• Journal of Environmental Health Sciences
• /
• v.32 no.5 s.92
• /
• pp.499-505
• /
• 2006

Bioventing efficiency was compared in a continuous and an intermittent(6hr injection and 6hr rest) air injection mode. Two lab-scale columns which packed with 5 kg of soil artificially contaminated by diesel oil were operated. The columns were maintained at the $25^{\circ}C{\pm}2.5$ in order to minimize the effect of exterior temperature variation. The flow rate of air injection mode were maintained constantly at the flow rate of 10 ml/min. The moisture of the columns was stably maintained at $60{\sim}80%$ of field capacity. The nutrient compounds were added to make C:N:P ratio as 100:10:l. The continuous and intermittent injection modes showed 67.56% and 69.63% reduction of initial TPH concentration during 90 days, respectively. Two venting modes showed similar results in the analysis of the trends of the hydrocarbon utilizing bacterial counts for operating periods. The carbon dioxide production rate of the continuous injection mode was higher than that of intermittent injection mode. The loss of diesel oil by volatilization in the continuous and intermittent injection modes were about 5% and 1%, respectively. The lower volatilization loss in the intermittent injection mode suggested that the biodegradation of TPH in the intermittent injection mode was greater than that of the continuous mode. These results suggested that the intermittent injection mode is more efficient than the continuous venting mode.

• Journal of Environmental Health Sciences
• /
• v.32 no.5 s.92
• /
• pp.387-397
• /
• 2006

This study was performed to investigate the characteristics of indoor air quality(IAQ) in 91 public facilities from September 2004 to March 2005 in the Honam province(Chonnam, Gwangju). The measured air pollutants are $PM_{10}$, formaldehyde(HCHO), CO, $CO_{2}$ and total suspended bacteria(TSB), the maintenance standard materials of IAQ management law established by ministry of environment in Korea(MOE). We also surveyed establishment and operation of ventilation equipment. It was measured $1.2m{\sim}1.5m$ on the floor between 8 o'clock AM and 7 o'clock PM. As the result, $PM_{10}$ and CO was showed the highest concentration, $188.89{\mu}g/m^{3}$, 8.67 ppm, at the indoor parking. The concentration of HCHO was the highest in large store and steamer room. The concentration was respectively $118.70{\mu}g/m^{3}\;and\;113.21{\mu}g/m^{3}$. The concentration of $CO_{2}$ was the highest at the reading room of the library on the condition of natural ventilation. The concentration of $CO_{2}$ was 1,816 ppm and higher than the IAQ standards established by MOE. The TSB was just measured in the hospital and silver town. It was the highest at the admission room of hospital. The concentration of TSB was $766CFU/m^{3}$. The public facilities of this study were not exceed each maintenance standards except $CO_{2}$ but it was surveyed that the management will be needed about some air pollutant according to target facilities.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.134-134
• /
• 2012

We investigated the interface of poly (3-hexylthiophene) (P3HT) and C61-butyric acid methylester (PCBM) by using photoelectron spectroscopy (PES). These are the most widely used materials for bulk heterojunction (BHJ) organic solar cells due to their high efficiency. Study of the BHJ interfaces is difficult because the organic films are typically prepared by spin coating in ambient conditions. This is incompatible with the interface electronic structure probes such as PES, which requires ultrahigh vacuum conditions. Study of interface requires gradual deposition of thin films that is also incompatible with the spin coating process. In this work, we used electrospray vacuum deposition (EVD) technique to deposit P3HT and PCBM in high vacuum conditions. EVD allows us to form polymer thin films onto ITO substrate in a step-wise manner directly from solutions and to use PES without exposing the sample to the ambient condition. Although the morphology of the EVD deposited P3HT films observed by optical and atomic force microscopes is quite different from that of the spin coated ones, the valence region spectra were similar. PCBM was deposited on the P3HT film in a similar manner and the energy level alignment between these two materials was studied. We discuss the relation between Voc of P3HT:PCBM solar cell and HOMO-LUMO energy offset obtained in this study.

• Korean Journal of Materials Research
• /
• v.10 no.6
• /
• pp.445-449
• /
• 2000

Nickel ferrite $(Ni_{0.75}Fe_{2.25}O_4$ was synthesized by co-precipitation method in order to investigate its behavior under conditions of the reactor coolant system in pressurized light water nuclear power plants. Ammonia or potassium carbonate was used as a solution pH control agent, and aqueous ammonia or potassium carbonate solution or secondary distilled water was used as a co-precipitate washing agent. The effects of the pH control agent and the co-precipitate washing agent on the production yield on the basis of the Ni/Fe molar ratio and the particle characteristics of final products were investigated by XRD, SEM, EDX and XPS. The production yield was almost congruent with that of the initial aqueous mixture in case of using potassium carbonate as a pH control agent, while in case of using ammonia, it was quite changed. The difference seemed to be due to the effects of $Ni^{2+}{\leftarrow}NH_3$complexation in the aqueous solution and of the pH of co-precipitate washing agent.

