• 한국전기전자재료학회논문지
• /
• 제14권2호
• /
• pp.104-110
• /
• 2001

Structural, optical and electrical properties of Cd$_{1-x}$ Zn$_{x}$S films deposited by chemical bath deposition(CBD), which is a very attractive method for low-cost and large-area solar cells, are presented. Especially, in order to control more effectively the zinc component of the films, zinc acetate, which was used as the zinc source, was added in the reaction solution after preheating the reaction solution and the pH of the reaction solution decreased with increasing the concentration of zinc acetate. The films prepared after preheating and pH control had larger zinc component and higher optical band gap. The crystal structures of Cd$_{1-x}$ Zn$_{x}$S films was a wurtzite type with a preferential orientation of the (002) plane and the lattice constants of the films changed from the value for CdS to those for ZnS with increasing the mole ratio of the zinc acetate. The minimum lattice mismatch between Cd$_{1-x}$ Zn$_{x}$S and CdTe were 2.7% at the mole ratio of (ZnAc$_2$)/(CdAc$_2$+ZnAc$_2$)=0.4. As the more zinc substituted for Cd in the films, the optical transmittance improved, while the absorption edge shifted toward a shorterwavelength. the photoconductivity of the films was higher than the dark conductivity, while the ratio of those increased with increasing the mole ratio of zinc acetate. acetate.

• 대한기계학회논문집B
• /
• 제21권7호
• /
• pp.948-961
• /
• 1997

The effects of intake port eccentricity and a partition between the two intake ports on the incylinder swirl characteristics in a 4 valve diesel engine having the two intake ports, one is a helical intake port and the other is a tangential intake port, were investigated by using the impulse swirl meter(ISM) in a steady flow test rig. Mean flow coefficient ( $C_{f(mean)}$, swirl ratio ( $R_{s}$) and the mass flowrate through the two intake ports with and without intake port partition were measured. The results showed that the characteristics of in-cylinder swirl ratio formed by a 4-valve cylinder head were largely affected by valve eccentricity ratio ( $N_{y}$) and the existence of an intake port partition between the two intake ports. Mean flow coefficient ( $C_{f(mean)}$) increases and swirl ratio ( $R_{s}$) decreases in case of being the partition between the two intake ports. And also the mass flowrate through the tangential intake port is 19.0% and 7.7% more than that of the helical intake port in case of the two intake ports with and without partition respectively.ively.

• 한국세라믹학회지
• /
• 제28권4호
• /
• pp.315-323
• /
• 1991

The preparation of zirconium carbide powders by the halogenide process of ZrCl4-C-Mg system (1:1:2, molar ratio) was studied between 300。 and 120$0^{\circ}C$ under Ar gas flow (200 mι/min). The formation mechanism and kinetics of zirconium carbide and characteristics of the synthesized powder were examined by TG-DTA, XRD, SEM and PSA. 1) The formation mechanism of zirconium carbide were as follows, above 30$0^{\circ}C$ ZrCl4(S)+Mg(s)longrightarrowZrCl2(s)+MgCl2(s) above 40$0^{\circ}C$ ZrCl2(S)+Mg(s)longrightarrowZr(s)+MgCl2(s) above 50$0^{\circ}C$ Zr(s)+C(s)longrightarrowZrC(s) 2) The apparent activation energy of the reduction-carbonization at temperature of 800$^{\circ}$to 100$0^{\circ}C$ was 11.9 kcal/mol. 3) The lattice parameter and the crystallite size of ZrC which was produced from the mixture powder of ZrCl4, C and Mg (1:1:2, molar ratio) at 100$0^{\circ}C$ for 1 h were 4.700A and 180A, respectively. 4) The powders obtained from the mixture powder of ZrCl4, C and Mg(1:1:2, molar ratio) at 100$0^{\circ}C$ for 1 h were agglomerate with the average size of about 13${\mu}{\textrm}{m}$ in SEM micrograph.

• 정보처리학회논문지A
• /
• 제10A권5호
• /
• pp.487-492
• /
• 2003

멀티미디어 콘텐츠 스트림 서비스를 이용하는 사용자들의 서비스 품질에 대한 요구를 만족시키기 위해 사용자 실적 또는 등급에 따라 자원을 배분하고 서비스 요청과 서비스 품질을 제어하기 위한 방안이 필요하다. 본 논문에서는 스트림 서버 자원을 효율적으로 분배하명서 사용자들에게 제공되는 서비스 품질을 제어하는 방안으로서 사용자 등급별 QoS 보장을 위한 서비스 요청 필터링 알고리즘(URFA : User Request Filtering Algorithm)을 제안한다. URFA는 사용자들의 요금 실적과 서비스 이용 실적 등을 고려하여 사용자 등급(우수 등급, 기본등급)을 나누고 등급별 스트림 서버의 승인비율을 제어함으로써 서버자원의 이용효율을 높이고 사용자 등급에 따라 품질 수준을 제어할 수 있도록 하였다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.351-356
• /
• 1999

