• Journal of the Korea Institute of Building Construction
• /
• v.15 no.1
• /
• pp.1-7
• /
• 2015

The objective of this study is to develop a high-performance foamed concrete made with a new mixture proportioning as an alternative of autoclaved lightweight concrete (ALC) block. For the early-strength gain of the foamed concrete under an atmospheric curing condition, the binders and chemical agents were specially contrived as follows: 3% anhydrous gypsum was added to ordinary portland cement (OPC) in which $3CaO{\cdot}SiO_2$ content was controlled to be above 60%; and the content of polyethylene glycol alkylether in a polycarboxylate-based water-reducing agent was modified to be 28%. Using these binders and chemical agents, 11 mixes were prepared with the parameters of W/B ratio (30% to 20% in a interval of 2.5%) and unit binder content ($400kg/m^3$ to $650kg/m^3$ in a interval of $50kg/m^3$). The quality and availability of the mixed foamed concrete were examined according to the minimum requirements specified in the KS for ALC block and existed conventional foamed concrete. The measured properties satisfied the minimum requirement of KS for ALC block and proved that the developed high-performance foamed concrete had considerable potential for practical application.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.05a
• /
• pp.12-13
• /
• 2019

The bearing capacity of the wall against the eccentric load when the washbasin was attached on the ALC block wall was tested. Test methods are BS EN 14688 and BS 5234-2. Tests in accordance with BS EN 14688 showed that the holding capacity of steel was much stronger and more stable when HA-II (chemical anchor) was used than when the washbasin was fixed using HA-I (plastic anchor). As an experimental result according to the Annex K of BS 5234-2, the bearing capacity of ALC block wall corresponded to the "stage in which the force works(performance grade) 1,500N" for all of the cases where a washbasin is fixed using two types of the wall's dedicated anchors(HA-I and HA-II).

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.05a
• /
• pp.10-11
• /
• 2019

Interior stone walls are using commonly in non-bearing lightweight walls of apartments. The stones of interior wall were two types, one is a granite stone, another is a marble stone. Granite stone is attached by the epoxy adhesive and marble stone is attached by dedicated anchor and fastener. The impact resistance test was carried out interior stone walls in accordance with KS F 2613. The test methods included the impact resistance tests by each of soft impact body and hard impact body. The results of the test have proved that interior stone walls can withstand the soft impact bodies and hard impact bodies that are likely to happen in everyday life.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.367-368
• /
• 2009

High-rise building in modern society is becoming increasingly necessary to reduce the weight of the building. Accordingly, increased use of lightweight bubble concrete is a trend Porous ceramics (ALC) is the most common, lightweight bubble concrete. And it is by lightweight blocks the same used as building materials. This research is related to the physical characteristics of ALC controlled by particle size and contents of raw materials.

• Magazine of RCR
• /
• v.14 no.4
• /
• pp.26-31
• /
• 2019

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.41 no.5
• /
• pp.1-8
• /
• 2004

In this paper, we propose a machine vision system by which we can measure the size of ALC blocks in real-time in the Production Process. The images obtained by our system were processed by a devised algorithm, specially designed for the enhanced measurement accuracy. from the experimental results, we could find that the required measurement accuracy specification is sufficiently satisfied by using our proposed method.

• Journal of Institute of Control, Robotics and Systems
• /
• v.9 no.6
• /
• pp.448-455
• /
• 2003

A system design technique of automatic thickness measurement and defect inspection system, which measures the thickness of the ALC(Autoclaved Lightweight Concrete) block and inspects the defect on a realtime basis is proposed. The image processing system was established with a CCD camera, an image grabber, and a personal computer without using assembled measurement equipment. The image obtained by this system was analyzed by a devised algorithm, specially designed for the enhanced measurement accuracy. For the realization of the proposed algorithm, the preprocessing method that can be applied to overcome uneven lighting environment, an enhanced edge decision method using 8 edge-pairs with irregular and rough surface, the unit length decision method in uneven condition with rocking objects, and the curvature calibration method of camera using a constructed grid are developed. The experimental results, show that the required measurement accuracy specification is sufficiently satisfied using our proposed method.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.6
• /
• pp.494-500
• /
• 2004

This paper presents a machine vision system, which inspects the measurement of the ALC block on a real-time basis in the production process. The automatic measurement system was established with a CCD camera, an image grabber, and a personal computer without using assembled measurement equipment. Images obtained by this system was processed by an algorithm, specially designed for an enhanced measurement accuracy. For the realization of the proposed algorithm, a preprocessing method that can be applied to overcome uneven lighting environment, boundary decision method, unit length decision method in uneven condition with rocking objects, and a projection of region using pixel summation are developed. From our experimental results, we could find that the required measurement accuracy specification is sufficiently satisfied by using the proposed method.

• Proceedings of the KIEE Conference
• /
• 2002.11c
• /
• pp.342-348
• /
• 2002

This paper presents a computer image processing system, which measures the thickness of the ALC block and inspects the defect on a real-time basis. The Image processing system was established with a CCD camera, an image grabber, and a personal computer without using assembled measurement equipment. The image obtained by the system was analyzed by a devised algorithm, specially designed for the enhanced measurement accuracy. For the realization of proposed algorithm, the pre-processing method that can be applied to overcome uneven lighting environment, and threshold decision method, and subpixel method are developed. from the experimental results, we could find that the required measurement accuracy specification is sufficiently satisfied using our proposed method.

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.661-664
• /
• 2003

This paper presents a computer image processing system, which inspects the measurement of the ALC block on a real-time basis. The Image processing system was established with a CCD camera, an image grabber, and a personal computer without using assembled measurement equipment. The image obtained by the system was analyzed by a devised algorithm, specially designed for the enhanced measurement accuracy. From the experimental results, we could find that the required measurement accuracy specification is sufficiently satisfied using our proposed method.