• Applied Microscopy
• /
• v.46 no.1
• /
• pp.27-31
• /
• 2016

It has been investigated what kind of characteristic X-ray in electron probe micro-analyzer (EPMA) is effective for the determination of compounds of Si series materials. After comparing the characteristic X-rays among the primary and secondary lines in $K_{\alpha}$ and $K_{\beta}$ obtained from the Si series standard samples, it was found that the secondary line of $K_{\alpha}$ exhibited the most informative spectrum although the intensity was considerably weak. As a result of analyzing the spectrum shapes of the Si series standard samples, the spectrum shape of the secondary line of $K_{\alpha}$ for SiC was different from those for other Si compounds. To grasp the characteristics of the shape, a line was perpendicularly drawn from the peak top to base line in order to divide a spectrum into two areas. The area ratio of right to left was defined to call as the asymmetry index here. As a result, the asymmetry index value of the SiC was greater than one, while those of other Si compounds were less than one. It was found from the EPMA analysis that identification of SiC became successful to distinguish from other Si compounds and this method was applicable for micro-sized compounds in a practical composite material.

• Journal of Korea Foundry Society
• /
• v.31 no.5
• /
• pp.293-301
• /
• 2011

Representative magnesium alloys applied to the die-casting are AZ91, AM60, etc., and the application of these alloys is restricted to components operating at moderate temperatures, due to grain boundary siding of ${\beta}$-phase($Mg_{17}Al_{12}$) at temperatures above $120^{\circ}C$. Heat-resistant magnesium alloys such as AE42, AE44 have been developed, but that have been too burdensome to produce because of the expensive rare earth materials. Research work for the development of low-priced heat-resistant magnesium alloy is actively in progress and positive results are being reported. This study aims to investigate the effect of Ca additions on mechanical properties of Mg-4Al-2Sn heat resistant magnesium alloys. Mg-4Al-2Sn alloys with Ca (0wt.%, 0.3wt.%, 0.7wt.%, 1wt.%) have been produced through the die-casting process for the development of low-priced heat-resistant magnesium alloy, and high temperature tensile tests are performed using the specimens. The results showed that mechanical properties of Mg-4Al-2Sn-xCa increased with the addition of Ca up to 0.7wt.% Ca and further addition of Ca deteriorated the mechanical properties of the alloys. A significant amount of porosity was observed at the sample with 1wt%. Ca and the longer freezing range of the alloy was believed to cause the formation of porosity.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.32 no.2
• /
• pp.153-162
• /
• 2022

Objectives: Fused deposition modeling (FDM) 3D printer which is one of the material extrusion (MEX) technologies is an additive manufacturing (AM) process. 3D printers have been distributed widely in Korea, particularly in school and office, even at home. Several studies have shown that nanoparticles and volatile organic compounds (VOCs) were emitted from an FDM 3D printing process. The objective of this study was to identify types of chemicals possibly emitted from FDM 3D printing materials such as PLA (polylactic acid), ABS (acrylonitrile butadiene styrene), nylon, PETG (polyethylene terephthalate glycol), PVA (polyvinyl alcohol), PC (polycarbonate) filaments. Methods: 19 FDM 3D printing filaments which have been distributed in Korea were selected and analyzed VOCs emitted of 3D printing materials by headspace gas chromatography mass spectrometry (headspace GC-MS). Subsamples were put into a vial and heated up to 200℃ (500 rpm) during 20 minutes before analyzing FDM 3D printing filaments. Results: In the case of PLA filament, lactide and methyl methacrylate, the monomer components of one, were detected, and the volume ratio ranged 27~93%, 0.5~37% respectively. In the case of ABS filaments, styrene (50.5~59.1%), the monomer components of one, was detected. Several VOCs among acetaldehyde, toluene, ethylbenzene, xylene, etc were detected from each FDM 3D printing filaments. Conclusions: Several VOCs, semi-VOCs were emitted from FDM 3D printing filaments in this study and previous studies. Users were possibly exposed to ones so that we strongly believe that we recommend to install the ventilation system such as a local exhaust ventilation (LEV) when they operate the FDM 3D printers in a workplace.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.8.1-8.1
• /
• 2011

