• The Magazine of the IEIE
• /
• v.2 no.2
• /
• pp.37-42
• /
• 1975

Various factors which affect the linearity and accuracy of the ramp type analog-to-digital converter have been investigated experimentally. A suggestion hav been made in the determination of circuit parameters with the emphasis on the improvement of the linearity and accuracy in the ramp type analog-to-digital conveter.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.6
• /
• pp.230-238
• /
• 1996

In this paper, digital corrction and calibration circuit for a high-resolution CMOS pipelined A/D converter are proposed. The circuits were actually applied to a 12 -bit 4-stage pipelined A/D converter which was implemented in a 0.8${\mu}$m p-well CMOS process. The proposed digital correction logic is based on optimum multiplexer and two nonoverlapping clock phases resulting in a small die area snd a modular pipelined architecture. The propsoed digital calibration logic which consists of calibration control logic, error averaging logic, and memory can effectively perform self-calibration with little modifying analog functional bolcks of a conventional pipelined A/D conveter.

• Proceedings of the KIEE Conference
• /
• 2006.07d
• /
• pp.2013-2014
• /
• 2006

For large capacity optical CDMA networks, we propose a shared-type encoder/decoder based on an tunable wavelength conveter (TWC) and an arrayed waveguide grating (AWG) router. Feasibility of the structure of the proposed encoder/decoder for dynamic code allocation is tested through simulations using three types of wavelength/time 2-D codes, which are the generalized multi-wavelength prime code(GMWPC), the generalized multi-wavelength Reed-Solomon code(GMWRSC) and the matrix code. Test results show that the proposed encoder/decoder can increase the channel efficiency not only by increasing the number of simultaneous users without any multiple-access interference but by using a relatively short length CDMA codes.

• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.1082-1087
• /
• 2019

In this study, ECG signal amplifier, wireless transmitter/receiver circuit, signal processing filter circuit and A/D converter circuit design required for the development of small sized ECG module for wireless transmission/ reception were performed. In order to verify the performance of ECG sensors, the measurement was performed from 1 m to 3 m to measure the signal noise ratio according to the gateway distance. Experimental results showed that the signal noise ratio at 2 m distance was 17.18 dB on average, which fulfilled the requirements for commercialization. The experimental results obtained in this study are expected to contribute to the low cost, high efficiency mobile health field where remote monitoring diagnosis can be applied to small biometric devices for chronic disease management.

• Proceedings of the KIEE Conference
• /
• 2005.10b
• /
• pp.70-72
• /
• 2005

The present paper designed a weight measuring instrumentation system in which data conversion and a series of signal processing were totally equipped. 16 loadcell are incoming sensors and each output of the loadcell was amplified and filtered for proper analog signal processing. Several measuring instrumentation OP amps and general purposed OP amps were used. 12 bits AID converters converted analog signals to digital bits and a PIC microprocessor controlled the 16 channels of loadcell. RF RS232 modules were used for wireless communication between the PIC microprocessor and an ethernet host for a remote sensor monitoring system development.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.586-589
• /
• 2001

This paper focuses on a method to connect mobile devices such as mobile robot, Automated Guided Vehicle(AGV) to a fieldbus. In this paper, the IEEE 802.11 wireless LAN is used to extend a Profibus-DP network for the mobile devices. In order to integrate these two networks, a protocol converter is developed with two process(i.e., master process of Profibus-DP and virtual master process of IEEE 802.11) and an transmission buffer. Futhermore, a virtual polling algorithm is developed at the protocol conveter in order to satisfy real-time requirements on data communication.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.621-625
• /
• 2007

Oscillating wave amplitude in a bottom-mounted owe chamber designed for wave energy converter is investigated by applying characteristic wave conditions in Korean coastal water. The effects of shape parameters of OWC chamber in a view of wave energy absorbing capability are analyzed. Both experimental and numerical approaches are adopted and their results are compared to optimize the shape parameters which can result in a maximum power production under given wave distribution. The experiment was carried out in a wave flume under 2-D assumption of OWC chamber. In numerical scheme, the potential problem inside the chamber is solved by use of the Green integral equation associated with the Rankine Green function, while outer problem with the Kelvin Green function taking account of fluctuating air pressure in the chamber. Air duct diameter, chamber width, and submerged depths of front skirt and back wall of chamber changes the magnitude and peak frequency of wave absorption significantly.