• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.23 no.3
• /
• pp.117-126
• /
• 1987

The author has analysed profile of flow in rear of motion with single ball with low Reynolds number performed interface layers. For each system whose viscosity of the lower phase is as large as or large that of the upper phase, the profile has based on the thickness of the ball in the lower phase is nearly independent of both the ball single and the physical properties of the upper phase of the solution. The examine of the characteristics between Darwin's total displacement of the fluid and data obtained in this study, the averaged volume of each cases was corrected by the viscosity in the lower phase. When the viscosity in the lower phase is less than that of the upper phase, the volume based on the displacement of the fluid in rear region of ball are influenced by both ball size and the viscosity ratio of the upper phase to the lower phase. In the range of the Reynolds number less than a constant values, the volume ratio is influenced by both Reynolds number and Moltion number but mainly Reynolds. In range of Reynolds number over than the value, the volume ratio is independent of Reynolds number, but influenced by Moltion number.

• Korean Chemical Engineering Research
• /
• v.57 no.3
• /
• pp.344-350
• /
• 2019

Durability is very important for the commercialization of membranes and electrode assemblies (MEA) developed for proton exchange membrane fuel cells (PEMFC). Durability evaluation of stationary PEMFC MEA has a problem that the voltage change rate should be measured for a long time over 1000 hours under constant current conditions. In this study, the electrochemical durability evaluation protocol of membranes (OCV holding method) using to vehicle MEAs was applied to the stationary MEA for the purpose of shortening the durability evaluation time. After operation of the stationary and automobile MEA for 168 hours under conditions of OCV, cathode oxygen, $90^{\circ}C$ and relative humidity of 30%, I-V, LSV, CV, impedance and FER were measured and compared. When the hydrogen permeability, OCV change, ionic conductivity, and fluorine flow rate, which represent the durability of the membrane after degradation, were all examined, it was shown that durability of stationary MEA membrane was better than that of vehicles MEA membrane. In addition, the electrode degradation of stationary MEA was smaller than that of vehicles MEA after degradation operation. It was possible to evaluate in a short time using automotive protocol that the durability of stationary MEA was superior that of vehicle MEA in terms of membrane and the electrode.

• (The)Study of the Eastern Classic
• /
• no.34
• /
• pp.339-362
• /
• 2009

If we try to define the concept of beauty in the large sense, as Kant and Chaung-tzu all agree, It can not be fixed in the one sense, but whose connotation and denotation should be extended infinitely. In this sense, I would like to say that the beauty is liberty. Aesthetics of Kant is oriented toward subjective and reflexive dimension, while that of Chuang-tzu is oriented toward natural and practical one. The difference between aesthetics of the two philosophers begins from their philosophical methodology. If the transcendental methode which is proper to Kant's philosophy prefers to discriminate and devide everything especially from dichotomic viewpoint by langage. But Chuang-tzu' methode called Za-Mang criticizes such a dichotomic division and langage itself. Even so, the two in the long run agree as to the foundation of beauty. But Kant's liberty is one of will or transcendental, meanwhile that of Chuang-tzu is based on recognize the fact that we are all production of nature. according to Chuang-tzu, in the great beginning, there was non-being. It had neither being nor name. The One originates from it. When things obtain it and come into existence. As the One, Tao is in the excrement and urine. Everything is under the constant flux. All species have originative or moving power. Although the universe is vast, its transformation is uniform. Because all things are one. Vacuity, tranquillity, mellowness, quietness, and taking no action characterize the things of universe at peace and represent the ultimate of Tao and virtue. The material was transformed to be form, form was transformed to become life, and now life has transformed to become death. A basic principle of Chuang-tzu's art is expressed in the phrase "taking off clothes and squatting down bare-backed". The key of Chuang-tzu's aesthetics is to dedicate to the expression of inner spirit instead of physical verisimilitude, and painting should be a spontaneous and instantaneous flow of the brush. Kant's concepts such as "disinterested" and "purposiveness of nature" seem to imply in the long run the unification of nature and human being which is fundament to Chuang-tzu's aesthetics.

• Journal of Life Science
• /
• v.22 no.7
• /
• pp.871-879
• /
• 2012

Polyploids are a potentially important germplasm source in seedless citrus breeding program. Seedlessness is one of the most promising traits of commercial mandarin breeds that mandarin triploid hybrids possess permanently. The formation of new constant triploid hybrids can be recovered through diploid species hybridization from the fusion of divalent gametes at low frequencyor intra-and inter-ploidy crosses. However, extensive breeding work based on small $F_1$ hybrid seeds developed is impossible without a very effective aseptic methodology and ploidy event. In this study, in vitro embryo culture was employed to recover natural hybrids from monoembryonic diploid, open-pollinated mandarin. Flow cytometry was used to determine ploidy level. A total of 10,289 seeds were extracted from 792 fruits having approximately 13 seeds per fruit. Average frequency of small seeds developed was 7.1%, while the average frequency of small seeds per fruit were: 8.9% for 'Clementine' 10.2% for 'Harehime' 2.6% for 'Kamja' 3.1% for 'Pyunkyool' 2.8% for 'Sadookam' and 7.0% for 'Wilking' mandarin. Average size of a perfect seed was $49.52{\pm}0.07mm^2$ ('Clementine') while the small seed measured $7.95{\pm}0.04mm^2$ ('Clementine'), which was about 1/6 smaller than the perfect seed. In total, 731 small seeds were obtained and all of them contained only one embryo per seed. The efficiency of 'Clementine' was 14 times higher than 'Wilking' and more than 109 times higher than 'Pyunkyool'. The basic information on spontaneous polyploidy provides for the hybridization of constant triploids and increases the efficiency of conventional cross.

