• Composites Research
• /
• v.16 no.4
• /
• pp.44-50
• /
• 2003

The damage zone around a crack tip occurring before the fracture is a significant domain. which affects the toughening mechanism of materials. In this study. the growth process of damage zone in the vicinity of crack tip for rubber-modified epoxy resin is investigated using an acoustic emission(AE) analysis. The weight fractions of rubber(CTBN 1300$\times$B) in rubber-modified epoxy resin are 5 wt% and 15 wt%. The fracture toughness($K_{IC}$) and the fracture energy($G_{IC}$) were measured using 3 point bending single-edge notched specimens. The damage zone and rubber particles distributed around the crack tip were observed by a polarized optical microscope and an atomic force microscope(AFM). The damage zone around crack tip of rubber-modified epoxy resin was formed at 13 % loading and developed until 57 % loading of the fracture load. The crack initiated at 57 % loading grew repeatedly in the stick-slip propagation behavior. Based on time-frequency analysis, it was confirmed that AE signals with frequency bands of 0.15~0.20 MHz and 0.20~0.30 MHz were generated from cavitation and stable/unstable cracking inside the damage zone.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.4
• /
• pp.75-80
• /
• 2013

Single crystal sapphire being used in high technology industry is a brittle material with a high hardness and excellent physical properties. ELID(Electrolytic In-Process Dressing) grinding technology was applied to material removal machining process of single crystal sapphire wafer. Ultrasonic vibration which added to material using ultrasonic table was adopted to efficient ELID grinding of sapphire materials. The evaluation of the ground surface of single crystal sapphire wafer was carried out by means of surface measuring by using AFM(Atomic Force Microscope), surface roughness tester and optical microscope device. As the results of experiment, it was shown that more efficient grinding was conducted when using ultrasonic table. In case of using #170 grinding wheel, surface roughness of ELID ground specimen in using ultrasonic table was superior to ELID ground specimen without ultrasonic table. However, In case of using #2000 grinding wheel, surface roughness of ELID ground specimen in using ultrasonic table was inferior to ELID ground specimen without ultrasonic table.

• Membrane and Water Treatment
• /
• v.9 no.1
• /
• pp.43-51
• /
• 2018

Hollow fiber (HF) membranes are gaining wide interest over flat membranes due to their compaction and high area to surface volume ratio. This work addresses the fabrication of HF from polysulfone (PS) and polyethersulfone (PES) using N-methylpyrrolidone (NMP) as solvent in addition to other additives to achieve desired characteristics. The semi-pilot spinning system includes jacketed vessel, four spinneret block, coagulation and washing baths in addition to dryer and winder. Different parameters affecting dry-wet spinning phase inversion process were investigated. Dope compositions of PES, NMP and polyvinyl pyrrolidone (PVP) of varying molecular weights as additive were addressed. Some critical parameters of importance were also investigated. Those include dope flow rate, air gap, coagulation & washing baths and drying temperatures. The measured dope viscosity was in the range from 1.7 to 36.5 Pa.s. Air gap distance was adjusted from 20 to 45 cm and coagulation bath temperature from 20 to $46^{\circ}C$. The HF membranes were characterized by scanning electron microscope (SEM), atomic force microscope (AFM) and mechanical properties. Results indicated prevalence of finger like structure and average surface roughness from about 29 to 78.3 nm. Profile of stress strain characteristics revealed suitability of the fibers for downstream interventions for fabrication of thin film composite membrane. Different empirical correlations were formulated which enable deeper understanding of the interaction of the above mentioned variables. Data of pure water permeability (PWP) confirmed that the fabricated samples fall within the microfiltration (MF)-ultrafiltration (UF) range of membrane separation.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.32.2-32.2
• /
• 2011