In this study, the characteristics of chip formation of the cold drawn Bi-S free machining steels were assessed. And for comparison, those of the cold drawn Pb-S free machining steel, the hot rolled low carbon steel which has MnS as free machining inclusions and the conventional steels were also investigated. During chip formation, the cold drawn free machining steels show relatively little change in thickness and width of chip compare to those of the conventional carbon steels. And a single parameter which indicates the degree of deformation during chip formation, 'chip cross-section area ratio' is introduced. The chip cross-section area. The variational patterns of cross-section area is divided by undeformed chip cross-section area. The variational patterns of the chip cross-section area ratio of the materials cut are similar to those of the shear strain values. The shear stress, however, seems to be dependent on the carbon content of the materials. The cold drawn BiS and Pb-S steels show nearly the same chip forming behaviors and the energy consumed during chip formation is almost same. A low carbon steel without free machining aids shows poor chip breakability due to its high ductility. By introducing a small amount of non-metallic inclusions such as MnS, Bi, Pb or merely increasing carbon content the chip breakability improves significantly.

• 한국통신학회논문지
• /
• 제30권2A호
• /
• pp.61-65
• /
• 2005

본 논문에서는 DVB-RCS (Digital Video Broadcast-Return Channel via Satellite) 망에서 호 수락제어 (CAC)를 위한 Soft-QoS 기반의 borrowing 기법을 제안한다. 제안된 기법은 위성 망에서 사용 가능한 자원이 부족할 때 새로운 호를 받아들이기 위해 서비스 중인 호 중 일부에서 일시적이고 공평하게 대역폭을 가져온다. 각각의 호에서 가져오는 대역폭의 양은 각 사용자의 critical bandwidth ratio에 비례하며 critical bandwidth ratio는 제안된 기법에서 이용하는 QoS 파라메타 중 하나이다. 시뮬레이션 결과는 제안된 기법이 호의 blocking 확률과 대역폭 효율 측면에서 성능의 향상이 있음을 보여준다.

• Asian-Australasian Journal of Animal Sciences
• /
• 제27권4호
• /
• pp.600-607
• /
• 2014

The aim of this study was to assess the effect of substrate to inoculum ratio (S/I ratio) on the biochemical methane potential (BMP) and anaerobic biodegradability ($D_{deg}$) of different piggery slaughterhouse wastes, such as piggery blood, intestine residue, and digestive tract content. These wastes were sampled from a piggery slaughterhouse located in Kimje, South Korea. Cumulative methane production curves for the wastes were obtained from the anaerobic batch fermentation having different S/I ratios of 0.1, 0.5, 1.0, and 1.5. BMP and anaerobic biodegradabilities ($D_{deg}$) of the wastes were calculated from cumulative methane production data for the tested conditions. At the lowest S/I ration of 0.1, BMPs of piggery blood, intestine residue, and digestive tract content were determined to be 0.799, 0.848, and $1.076Nm^3kg^{-1}-VS_{added}$, respectively, which were above the theoretical methane potentials of 0.539, 0.644, and $0.517Nm^3kg^{-1}-VS_{added}$ for blood, intestine residue, and digestive tract content, respectively. However, BMPs obtained from the higher S/I ratios of 0.5, 1.0, and 1.5 were within the theoretical range for all three types of waste and were not significantly different for the different S/I ratios tested. Anaerobic biodegradabilities calculated from BMP data showed a similar tendency. These results imply that, for BMP assay in an anaerobic reactor, the S/I ratio of anaerobic reactor should be above 0.1 and the inoculum should be sufficiently stabilized to avoid further degradation during the assay.

• Structural Engineering and Mechanics
• /
• 제90권6호
• /
• pp.543-549
• /
• 2024

The utilization of the fabric materials for lightweight building structures has attracted considerable attention due to the multiple functions and high strength-to-weight ratio. The mechanical properties of the fabric materials evolve with the loading cycle, especially for the Poisson's ratio that requires the full cyclic strain to determine the accurate values. The digital image correlation method has been justified but needs to meet the flexibility and complexity requirements of the fabric materials. This paper thus proposes a modified digital image correlation method to quantify the Poisson's ratio of fabric materials. To obtain the accurate Poisson's ratio of fabric materials in the cyclic experiments using non-contact measuring method, a speckle generation of the digital image correlation method is implemented to obtain the strain distribution and strain characteristics. The uniaxial cyclic experiments for the fabric materials are carried out in the warp, weft and 45° directions. The digital image correlation photos are taken when the material properties become stable in the cyclic loading. The results show that the strain distributions are non-uniform and dependent on the specimen directions. The reliable Poisson's ratios of the fabric materials in the warp, weft and 45° directions are 0.016, 1.2 and 2.6. The strain asymmetry at the maximum strain position is related with the weaving architecture. These observations and results are indispensable to understand the Poisson's ratios of fabric materials and to guide the proper analysis of the large-span membrane structures.