• The Korean Journal of Nuclear Medicine
• /
• v.25 no.1
• /
• pp.117-121
• /
• 1991

Technetium-99m-hexamethylpropyleneamine oxime $(^{99m}Tc-HM-PAO)$ is a neutral-lipophilic chelate which is used for scanning cerebral blood flow. The labeling efficiencies of $^{99m}Tc-HM-PAO$ is known to be sensitive to the amount of pertechnetate added and the quality of the pertechnetate. Because of these factors, the manufacture recommends that HM-PAO kits be reconstituted with a maximum of 30 mCi pertechnetate which was eluted <4 hr earlier from a generator which had been eluted < 24 hr previously. So we measured the labelling efficiencies and the decomposition rate constant according to the amount of pertechnetate added, the volume of pertechnette added, and generator in-growth time. We used the 3-system chromatographic methods (paper & ITLC-SG chromatography) which analyzed the labelling efficiencies of the $^{99m}Tc-HM-PAO$. There was no significant difference in labelling efficiencies between variable pertechnetate acitvities added. ($39.9{\pm}4.9\;mCi:\;87.8{\pm}5.1\;(%)$, $60.8{\pm}5.0\;mCi:\;90.7{\pm}2.2\;(%)$, $79.0{\pm}6.0\;mCi:\;86.8{\pm}3.9\;(%)$, $106.6{\pm}11.6\;mCi:\;87.7{\pm}1.2\;(%)$, p>0.05) No significant difference in labelling efficiencies were found between pertechnetate of 4ml and 5ml. (4ml : $89.1{\pm}3.2(%)$, 5ml: $87.3{\pm}4.0(%)$, p>0.05). There was no difference between 1-6 and 10-48 hr of generator in-growth time. (1-6 hr: $87.8{\pm}4.0(%)$, 10-48 hr: $89.6{\pm}1.6(%)$, p>0.05) The mean value of decomposition rate constant was $0.196{\pm}0.097\;(hr^{-1})$, and there were no difference according to the amount of pertecnetate added and the volume of pertecnetate added, ($39.9{\pm}4.9\;mCi:\;0.208{\pm}0.059\;(hr^{-1})$, $60.8{\pm}5.0\;mCi:\;0.191{\pm}0.100\;(hr^{-1})$ $79.0{\pm}6.0\;mCi:\;0.192{\pm}0.118\;(hr^{-1})$, $106.6{\pm}11.6\;mCi:\;0.212{\pm}0.030\;(hr^{-1})$, p>0.05, 4 ml: $0.200{\pm}0.074\;(hr^{-1})$, Sml: $0.193{\pm}0.115\;(hr^{-1})$, p>0.05). In the case of using the first eluate, the labelling efficiency of $^{99m}Tc-HM-PAO$ W3S 82.1%. These data suggest that there were no significant alteration in labelling efficiency of $^{99m}Tc-HM-PAO$ according to the considerable range of pertechnetate activities and volume added, and generator in-growth time. Also, it was shown that one vial of HM-PAO kit supplied the $^{99m}Tc-HM-PAO$ which was used for 3-4 patients.

• Journal of the Korean Geosynthetics Society
• /
• v.15 no.3
• /
• pp.27-37
• /
• 2016

Although many studies on the Granular Compaction Pile (GCP) have been done by many researchers, the GCP design has not been systematically done due to the absence of the rational design methodology. As the GCP design has been mostly done by engineers' own experiences, some failure cases have been reported to occur. For this reason, it is very difficult to confirm definite causes of the failure and establish the prevention plans for the failure. Therefore, this study aims to investigate the optimal mixing ratio of gravel and sand, the effects of the internal friction angle of the GCP on the stress concentration ratio and the vertical and horizontal settlements. In order to analyze the behavior of the soft ground reinforced with the GCP depending on the different design parameters such as the stress concentration ratio and the internal friction angle, a number of finite element (FE) analyses were performed. From the direct shear test, the optimal mixing ratio of gravel to sand was found to be 70:30. Based on the numerical analyses, as the internal friction angle increased, the stress concentration ratio increased and it converged to a constant value. In addition, the larger the internal friction angle, the smaller the settlements. Consequently, the use of the optimal mixing ratio of gravel and sand can lead to reducing both the lateral flow and the heaving phenomenon.