Nanocrystalline titanium dioxide ($TiO_2$) materials have been widely used as an electron collector in DSSC. This is required to have an extremely high porosity and surface area such that the dye can be sufficiently adsorbed and be electronically interconnected, resulting in the generation of a high photocurrent within cells. In particular, their geometrical structures and crystalline phase have been extensively investigated as important issues in improving its photovoltaic efficiency. In this study, we present a new strategy to fabricate a photoelectrode having a periodic structured $TiO_2$ film templated from 1D or 3D polystyrene (PS) microspheres array. Monodisperse PS spheres of various radiuses were used for colloidal array on FTO glasses and two types of photoelectrode structures with different $TiO_2$ materials were investigated respectively. One is the igloo-shaped electrode prepared by $TiO_2$ deposition by RF-sputtering onto 2D microsphere-templated substrates. At the interface between the film and substrate, there are voids formed by the decomposition of PS microspheres during the calcination step. These holes might be expected to play the predominant roles as scattering spherical voids to promote a light harvesting effect, a spacious structure for electrolytes with higher viscosity and effective paths for electron transfer. Additionally the nanocrystalline $TiO_2$ phase prepared by the RF-sputtering method was previously reported to improve the electron drift mobility within $TiO_2$ electrodes. This yields solar cells with a cell efficiency of 2.45% or more at AM 1.5 illumination, which is a very remarkable result, considering its $TiO_2$ electrode thickness (<2 ${\mu}m$). This study can be expanded to obtain higher cell efficiency by higher dye loading through the increase of surface area or multi-layered stacking. The other is the inverse opal photonic crystal electrode prepared by titania particles infusion within 3D colloidal arrays. To obtain the enlargement of ordered area and high quality of crystallinity, the synthesis of titania particles coated with a organic thin layer were applied instead of sol-gel process using the $TiO_2$ precursors. They were dispersed so well in most solvents without aggregates and infused successfully within colloidal array structures. This ordered mesoporous structure provides the large surface area leading to the enough adsorption of dye molecules and have an light harvesting effect due to the photonic band gap properties (back-and-forth reflection effects within structures). A major advantage of this colloidal array template method is that the pore size and its distribution within $TiO_2$ photoelectrodes are determined by those of latex beads, which can be controlled easily. These materials may have promising potentials for future applications of membrane, sensor and so on as well as solar cells.

• Journal of Society of Preventive Korean Medicine
• /
• v.16 no.3
• /
• pp.89-105
• /
• 2012

Objectives : This study was carried out to know the status of clinical utilization of Korean medical knowledge and the Korean medical knowledge system which Korean medical doctors want. Methods : Questionnaires were distributed to Korean medical doctors registered for the Association of Korean medicine via the email and 249 answered questionnaires were analyzed. Results : 50.6 % of Korean medical doctors utilized the textbooks for Korean medicine when they treated their patients. The reason why they did not utilize the textbooks for Korean medicine was mostly that 'it could not be applied directly into clinical application with only contents of textbook because clinical approach (diagnosis and treatment methods) was not clearly described in the textbook'. 48.6 % of Korean medical doctors utilized the EBM materials when they treated their patients. EBM materials that they referred included domestic articles, other EBM materials excluding papers and international academic papers based on PubMed in order. The reasons why they did not utilize the EBM materials were mostly that 'it was difficult to find the evidence' and 'EBM materials were not actually helpful for the clinical practice.' It was found that Korean medical doctors approached the disease in aspects of Korean and Western Medicine concurrently upon the diagnosis of patients and performed the diagnosis and treatment of Korean medicine on the diseases which seemed to be effective with Korean medicine. It was also found that they thought that they needed to know the Western medical knowledge as much as general doctors who have a doctor's license or family medicine specialists who comprehensively treat the general diseases know. Korean medical doctors wanted to have the systematic summary of modern research performance in fields of acupoint, acupuncture, herbal drugs and formula. They thought that constitutional medicine and Sa-am acupuncture therapy were representative characteristics in Korean medicine differentiated from Traditional Chinese medicine and Kampo medicine. Conclusions : Korean medical doctors wanted to establish the Korean medical knowledge system based on evidence focusing on clinical and practical contents. New Korean medical knowledge system should be established based on these requirements in the future.

• Korea Journal of Hospital Management
• /
• v.6 no.3
• /
• pp.69-89
• /
• 2001

This study is focused that the electronic commerce(EC) on the purchasing section may improve the efficiency and transparency of the hospitals management. After reviewing the purchasing activity of hospitals, I study the introduction, expected effects, and problems of EC. So, I am going to provide basic information for activating EC. The samples are managers of 170 hospitals, which are located on Seoul. As a result of collection this survey, I analyze 79 hospitals. For data analysis, I use $X^2$-test and ANOVA for purchasing management and the relevance of EC according to the level of care. The results of this study are 1. The problems on the management of purchasing section are: firstly, they don't have sufficient time to study market. Secondly, it is difficult to find competitive suppliers. And, lastly, they cannot gather a lot of information about the price of products. 2. There are many answers of the needs on the introduction of B2B. However, some hospitals think they don't need it. But, the most answers are that the EC will be settled within 4 years. So, we can realize that these hospitals are getting interested on the EC. On the other hand, I find that they prefer outside EC companies for the introduction of EC. 3. On the expected effects on EC, first is the effectiveness of the market survey. The next is to collect information of adequate price of products owing to clear transaction, find easier new suppliers and gather useful data. 4. On the external problems of the introduction of EC, there is low credibility related to the security and the weakness of suppliers' information system. Especially, on the Real Transaction Price Payment system, the bigger bed size, the higher understanding on these problems. On the internal problems of the introduction of EC, first is the burden of the introduction of EC and operating cost. Especially, on the burden of the disclosure of revenue source, the smaller bed size, the higher understanding on this problem So, this is a point which deserves my attention statistically. However, this shows relatively little understanding about incomplete the standard of product category and the weak information system of hospital. Through this study, I am going to suggest 3 points for the activation of the introduction of EC on hospitals. 1. The reform of the Real Transaction Price Payment System on medical supplies and materials for medical treatment 2. The establishment of the standard of product category 3. The promotion of information system based on network.