• Current Photovoltaic Research
• /
• 제2권4호
• /
• pp.177-181
• /
• 2014

$Cu_2ZnSn(S_xSe_{1-x})_4$ (CZTSSe) absorber thin films were prepared on Mo coated soda lime glass substrates by sulfo-selenization of sputtered stacked Zn-Sn-Cu precursor thin films. The Zn-Sn-Cu precursor thin films were sulfo-selenized inside a graphite box containing S and Se powder using rapid thermal processing furnace at $540^{\circ}C$ in Ar atmosphere with pre-treatment at $300^{\circ}C$. The effect of different S/Se ratio on the structural, compositional, morphological and electrical properties of the CZTSSe thin films were studied using XRD (X-ray diffraction), XRF (X-ray fluorescence analysis), FE-SEM (field-emission scanning electron microscopy), respectively. The XRD, FE-SEM, XRF results indicated that the properties of sulfo-selenized CZTSSe thin films were strongly related to the S/Se composition ratio. In particular, the CZTS thin film solar cells with S/(S+Se)=0.25 shows best conversion efficiency of 4.6% ($V_{oc}$ : 348 mV, $J_{sc}$ : $26.71mA/cm^2$, FF : 50%, and active area : $0.31cm^2$). Further detailed analysis and discussion for effect of S/Se composition ratio on the properties CZTSSe thin films will be discussed.

• 대한핵의학회지
• /
• 제19권1호
• /
• pp.127-136
• /
• 1985

To evaluate change of serum $beta_2-microglobulin$ concentration$(s\beta_2-MG)$ and the usefulness of $s\beta_2-MG$ and $s\beta_2-MG/serum$ creatinine concentration(sCr) ratio in various renal diseases, $s\beta_2-MG$ and sCr were measured in 25 normal controls and 90 patients of various renal diseases(16 cases of glomerulonephritis, 12 cases of acute renal failure, 8 cases of chronic renal failure, 24 cases of nephrotic syndrome, 15 cases of tubulointerstitial diseases and 15 cases of lupus nephritis) using $Phadebas^\circledR$ $Beta_2-Micro$ Test kits. The results were as follows; 1) In normal control, the mean value of $s\beta_2-MG$ was $1.65{\pm}0.41mg/l$ and the mean value of $s\beta_2-MG/sCr$ ratio was $0.14{\pm}0.05$. 2) In various renal diseases, the mean value of $s\beta_2-MG$ was $6.74{\pm}5.47mg/l$. The mean value of $s\beta_2-MG/sCr$ ratio was $0.24{\pm}0.11$ and significantly elevated than that of normal control. (p<0.05) 3) The correlation between $s\beta_2-MG$ and sCr in glomerular and tubulointerstitial disease was log $s\beta_2-MG-0.90$ log sCr-0.48 and its correlation coefficient was 0.78(p<0.05). 4) In glomerular disease, the correlation between $s\beta_2-MG$ and sCr was log $s\beta_2-MG-0.89$ log sCr-0.46(r - 0.76) and in tubulointerstitial disease, it was log, $s\beta2-MG-0.95$ log sCr-0.59 (r-0.87). There was no significant difference between the two groups(p<0.05). 5) Among 32 cases of glomerular and tubulointerstitial disease patients, whose sCr was within normal range, 17 cases showed elevated $s\beta_2-MG$. The mean values of $s\beta_2-MG/sCr$ ratio in these patients was $0.30{\pm}0.14$ and significantly elevated than that of normal control(p<0.05). 6) In 15 cases of lupus nephritis, 12 cases showed elevated $s\beta_2-MG$ with normal sCr and 12 cases showed elevated $s\beta_2-MG/sCr$ ratio. With above results, it was found that the $s\beta_2MG$ can be used as an index of glomerular filtration rate as in the case of sCr and that $s\beta_2-MG/sCr$ ratio can be used as a tool in early detection of slightly decreased glomerular filtration rate and in detection of the renal disease of increased $\beta_2-MG$ production.