• Korean Chemical Engineering Research
• /
• v.49 no.5
• /
• pp.510-515
• /
• 2011

The pyrolytic reaction of 1,1-dichloroethylene($CH_2CCl_2$) has been conducted to investigate thermal decomposition of chlorocarbon and product formation pathways under hydrogen reaction environment. The reactions were studied in a isothermal tubular flow reactor at 1 atm total pressure in the temperature range $650{\sim}900^{\circ}C$ with reaction times of 0.3~2.0 sec. A constant feed molar ratio $CH_2CCl_2:H_2$ of 4:96 was maintained through the whole experiments. Complete decay(99%) of the parent reagent, $CH_2CCl_2$ was observed at temperature near $825^{\circ}C$ with 1 sec. reaction time. The important decay of $CH_2CCl_2$ under hydrogen reaction environment resulted from H atom cyclic chain reaction by abstraction and addition displacement. The highest concentration (28%) of $CH_2CHCl$ as the primary product was observed at temperature $700^{\circ}C$, where up to 46% decay of $CH_2CCl_2$ was occurred. The secondary product, $C_2H_4$ as main product was detected at temperature above $775^{\circ}C$. The one less chlorinated ethylene than parent increase with temperature rise subsequently. The HCl and dechlorinated hydrocarbons such as $C_2H_4$, $C_2H_6$, $CH_4$ and $C_2H_2$ were the main products observed at above $825^{\circ}C$. The important decay of $CH_2CCl_2$ resulted from H atom cyclic chain reaction by abstraction and addition displacement. The important pyrolytic reaction pathways to describe the features of reagent decay and intermediate product distributions, based upon thermochemical and kinetic principles, were suggested.

• Water for future
• /
• v.15 no.3
• /
• pp.49-55
• /
• 1982

The purpose of this study is to examine the methods of estimation, comparing U.S. SCS method and $\Phi$-index with effective rainfall. And also comparision was made among SCS method, Chow method and Mockus method as to the peak discharge of design storm hydrograph by small river basin. Hydrological data of the Shin river basin which was used in this study and the results of study are as follow; 1) As a result of applying the SCS method to determine the effective rainfall out of total rainfall, it turned out that the everage CN of the basin as obtained by the analysis of hydrologic soil-cover complex was varied as follows; AMC-I was 27.9%, AMC-II 16.4%, AMC-III 8.1% less than the value given by SC method using discharge measurement. 2) The comparision of effective rainfall by the ungaged SCS method with that of gauged $\Phi$-index method showed that the $\Phi$-index method showed that the $\Phi$-index method gives large value by 4.7% to those given by hydrograph. The result of analysis by the SCS method resulted in great difference from discharge measurement. 3) The comparision of SCS method, Chow method, and Mockus method showed that dimensionless hydrograph of SCS method and Chow method were close to the peak discharge of the gauged unit hydrograph, while the other methods gave far different results. 4) Attempts were made, for a better adaptation to the Shin river basin, to introduce lag time formula constant of dimensionless hydrograph of the SCS method by using the peak discharge of the gauged flow hydrograph.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.11
• /
• pp.110-117
• /
• 2017

In the construction of high-rise residential buildings in which the finishing works are done repetitively in each housing unit, the construction period and cost can be reduced, while maintaining the quality, if the work process is properly managed in order for the resources to be input continuously. Time management methods such as the Bar Chart, CPM and LOB are not appropriate, due to the difficulties involved in the diagraming of repetitive works and applying them to the project. The Tact method also has difficulties in maintaining a constant work flow and needs significant effort and cooperation from the subcontractors to allocate the resources consistently. Partitioning, base works for finishing, floor mortar plastering and the final finishing work are done sequentially in residential buildings projects, and there are many repetitive activities which differ in terms of the work method, work area and productivity. If these repetitive activities are synchronized or converged toward the last work area, the goal of process management can be achieved effectively. Therefore, a process planning method for the finishing works of residential building projects is proposed, which takes into consideration elements, such as the sequential relation between the activities in each housing unit and classification of repetitive works in terms of their management method, work area and production rate, for the continuous input of resources into the housing units.

• The Journal of Engineering Geology
• /
• v.26 no.3
• /
• pp.307-314
• /
• 2016

Shear characteristics of soils can be investigated using various types of shear stress measuring apparatus. Ring shear tests are often applied for examining the residual shear strength under the unlimited deformation. This paper presents drainage-consolidation-shear velocity dependent undrained shear strengths measured in terms of water leakage. A series of ring shear tests were performed under the constant normal stress (50 kPa) and controled shear velocity ranging from 0.01~1 mm/sec under the undrained condition. As a result, undrained shear strengths are dependent on shear velocity. It exhibits that straining hardening behavior is observed for the shear velocity lower than 0.1 mm/sec; however, the strain softening behavior is observed for the shear velocity higher than 0.1 mm/sec. Water leakage can cause the increase in shear stress irrespective of shear velocity. Shear stress increases with increasing amount of water leakage. It is due to the fact that the small grains and water flow out through the rubble edge in the ring shear box. Repetitive saturation and consolidation processes may minimize the error.