• 한국표면공학회지
• /
• 제51권6호
• /
• pp.421-429
• /
• 2018

In this study, various electrochemical experiments were carried out to compare the corrosion characteristics of AA5052-O, AA5083-H321 and AA6061-T6 in seawater. The electrochemical impedance and potentiostatic polarization measurements showed that the corrosion resistance is decreased in the order of AA5052-O, AA5083-H321 and AA6061-T6, with AA5052-O being the highest resistant. This is closely associated with the property of passive film formed on three tested Al alloys. Based on the slope of Mott-Schottky plots of an n-type semiconductor, the density of oxygen vacancies in the passive film formed on the alloys was determined. This revealed that the defect density is increased in the order of AA5052-O, AA5083-H321 and AA6061-T6. Considering these facts, it is implied that the addition of Mg, Si, and Cu to the Al alloys can degrade the passivity, which is characterized by a passive film structure containing more defect sites, contributing to the decrease in corrosion resistance in seawater.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2011년도 춘계학술대회 논문집
• /
• pp.1235-1236
• /
• 2011

• 한국자동차공학회논문집
• /
• 제20권3호
• /
• pp.77-82
• /
• 2012

It is well known that the targeted fuel efficiency could only be achieved by more than 40% reduction of the vehicle weight through improved design and extensive utilization of lightweight materials. In order to obtain the goal of the weight reduction of automobiles, the researches about lighter and stronger rear sub-frame have been studied without sacrificing the safety of rear sub-frame. In this study, the weight reduction design process of rear sub-frame could be proposed based on the variation of von-Mises stress contour by substituting an AA6061 (aluminum 6061 alloy) having tensile strength of 310 MPa grade instead of SAPH440 steels. In addition, the stress ratio variations (stress over fatigue limit) of the rear sub-frame were examined and compared carefully. It could be reached that this approach method could be well established and be contributed for light-weight design guide and the optimum design conditions of the automotive rear sub-frame development.

• 소성∙가공
• /
• 제26권2호
• /
• pp.101-107
• /
• 2017

Aluminum alloys are widely used in automotive industry because of their high strength-to-density ratio and excellent corrosion resistance. However, conventional cold stamping of aluminum alloys leads to low formability and excessive spring-back. To overcome these problems, Hot Forming Quenching (HFQ) is applied to manufacture automotive part using aluminum alloy. The purpose of this study is to investigate effect of forming temperature on spring-back in HFQ of T6 heat treated AA6061 sheet. In this study, hat shape forming test was adopted to evaluate spring-back characteristics according to various forming temperatures. In additions, the test was also performed with warm forming conditions in comparison with dimensional accuracy of HFQed part. The experimental results showed that dimensional accuracy of HFQed part was superior to warm formed part and amount of spring-back was decreased as forming temperature rise.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 추계학술대회논문집
• /
• pp.11-16
• /
• 1997

In this study, the finite element analysis of AA6061 wheel forging processes over hot working range is performed and a thermo-viscoplasticity theory applicable to hot forging is applied for simulation. Aluminum alloy has frequently been utilized to manufacture automobile and aircraft parts due to its various advantages such as lightness, good forgeability, and wear resistance. Several forging conditions are applied to the simulation, such as die speeds, rib thicknesses, and depth of die cavity. The effectiveness of the simulation results is summarized in terms of metal flow, strain distributions, temperature distributions, forging load, which are essential to over all process design.

• Steel and Composite Structures
• /
• 제28권6호
• /
• pp.759-766
• /
• 2018

Friction Stir Welding (FSW) is a solid-state process, where the objects are joined together without reaching their melting point. It has been shown that this method is a suitable way to join dissimilar aluminium alloys. The current article employed hole drilling technique to measure the residual stress distribution experimentally in different zones of dissimilar aluminium alloys AA6061-T6 and AA7075-T6 Butt welded using FSW. Results are compared with those of similar AA6061-T6 plates joined using a conventional fusion welding method called tungsten inert gas (TIG). Also, the evolution of the residual stresses in the thickness direction was investigated, and it was found that the maximum residual stresses are below the yield strength of the material in the shoulder region. It was also revealed that the longitudinal residual stresses in the joint were much larger than the transverse residual stresses. Meanwhile, Vickers micro hardness measurements were performed in the cross-section of the samples. The largest hardness values were observed in the stir zone (SZ) adjacent to the advancing side whereas low hardness values were measured at the HAZ of both alloys and the SZ adjacent to the retreating side.