반도체 생산공정에서 CMP (Chemical-mechanical planarization) 공정은 우수한 전기전도성 재료인 Cu의 사용과 다층구조의 소자를 형성하기 위해서 도입되었으며, 최근 소자의 집적도가 증가함에 따라 CMP 공정 비중은 점점 높아지고 있다. Cu CMP 공정에서 연마제인 슬러리는 금속 표면과의 물리적 화학적 반응을 동시에 사용하여 표면을 연마하게 되며, 연마특성을 향상시키기 위해 산화제, 부식방지제, 분산제 및 다양한 계면활성제가 첨가된다. 하지만 슬러리는 Cu 표면을 평탄화하는 동시에 오염입자, 유기오염물, 스크레치, 표면부식 등을 발생시키며 결과적으로 소자의 결함을 야기시킨다. 특히 부식방지제로 사용되는 BTA (Benzotriazole)은 Cu CMP 공정 중 Cu-BTA 형태로 표면에 흡착되어 오염원으로 작용하며 입자오염을 증가시시고 건조공정에서 물반점 등의 표면 결함을 발생시킨다. 이러한 문제점을 해결하기 위해 Cu 표면에서 식각과 부식반응을 최소화하며, 오염입자 제거 및 유기오염물을 효과적으로 제거하기 위한 Post-CMP 세정 공정과 세정액 개발이 요구된다. 본 연구에서는 오염입자 및 유기물 제거와 동시에 표면 거칠기와 부식현상을 제어할 수 있는 post Cu CMP 세정액을 개발 평가하였다. 오염입자 및 유기오염물을 제거하기 위해서 염기성 용액인 TMAH 사용하였으며, Cu 이온을 용해할 수 있는 Chelating agent와 표면 부식을 억제하는 부식 방지제를 사용하여 세정액을 합성하였다. 접촉각 측정과 FESEM(field Emission Scanning Electron Microscope) 분석을 통하여 CMP 공정에서 발생하는 유기오염물과 오염입자의 흡착과 제거를 확인하였으며 Cu 웨이퍼 세정 전후의 표면 거칠기의 변화와 식각량을 AFM(Atomic Force Microscope)과 4-point probe를 사용하여 각각 평가하였다. 또한 세정액 내에서의 연마입자의 zeta-potential을 측정 및 조절하여 세정력을 향상시켰다. 개발된 세정액과 Cu 표면에서의 화학반응 및 부식방지력은 potentiostat를 이용한 전기화학 분석법을 통해서 chelating agent와 부식방지제의 농도를 최적화 시켰다. 개발된 세정액을 적용함으로써 Cu-BTA 형태의 유기오염물과 오염입자들이 효과적으로 제거됨을 확인하였다.

• Korean Journal of Materials Research
• /
• v.30 no.4
• /
• pp.169-175
• /
• 2020

Silicon nitride thin films are deposited by RF (13.57 MHz) magnetron sputtering process using a Si (99.999 %) target and with different ratios of Ar/N₂ sputtering gas mixture. Corning G type glass is used as substrate. The vacuum atmosphere, RF source power, deposit time and temperature of substrate of the sputtering process are maintained consistently at 2 ~ 3 × 10^-3 torr, 30 sccm, 100 watt, 20 min. and room temperature, respectively. Cross sectional views and surface morphology of the deposited thin films are observed by field emission scanning electron microscope, atomic force microscope and X-ray photoelectron spectroscopy. The hardness values are determined by nano-indentation measurement. The thickness of the deposited films is approximately within the range of 88 nm ~ 200 nm. As the amount of N₂ gas in the Ar:N₂ gas mixture increases, the thickness of the films decreases. AFM observation reveals that film deposited at high Ar:N₂ gas ratio and large amount of N₂ gas has a very irregular surface morphology, even though it has a low RMS value. The hardness value of the deposited films made with ratio of Ar:N₂=9:1 display the highest value. The XPS spectrum indicates that the deposited film is assigned to non-stoichiometric silicon nitride and the transmittance of the glass with deposited SiO₂-Si_xN_y thin film is satisfactory at 97 %.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.424-424
• /
• 2008

