• 한국재료학회지
• /
• 제32권2호
• /
• pp.72-79
• /
• 2022

A cold roll-bonding process using AA1050, AA5052 and AA6061 alloy sheets is performed without lubrication. The roll-bonded specimen is a multi-layer complex aluminum alloy sheet in which the AA1050, AA5052 and AA6061 sheets are alternately stacked. The microstructural evolution with the increase of annealing temperature for the roll-bonded aluminum sheet is investigated in detail. The roll-bonded aluminum sheet shows a typical deformation structure in which the grains are elongated in the rolling direction over all regions. However, microstructural evolution of the annealed specimen is different depending on the type of material, resulting in a heterogeneous microstructure in the thickness direction of the layered aluminum sheet. Complete recrystallization occurs at 250 ℃ in the AA5052 region, which is lower by 100K than that of the AA1050 region. Variation of the misorientation angle distribution and texture development with increase of annealing temperature also differ depending on the type of material. Differences of microstructural evolution between aluminum alloys with increase of annealing temperature can be mainly explained in terms of amounts of impurities and initial grain size.

• 한국재료학회지
• /
• 제21권12호
• /
• pp.655-659
• /
• 2011

An ultrafine grained complex aluminum alloy was fabricated by an accumulative roll-bonding (ARB) process using dissimilar aluminum alloys of AA1050 and AA5052 and subsequently annealed. A two-layer stack ARB process was performed up to six cycles without lubricant at an ambient temperature. In the ARB process, the dissimilar aluminum alloys, AA1050 and AA5052, with the same dimensions were stacked on each other after surface treatment, rolled to the thickness reduction of 50%, and then cut in half length by a shearing machine. The same procedure was repeated up to six cycles. A sound complex aluminum alloy sheet was fabricated by the ARB process, and then subsequently annealed for 0.5h at various temperatures ranging from 100 to $350^{\circ}C$. The tensile strength decreased largely with an increasing annealing temperature, especially at temperatures of 150 to $250^{\circ}C$. However, above $250^{\circ}C$ it hardly decreased even when the annealing temperature was increased. On the other hand, the total elongation increased greatly above $250^{\circ}C$. The hardness exhibited inhomogeneous distribution in the thickness direction of the specimens annealed at relatively low temperatures, however it had a homogeneous distribution in specimens annealed at high temperatures.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.369-372
• /
• 2005

A study on the microstructure, the texture and the formability of the samples after ECAPed and subsequent heat-treated AA 1050 aluminum alloy sheet have been carried out. The specimens after the ECAP showed a very fine grain size, a decrease of <100> // ND. The <110>// ND textures appears in the specimens after the ECAP and subsequent heat-treatment at $400^{\circ}C$ for 1 hour. One of the most important properties in sheet metals is formability. The r-value or plastic strain ratio has was as a parameter that expressed the formability of sheet metals. The change of the plastic Strain ratios after the ECAP and subsequent heat-treatment conditions were investigated and it was found that they were two times higher than those of the initial Al sheets. This could be attributed to the formation above texture components through the ECAP and subsequent heat-treatment of AA 1050 Aluminum alloy sheet.

• 소성∙가공
• /
• 제14권6호
• /
• pp.553-558
• /
• 2005

A study on the microstructure, the texture and the formability of the samples after ECAPed and subsequent heat-treated AA 1050 aluminum alloy sheet have been carried out. The specimens after the ECAP showed a very fine grain size, a decrease of <100> // ND, and an increase of <111> // ND textures. The $\{111\}<112>,\;\{123\}<634>,\;\{110\}<001>,\;\{112\}<111>,\;\{110\}<111>,\;and\;\{013\}<231>$ texture components were increased in the specimens after the ECAP and subsequent heat-treatment at $400^{\circ}C$ for 1 hour. One of the most important properties in sheet metals is formability. The r-value or plastic strain ratio has was as a parameter that expressed the formability of sheet metals. The change of the plastic strain ratios after the ECAP and subsequent heat-treatment conditions were investigated and it was found that they were two times higher than those of the initial Al sheets. This could be attributed to the formation above texture components through the ECAP and subsequent heat-treatment of AA 1050 Aluminum alloy sheet.

