• 태양에너지
• /
• 제18권4호
• /
• pp.11-22
• /
• 1998

Floor panel heating system using hot water is the primary heating system of domestic residential building. This paper presents the results of performance analysis of the heat pump system with air source evaporator and single unit dual sink(SUDSk) condenser. The heat exchanger combines two separated condensers into a single condenser and the object of the SUDSk condenser is to release energy to dual sinks, i.e. air for air heating system and water for panel heating system in one single unit. Simulation program is developed for single unit dual source(SUDS) SUDSk heat pump system and some experimental data are obtained and compared with simulation results. Differences of heating capacity and COP in dual source operating mode are 7% and 8% respectively. Simulation results are in good agreement with test results. Therefore, developed program is effectively used for design and performance prediction of dual source dual sink heat pump system with SUDS evaporator and SUDSk condenser.

• Nuclear Engineering and Technology
• /
• 제54권12호
• /
• pp.4585-4600
• /
• 2022

A pool scrubber is often used as a wet-type design to mitigate the consequence of a severe nuclear accident. While studies indicated higher decontamination performance of a deeper pool, utilizing a very tall pool can be problematic due to potential structural stability and water backflow issues. This study proposes, as an alternative to a single pool system, a pool scrubber system composed of serially connected multiple pools with lower heights. Since large fraction of aerosol removal takes place in the injection region, serially connected pool scrubber system is expected to enhance the overall decontamination capability of a pool scrubber system. To support the analysis of the proposed system's decontamination capability, a new computer model was developed in the study to describe the bubble size dependent effect on aerosol removal including the effect of pool residence time. The accuracy of the new model was examined against experimental data for its validation. The proposed scrubber system composed of serially connected multiple shorter pools is found to have much improved decontamination performance over the current single pool system design.

• 대한기계학회논문집B
• /
• 제25권4호
• /
• pp.467-474
• /
• 2001

The mathematical model of a air-conditioning system is generally very complex and difficult to apply to controller design. In this paper, simple models applicable to the controller design are obtained by modeling the air-conditioning system by single-input single-output between compressor speed and indoor temperature, and by multi-input single-output between compressor speed, indoor fan speed and indoor temperature. Using these empirical models, model predictive control(MPC) technique was implemented for indoor temperature control of the air-conditioning system. It has been shown from various experiments that the indoor temperature control based on the MPC scheme yields reasonably good tracking performance with smooth changes in plant inputs. this multi-input multi-output MPC approach can be extended to multi air- conditioning systems where the conventional PID control scheme is very difficult to apply.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.572-578
• /
• 2008

As the railway transportation is getting faster and its operation speed has increased rapidly, its signal control has been complicated. For real time signal processing it is very important to prohibit any critical error from causing the system to malfunction. Therefore, handling complicated signals effectively while maintaining fault-tolerance capability is highly expected in modern railway transportation industry. In this paper, we suggest an SoC (Sytem-on-Chip) design method to integrate these complicated signal controlling mechanism with fault tolerant capability in a single chip. We propose an SoC solution which contains a high performance 32-bit embedded processor, digital filters and a PWM unit inside a single chip to implement ATO's, ATC's, ATP's and ATS's digital signal-processing units. We achieve an enhanced reliability against the calculation error by adding fault tolerance features to ensure the stability of each module.

• Journal of applied mathematics & informatics
• /
• 제14권1_2호
• /
• pp.353-363
• /
• 2004

The purpose of this paper is to present a model to design the layout of the user interface components that handles many numbers of qualitative factors. An alternate rating system is also proposed for the closeness relationship ratings between the various pairs of components evaluated by using GOMS (goals, operators, methods and selection rules) technique. The proposed model is applied to the design of the part of the user interface in order to obtain the best layout of the components. The results of the proposed model are compared with that of an existing model, which handles single qualitative factor applied to obtain the layouts of user interface components.

• Journal of Biosystems Engineering
• /
• 제33권2호
• /
• pp.94-100
• /
• 2008

Present chemical application method using a power sprayer has been labor intensive, costly and ineffective. Therefore, a small agricultural unmanned helicopter was suggested to replace the conventional spray system. In this study, conceptual design for developing the helicopter and a consequential prototype were reported. The overall conceptual design was initiated by deciding the type of agricultural helicopter, as the single rotor helicopter with a tail system. As the first step of the designing, an air-cooled, 2-stroke engine was selected and a prototype transmission was designed by determining the rotating speed of main rotor shaft. A 'pusher' type tail rotor system was adapted to balance the reaction torque and reduce the power use. The tail boom length was designed to avoid the rotating trajectory of the main rotor. The RF console consisted of the engine control, attitude control, and emergency control modules. Assembling the prototype concluded the mechanical development of the agricultural helicopter.