Dye-sensitized Solar Cell (DSC) is a new type of solar cell by using photocatalytic properties of $TiO_2$. The electric potential distribution in DSCs has played a major role in the operation of such cells. Models based on a built-in electric field which sets the upper limit for the open circuit voltage(Voc) and/or the possibility of a Schottky barrier at the interface between the mesoporous wide band gap semiconductor and the transparent conducting substrate have been presented. $TiO_2$ thin films were deposited on the FTO substrate by Nd:YAG Pulsed Laser Deposition(PLD) at room temperature and post-deposition annealing at $500^{\circ}C$ in flowing $O_2$ atmosphere for 1 hour. The structural properties of $TiO_2$ thin films have investigated by X-ray diffraction(XRD) and atomic force microscope(AFM). Thickness of $TiO_2$ thin films were controlled deference deposition time and measurement by scanning electron microscope(SEM). Then we manufactured a DSC unit cells and I-V and efficiency were tested using solar simulator.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.382.2-382.2
• /
• 2014

We explain a method to fabricate multi-layered transparent conductive films (TCF) using graphene oxide (GO), copper powder and polyurethane (PU) solution. The flexible graphene nanosheets (GNSs) serve as nanoscale connection between conductive copper nanoparticles (CuNps) and PU nanofibers, resulting in a highly flexible TCF. To fabricate conductive films with high transmittance, polyurethane (PU) nanofibers were used for a conductive network consisting of CuNps and GNSs (CuNps-GNSs). In this experiment, copper powder and graphene oxides were mixed in deionized water with the ultrasonication for 2 h. NaBH4 solution is used as a reduction agents of CuNps and GNSs (CuNps-GNSs) under a nitrogen atmosphere in the oil bath at 100% for 24 h to mixed. The purified and dispersed CuNp-GNS were obtained in deionized water, and diluted to a 10wt.% based on the contents of GNSs. Polyurethane (PU) nanofibers on a PET substrate were formed by electrospinning method. PET slides coated with the PU nanofibers were immersed into CuNp-GNS solution for several second, rinsed briefly in deionized water, and dried to obtain self-assembled CuNp-GNS/PU films. The morphology of the multi-layered films were characterized with a field emission scanning electron microscope (FE-SEM, Hitachi S-4700) and atomic force microscope (AFM, PSIA XE-100). The electrical property was analysed by the I-V measurement system and the optical property was measured by the UV/VIS spectroscopy.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.59-59
• /
• 2010

ZnO는 II-VI 족 화합물 반도체로써 상온에서 큰 엑시톤 결합에너지 (~60 meV) 를 가지며 밴드갭이 3.37 eV인 직접 천이형 반도체로 잘 알려진 물질이다. 이러한 ZnO의 물리적 특성은 광학소자로 상용화된 GaN와 유사하기 때문에 LED나 LD등의 광 소자 재료로 주목 받고 있다. 또한 ZnO는 3족 원소 (In, Ga, Al)를 도핑 함으로써 전기적 특성 제어가 가능한 장점을 가지고 있다. 본 연구는 펄스레이저 증착법 (Pulsed Laser Deposition)을 이용하여 Si (111) 기판 위에 ZnO:In 박막을 성장 시켰으며, 도핑된 indium 양에 따른 ZnO 박막의 배향성 변화를 관찰 하였다. X-선 회절 분석법 (X-ray diffraction), 탐침형 원자현미경 (Atomic Force Microscope) 그리고 투과전자 현미경 (Transmission Electron Microscope)을 측정하였다. XRD 측정 결과 un-doped ZnO 박막은 (002) 방향으로 c-축 우선성장 하였다. 그러나 ZnO 박막내의 Indium 양이 증가 할수록 (002) 방향에서 (101), (102), (103) 등의 (101) 방향으로 성장이 변화 하였으며 5 at.% 이상에서는 (100) 방향의 성장이 관찰 되었다. TEM 측정 결과 un-doped ZnO 박막은 columnar 구조로 성장 되었으나, Indium 양이 증가할수록 column의 size가 감소하며, 5 at.% 이상에서 columnar 구조 성장이 거의 관찰되지 않는다. AFM 결과에서는 Indium 양이 증가 할수록 박막의 표면거칠기와 결정립 크기가 감소하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.169-169
• /
• 2012

