• Journal of Electrical Engineering and Technology
• /
• 제3권2호
• /
• pp.243-253
• /
• 2008

This paper deals with the analysis, design, and implementation of a single phase AC-DC Zeta converter with high frequency transformer isolation and power factor correction(PFC) in two modes of operation, discontinuous current mode of operation(DCM), and continuous current mode of operation(CCM). A Digital Signal Processor(DSP) based implementation is carried out for validation of the Zeta converter developed design in discontinuous mode of operation. A comparison of both modes of operation is presented for a 1kW power rating from the point of view of steady state and dynamic behavior, power quality, simplicity, control technique, device rating, and converter size. The experimental results of a developed prototype of Zeta converter are presented for validation of the developed design. It is observed that CCM is most suitable for higher power applications where it requires some complex control and sensing of the additional variables.

• 전기전자학회논문지
• /
• 제16권4호
• /
• pp.335-342
• /
• 2012

본 논문에서는 고효율과 고역률을 위한 새로운 DCM-ZVS 스텝 업-다운 AC-DC 컨버터에 대해 연구된다. 제안한 DCM-ZVS 컨버터에 사용된 스위칭 소자들은 새로운 유사공진 회로에 의해 소프트 스위칭 기법으로 동작되고, 펄스폭변조(PWM) 방식에 의한 전류불연속모드(DCM)로 구동된다. 제안한 컨버터의 유사공진 회로는 스텝 업-다운 인덕터와 무손실 스너버 커패시터로 구성되고, 또한 DCM에 의해 제어회로 기법과 제어회로 구성이 간단한 장점이 주어진다. 입력 교류 전류파형은 일정 스위칭 주파수에 의한 교류 입력전압의 크기에 비례한 유사 정현파형으로 된다. 그 결과, 제안한 DCM-ZVS 컨버터는 낮은 스위칭 손실과 고효율을 얻을 수 있으며, 컨버터의 입력역률은 거의 단위역률로 된다. 해석적 결과의 타당성은 다양한 컴퓨터 시뮬레이션과 실험 결과를 통해 입증된다.

• Journal of Power Electronics
• /
• 제7권1호
• /
• pp.44-54
• /
• 2007

Ac-dc power conversion can either be done with two separate converter stages or with a single converter stage. Two-stage ac-dc converters, however, can be costly and complex, while the performance of single-stage converters is compromised due to a reduced number of components. Several researchers have therefore proposed adding some sort of auxiliary circuit consisting of a second switch and some passive elements to single-stage converters to improve their performance. Although these modified single-stage converters may have two converters, they are not two-stage converters as they do not have two separate and independently controlled converters that are always operating to convert power from one form to another. In this paper, the operation of ac-dc single-stage converters is first reviewed and their strengths and weaknesses are noted. The operation of several modified single-stage converters, including one proposed by the authors, is then discussed, and the paper concludes by presenting experimental results that confirm the feasibility of the proposed converter.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2012년도 추계학술대회 논문집
• /
• pp.103-104
• /
• 2012

In the AC module system, mismatch problem between AC power and constant input power is occurred. To solve this problem, electrolytic capacitor is utilized for diminishing power pulsation in PV side. However, it has disadvantages of low life span and weak in temperature. Decoupling method has been studied to reduce the capacitance and replaces electrolytic capacitor to film capacitor. This paper proposes design method for decoupling circuit which bidirectional DC-DC converter using soft switching. Proposed system is verified by design optimization and simulation results.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2008년도 하계학술대회 논문집
• /
• pp.34-36
• /
• 2008

This paper is given a full detail of mathematical analyses of input current for novel active type power factor correction(PFC) AC-DC converter of step up-down added electric isolation. These are compared with harmonics components of input current for a conventional PFC converter of electric isolation type. The proposed PFC converter is constructed in using a new loss-less snubber circuit to achieve a soft switching of control device. Also the proposed converter for discontinuous conduction mode(DCM) eliminates the complicated circuit control requirement and reduces the size of components. The input current waveform in the proposed converter is got to be a sinusoidal form of discontinuous pulse in proportion to magnitude of ac input voltage under the constant duty cycle switching. Therefore, input power factor is nearly unity and the control method is simple. Particularly, the stored energy of loss-less snubber capacitor is recovered with input side and increases input current from resonant operation. The result is that input power factor of the proposed converter is higher than that of a conventional PFC converter. Some simulative results on computer and experimental results are included to confirm the validity of the analytical results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.582-584
• /
• 1996

A new single stage AC/DC converter with a high power factor is proposed. The proposed converter gives good power factor correction, low current harmonic distortions, and tight output regulations. This converter also has an high efficiency by employing Active-clamp method and synchronous rectifiers. To verify performances of the proposed converter, 90W-converter is designed. This prototype meets the IEC555-2 requirements satisfactorily with nearly unity power factor.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 춘계전력전자학술대회 논문집(1)
• /
• pp.352-357
• /
• 2003

A new single stage power factor correction(PFC) AC/DC converter based on zero voltage switching(ZVS) full bridge topology is proposed. Since the series-connected two transformers act as both output inductor and main transformer by turns, the proposed converter has a wide ZVS range without additional devices for ZVS. Furthermore, since there is no need to use an output inductor, the proposed converter features high power density. The proposed converter gives the good power factor correction and low line current harmonics distortion. A mode analysis and experiment results are presented to verify the validity of the proposed converter.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2009년도 추계학술대회 논문집
• /
• pp.407-410
• /
• 2009

A piezoelectric device which converts mechanical vibration energy into electrical energy is able to harvest energy and the usable energy is mW ${\sim}$ W, hence a converter is necessary to acquire the energy efficiently. Various limited conditions should be considered for the design of AC/DC converter for energy harvesting of a piezoelectric device supplying small amount of energy. In addition to simple structure, compact size, light weight and high efficiency, the energy harvesting AC!DC converter should adopt the technique of self operating, in which only the harvested energy from the piezoelectric device is available. This paper proposes new AC/DC resonant boost converter to harvest efficiently electrical energy from mechanical vibration energy, analyzes the operating characteristics of the converter and proves its feasibility for energy harvester with PSPICE simulation and experiment.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2005년도 춘계학술대회논문집
• /
• pp.8-13
• /
• 2005

In this paper discusses single-phase DC-AC Inverter design of reversible power converter that driven by binary combination at different transformer winding ratio by BCD code level. It has a advantage that constructs a control system simply and obtain load current of good quality without filter circuit and free from noise or isolation for lower switching frequency. In this research, study on current type converter and inverter circuit that consist for possibility of AC-DC/DC-AC multi-level reversible converter.

• Journal of Power Electronics
• /
• 제8권1호
• /
• pp.60-73
• /
• 2008

In this paper a three-phase ac-to-dc resonant converter with high input power factor and isolated output is proposed. To improve the input power factor of the converter, high frequency current is injected into the input of the three-phase diode bridge rectifier. It is injected through an impedance network consisting of a series of L-C branches from the output of the high frequency three-phase inverter. A narrow switching frequency variation is required to regulate the output voltage. A design example with different design curves is illustrated along with the component ratings. Experimental verification of the converter is performed on a prototype of 3 kW, 1000 V output, operating above 300 kHz. Experimental results confirm the concept of the proposed converter. Narrow switching frequency variation is required to regulate the output voltage.