• 천문학회지
• /
• 제29권spc1호
• /
• pp.389-390
• /
• 1996

The CCDs are widely used in astronomical observations either in direct imaging use or spectroscopic mode. However, the areas of available sensors are too small for large imaging format. One possibility to obtain large detection area is to assemble mosaics of CCD, and drive them simultaneously. Parallel driving of many CCDs together rules out the possibility of individual tuning; however, such optimisation is very important, when the ultimate low light level performance is required, particularly for new, or mixed devices. In this work, a new concept is explored for an entirely novel approach, where the drive waveforms are multiplexed and interleaved. This simultaneously reduces the number of leadout connections and permits individual optimisation efficiently. The digital controller can be designed within a single EPLD (Erasable Programmable Logic Device) chip produced by a CAD software package, where most of the digital controller circuits are integrated. This method can minimise the component. count., and improve the system efficiency greatly, based on earlier works by Han et a1. (1996, 1994). The system software has an open architecture to permit convenient modification by the user, to fit their specific purposes. Some variable system control parameters can be selected by a user with a wider range of choice. The digital controller design concept allows great flexibility of system parameters by the software, specifically for the compatibility to deal with any number of mixed CCDs, and in any format, within the practical limit.

• 한국광학회지
• /
• 제5권2호
• /
• pp.204-211
• /
• 1994

팩시밀이나 복사기용으로 이용되는 micro lens array를 설계하였다. array 형태는 육각형배열이고 유효경은 0.160mm, 가장 가까운 이웃렌즈의 중심간 거리는 0.192mm로 하였다. 결상계의 횡배율은 1.0이다. single layer는 working distance가 10.55mm, double layer는 working distance가 7.90mm가 되었다. 각각의 성능은 ray fan을 계산하여 그 특성을 조사하였으며 서로 비교하였다.

• 품질경영학회지
• /
• 제31권4호
• /
• pp.184-193
• /
• 2003

PL has been developed centering around England and America. Recently many countries are introducing PL system changing the world a single economic bloc based on the rapid development of Technology and Economy. This paper is studied with related literatures and theses, organizational consulting cases within the framework of the firm as the central operating bodies of PL system. In the past, Some papers about System Integration which was operated as a same Certificate System and enacted in a single organization, was studied and presented. But most of papers was a theoretical study related model and conception. In this situation Government supports PSMS of a single system at government expense to 100­200 companies for improving organizational confrontation ability of PL this year. This paper proposed a design and effect of Integration system model based on the analysis of ISO 9001：2000, KS, PSMS and ISO 14001. The integrated system has the following three distinctions. Firstly, KS is a national establishment, national leading certification and forcing standard. Secondly, ISO 9001：2000 and ISO 14001 are an international organization's establishment, non­official certification and optional standard. Finally, PSMS isn't a national law and forcing matter. And it isn't the concept of certification but the operational system by itself. Also if a lawsuit by defect is happened, it is very dangerous. This paper, which is integrated by four management systems and has many consulting cases, is the first in this department and is different from others. Also If people has the basic knowledge about management system, they can directly connect it to the organizational system according to this paper's guidance. It is very good result in this study because the law of PL is executed now.

• 한국실내디자인학회논문집
• /
• 제16권4호
• /
• pp.110-118
• /
• 2007

Technology has been viewed at various stages of civilization as leading to future progress. The building, its services systems and management of the work process all contribute to the well-being of people within an organization. Productivity relies on there being a general sense of high morale and satisfaction with the workplace. Now buildings are considered as providing a milieu for human creativity. Flexibility, adaptability, service integration and high standards of finishes offer an intelligence threshold. Building Automation System(BAS) - controlled lighting systems may offer incremental energy saving. Conventional Lighting control systems often control equipment in a single room or over the limited area, because they are centralized control systems, which means that all the controlled circuits must be wired to a single control panel. The computers used by these systems are typically dedicated microprocess that perform only lighting control functions. By comparison, modern Building automation systems are distributed control system, which means that their computing hardware and software are distributed as a network that microprocessor-based control modules and standard PC. PLC(Programmable Logic controller) is extensible virtually without limits, so that all the lighting in a facility can be controlled by single, unified system - the same system that also can control and monitor the building's HVAC, security, and manufacturing processed, elevators, and more. A Building automation system can control light using schedules, manual controls, occupancy sensors, and photosensors, either singly or in combination. Building Lighting control and monitoring system will be for a energy saving and efficient building management system.