• 한국재료학회지
• /
• 제26권12호
• /
• pp.688-695
• /
• 2016

Recrystallization behavior has been investigated for commercial purity AA1050 (99.5wt%Al) and high purity 3N Al (99.9wt% Al). Samples were cold rolled with 90% of thickness reduction and were annealed isothermally at 290, 315, and 350o C for various times until complete recrystallization was achieved. Hardness measurement and Electron Backscatter Diffraction(EBSD) analyses, combined with Grain Orientation Spread(GOS), were employed to investigate the recrystallization behavior. EBSD analysis combined with GOS were distinctly revealed to be a more useful method to determine the recrystallization fraction and to characterize the recrystallization kinetics. As the annealing temperature increased, recrystallization in AA1050 accelerated more than that process did in Al 3N. Both AA1050 and Al 3N showed the same temperature dependence of the n value of the Johnson-Mehl-Avrami-Kolmogorov equation(JMAK equation), i.e., n values increased as annealing temperature increased. Activation energy of recrystallization in AA1050 is about 176 kJ/mol, which is comparable with the activation energy of grain boundary migration in cold-rolled AA1050. This value is somewhat higher than the activation energy of recrystallization in Al 3N.

• 대한금속재료학회지
• /
• 제48권7호
• /
• pp.605-614
• /
• 2010

Conventional rolling (symmetric) and differential speed rolling (DSR) were both applied to AA1050 sheets at various velocity ratios, from 1 to 2 between the top and bottom rolls. An electron backscatter diffraction (EBSD) technique was used to measure texture inhomogeneity through the thickness direction. After the annealing process, the annealing texture of the DSR processed sheets was different from that of conventionally rolled sheets. The velocity ratio between the top and bottom rolls affected the texture inhomogeneity and macroscopic plastic strain ratio of the AA1050 sheets. A prediction for the macroscopic plastic strain ratio of AA1050 sheets was carried out using a visco-plastic self-consistent (VPSC) polycrystal model. The strain ratio directionality that was predicted using the VPSC polycrystal model was in good agreement with experimental results.

• 소성∙가공
• /
• 제13권4호
• /
• pp.382-387
• /
• 2004

The continuous confined strip shearing (CCSS) based on the equal channel angular pressing (ECAP) was modeled by means of a rigid-plastic two-dimensional finite element method (FEM). Parallel to the simulations, samples of AA 1050 sheets were experimentally deformed by CCSS. The CCSS deformation led to the formation of through thickness texture gradients comprising a strong shear texture in the sheet center and weak shear textures in the sheet surfaces. FEM analysis revealed variations in the strain component $\varepsilon_13$ along the sample thickness direction, which gave rise to the evolution of different textures. A high friction between the sample and die surface was responsible for lowering intensities of the shear texture components in thickness layers close to the surfaces.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.219-221
• /
• 2006

Asymmetrical rolling was performed by rolling AA 1050 sheets with different velocities of upper and lower rolls. In order to study the effect of roll gap geometry on the evolution of strain states and textures during asymmetrical rolling, the reduction per rolling pass was varied. After asymmetrical rolling, the outer thickness layers depicted shear textures and the center thickness layers displayed a random texture. With decreasing reduction per an asymmetrical rolling pass, the thickness layers depicting shear textures increases. The strain states associated with asymmetrical rolling were investigated by simulations with the finite element method (FEM).

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.222-225
• /
• 2006

The effect of lubrication on the development of textures and Microstructure was studied by different lubricating condition during hot rolling of AA1050 aluminum alloy. Hot rolling without lubrication led to the evolution of the pronounced through-thickness texture gradients, whereas hot rolling with lubrication gave rise to the formation of uniform rolling texture in the whole thickness layer. The variation of texture and microstructure according to hot rolling condition are investigated by X-ray diffractometer (XRD) and Electron Back-Scattered Diffraction (EBSD). The experimental results were discussed base on the finite element method (FEM) simulation. FEM calculation reveals that a larger friction between roll and sheet causes the deviated strain state from a plane strain leading to the formation of shear textures in the thickness layers close to the surface.

• 한국재료학회지
• /
• 제18권9호
• /
• pp.492-496
• /
• 2008

The through-thickness variations of strain and microstructure of high-speed hot rolled 1050 pure aluminum sheet were investigated. The specimens of 1050 aluminum were rolled at temperatures ranging from 410 to $560^{\circ}C$ at a rolling speed of 15 m/s without lubrication and quenched in water at an interval of 30ms after rolling. The redundant shear strain induced by high friction between rolls and the aluminum sheet was increased largely beneath the surface at a rolling reduction above 50%. Recrystallization occurred in the surface regions of the specimen rolled to reduction of 65% at $510^{\circ}C$, while only recovery occurred in the other regions.