference in isokinetic strength, muscle activity around the forearm was investigated and the effects of products mixed with thermotherapy and pressure treatment were verified. Ten men in their 20s were selected as subjects, and all subjects were randomly assigned three wearing conditions, and wrist flexion/extension exercise was performed at 30° and 90° angular velocity in isokinetic equipment. Peak torque, average power, and EMG were measured during exercise in all conditions. For peak torque, CW was significantly highest at velocity of 30°/sec flexion. Average power showed no significant difference by condition. In the angular velocity of 90°/sec, flexion was significantly higher in CW and TCW than in NW. As a result, wearing clothes with pressure effect and heat effect can show high efficiency in high muscle strength development and fast contraction activity during low speed exercise, and it is thought that it can show improvement of exercise ability through efficient recruitment of motor unit.

• 한국운동역학회지
• /
• 제21권5호
• /
• pp.631-638
• /
• 2011

This study had two purposes. The first was to analyze the period of the final record set by the male shot-putters in the IAAF World Championships, Daegu 2011 from the point of view of kinematics. The other was to identify an efficient movement for shot putting based on the analysis. The research used the eight finalists of in the championship as subjects. We analyzed the seven most important kinematic factors in shot putting based on the type of technique: the execution time of the delivery phase, release velocity, release angle, release, center of mass (COM) velocity, and shot trajectories. The analytical results showed the following average figures for the record 12 meters: execution time of the delivery phase: (0.19 s), release height: (2.06 m), release angle: ($34.68^{\circ}$), release velocity: (13.25 m/s), angular velocity of shoulder: ($922.38^{\circ}/s$), and angular velocity of pelvis: ($479.50^{\circ}/s$). Further, the results showed that the highest COM velocity was 2.25 m/s and the shot trajectories were close to a straight line in the release phase.

• 한국지능시스템학회논문지
• /
• 제19권2호
• /
• pp.168-173
• /
• 2009

본 논문은 수중 차의 차속도와 프로펠러 각속도를 추정하는 문제를 다룬다. 계단식 관측기는 측정된 위치 값으로부터 속도값 추정을 위해 사용한다. 고이득 관측기(high-gain observer)에 전형적으로 생기는 전형적인 문제를 없애기 위하여 계단식 구조의 관측기가 설계되었다. 고이득 관측기처럼 시스템 다이나믹스와 파라미터로부터 무관하게 설계할 수 있으며 단순한 구조를 가진다 관측기의 첫 단계에서 출력 값이 추정되고 측정된 출력의 1계 미분 값이 관측기의 두 번째 단계를 통해 추정된다. 또한 출력의 n 번째 미분 값은 관측기의 n+1 번째 단계에서 추정된다. 제안된 관측기가 전체 점근적 안정도를 보장함을 보여준다. 시뮬레이션 결과는 기존의 고이득 관측기에 비해 제안된 관측기가 수중 차의 차속도와 프로펠러 각속도를 더 우수하게 추정함을 보여준다.

• 센서학회지
• /
• 제22권1호
• /
• pp.54-64
• /
• 2013

In this study, we developed a falling recognition system to transmit SMS data through CDMA communication using a three axises acceleration sensor and a two axises gyro sensor. 5 healthy men were selected into a control group, and the fall recognition system using the three axises acceleration sensor and the two axises gyro sensor was devised to conduct an experiment. The system was attached to the upper of their sternum. According to the experiment protocol, the experiment was carried out 3 times repeatedly divided into 3 specific protocols: falling during gait, falling in stopped state, and falling in everyday life. Data obtained in the falling recognition system and LabVIEW 8.5 were used to decide if falling corresponds to that regulated in an analysis program applying an algorithm proposed in this study. In addition, results from falling recognition were transmitted to designated cellular phone in a SMS (Shot Message Service) form. These research results show that an erroneous detection rate of falling reached 19% in applying an acceleration signal only; 6% in applying an angular velocity; and 2% in applying a proposed algorithm. Such finding suggests that an erroneous detection rate of falling is improved when the proposed algorithm is applied incorporated with acceleration and angular velocity. In this study therefore, we proposed that a falling recognition system implemented in this study can make a contribution to the recognition of falling of the aged or the disabled.

• 대한기계학회논문집
• /
• 제11권6호
• /
• pp.913-922
• /
• 1987

본 연구에서는 Sn-15% Pb 재료에 대하여 실험에 의한 쌍 로울식 연속 주조의 주조특성을 구하고 로울러 열팽창과 열응력에 대한 유한요소해석을 통하여 제품 두께 와 로울러 변형과의 관계를 밝히고자 한다.