현재 디스플레이 시장은 LCD (Liquid Crystal Display), PDP (Plasma Display Panel) 등과 같이 평판 디스플레이가 주류를 이루고 있으며 현재에는 기존의 디스플레이와는 달리 잘 휘어지고 높은 투과성을 가지는 플렉시블 디스플레이에 대한 연구가 활발히 진행 중이다. 하지만 이러한 플렉시블 디스플레이에 사용되는 플라스틱 기판의 경우 용제에 대한 화학적 저항성 및 기계적인 안정성이 취약한 점과 대기중의 수분이나 산소가 플라스틱 기판을 통하여 소자내로 침투하게 되어 금속전극을 산화시키거나 기포 또는 흑점 등과 같은 비 발광 영역이 확산되어 소자의 수명을 단축시키는 치명적인 단점을 가진다. 이에 본 실험에서는 고밀도 플라즈마 형성이 가능하고 저온공정이 가능한 FTS (Facing Target Sputtering) 장비를 이용하여 Polyethylene terephthalate (PET) 기판위에 낮은 수분 투과율 또는 산소 투과율을 갖는 양질의 무기 산화막을 적층하기 위해 저 투습도 및 기계적인 경도 향상을 위한 비 반응성 박막으로 $Al_20_3$층을 Ar분위기에서 증착하였고 그 위에 박막의 stress 감소, 유연성 향상을 위한 반응성 박막으로 Al을 Ar과 $O_2$를 비율별로 증착하여 비교 실험하였다. 이와 같이 제작된 무기산화막들을 Uv- spectrophotometer를 이용하여 광학적 특성을 조사한 결과 가시광 영역에서 모두 80% 이상의 높은 투과율을 나타내었으며, 그 외 XRD (X-ray Diffraction)를 사용하여 결정성을 확인, SEM (Scanning Electron Microscope), AFM (Atomic Force Microscope)을 이용하여 박막의 구조와 표면향상 및 표면조도를 측정한 결과 모든 박막에서 밀집도가 좋으며 거칠기가 작은 것으로 확인되었다. 마지막으로 수분 투과율(WVTR)을 알아보기 위해 Mocon (Permatran W3/31)장비를 이용하여 측정한 결과 $1.0{\sim}3.0{\times}10^{-3}g/m{\cdot}day$의 낮은 수분 투과율을 볼 수 있었다. 이러한 측정 결과로 볼 때 향후 FTS 장비를 이용하여 양질의 플라즈마를 형성하여 알루미늄 무기산화막을 이용한 고밀도 다층막을 형성하면 더욱 낮은 수분투과율을 갖는 가스차단막을 제작할 수 있을 것으로 보여지며 반도체 소자 및 디바이스의 Pachaging으로도 사용가능 할 것이라 사료된다. 본 연구는 한국산업기술진흥원에서 지원하는 2011년도 지역산업기술개발사업의 연구수행으로 인한 결과물임을 밝힙니다.

• Laser Solutions
• /
• v.17 no.1
• /
• pp.1-6
• /
• 2014

Indium tin oxide (ITO) is an important transparent conducting oxide (TCO). ITO films have been widely used as transparent electrodes in optoelectronic devices such as organic light-emitting devices (OLED) because of their high electrical conductivity and high transmission in the visible wavelength. Finding ways to control ITO micromachining depth is important role in the fabrication and assembly of display field. This study presented the depth control of ITO patterns on glass substrate using a femtosecond laser and slit. In the proposed approach, a gaussian beam was transformed into a quasi-flat top beam by slit. In addition, pattern of square type shaped by slit were fabricated on the surfaces of ITO films using femtosecond laser pulse irradiation, under 1030nm, single pulse. Using femtosecond laser and slit, we selectively controlled forming depth and removed the ITO thin films with thickness 145nm on glass substrates. In particular, we studied the effect of pulse number on the ablation of ITO. Clean removal of the ITO layer was observed when the 6 pulse number at $2.8TW/cm^2$. Furthermore, the morphologies and fabricated depth were characterized using a optical microscope, atomic force microscope (AFM), and energy dispersive X-ray spectroscopy (EDS).