• 한국자동차공학회논문집
• /
• 제18권5호
• /
• pp.45-49
• /
• 2010

The automotive industry has shown a growing interest in tube hydroforming during the past years. The advantages of hydroforming (less thinning, a more efficient manufacturing process, etc.) can, for instance, be combined with the high strength of extra high strength steels, which are usually less formable, to produce structural automotive components which exhibit lower weight and improved service performance. Design and production of tubular components require knowledge about tube material and forming behavior during hydroforming and how the hydroforming operation itself should be controlled. These issues are studied analytically in the present paper. In this study, the whole process of rear sub-frame parts development by tube hydroforming using AA6061 material is presented. At the part design stage, it requires feasibility study and process design aided by CAE (Computer Aided Engineering) to confirm hydroformability in details. Effects of parameters such as internal pressure, axial feeding and geometry shape in automotive rear sub-frame by hydroforming process were carefully investigated. Overall possibility of hydroformable rear sub-frame parts could be examined by cross sectional analyses. Moreover, it is essential to ensure the formability of tube material on every forming step such as pre-bending and hydroforming. In addition, all the components of prototyping tool are designed and interference with press is examined from the point of geometry and thinning.

• 소성∙가공
• /
• 제30권4호
• /
• pp.195-200
• /
• 2021

In this study, we investigated the dominant processing variables that would influence the microstructural development of AA6061 deformed by differential speed rolling (DSR) at ambient temperature. For this purpose, we carried out a series of DSR on the samples to investigate the effects of roll speed ratio, sample rotation, and number of operation under specific rotation. Among these, the condition with a height reduction of 75% at a speed ratio of 1:4 through rotation along rolling direction (RR) displayed the pronounced results of more homogenous matrix-structure and superior mechanical properties than the others tested in this study. This was mainly due to the cross shearing of macro-shear pattern in segment where dynamic recrystallization took place with ease throughout the sample. Thus, an average microhardness value of 101 Hv was obtained in the present sample deformed by 4-pass DSR with RR where macro cross-shearing was effectively applied.

• 한국재료학회지
• /
• 제32권2호
• /
• pp.72-79
• /
• 2022

A cold roll-bonding process using AA1050, AA5052 and AA6061 alloy sheets is performed without lubrication. The roll-bonded specimen is a multi-layer complex aluminum alloy sheet in which the AA1050, AA5052 and AA6061 sheets are alternately stacked. The microstructural evolution with the increase of annealing temperature for the roll-bonded aluminum sheet is investigated in detail. The roll-bonded aluminum sheet shows a typical deformation structure in which the grains are elongated in the rolling direction over all regions. However, microstructural evolution of the annealed specimen is different depending on the type of material, resulting in a heterogeneous microstructure in the thickness direction of the layered aluminum sheet. Complete recrystallization occurs at 250 ℃ in the AA5052 region, which is lower by 100K than that of the AA1050 region. Variation of the misorientation angle distribution and texture development with increase of annealing temperature also differ depending on the type of material. Differences of microstructural evolution between aluminum alloys with increase of annealing temperature can be mainly explained in terms of amounts of impurities and initial grain size.

• 한국표면공학회지
• /
• 제57권1호
• /
• pp.8-13
• /
• 2024

Anodizing of Al6061 alloy was conducted in two different electrolytes of 20% sulfuric acid and 8% sulfuric acid + 3 % oxalic acid solutions at a constant current or decreasing current density conditions, and its dielectric breakdown voltage was measured. The surface morphology of anodic oxide films was observed by TEM and thermal treatment was carried out at 400 ℃ for 2 h to evaluate the resistance of the anodic oxide films to crack initiation. The anodic oxide film formed in 8% sulfuric acid + 3 % oxalic acid solution showed higher dielectric breakdown voltage and better resistance to crack initiation at 400 ℃ than that formed in 20% sulfuric acid solution. The dielectric breakdown voltage increased 6 ~12% by applying decreasing current density comparing with a constant current density.