• Journal of Korea Society of Digital Industry and Information Management
• /
• v.16 no.1
• /
• pp.11-19
• /
• 2020

IoT has been consistently used in various fields such as smart home, wearables, and healthcare. Since IoT devices are small terminals, relatively simple wireless communication protocols such as IEEE 802.15.4 and ISO 18000 series are used. In this paper, we designed the 802.15.4q 2.4 GHz TASK physical layer. Physical protocol data unit of TASK supports bit-level interleaving and shortened BCH encoding. It is spread by unique ternary sequences. There are four spreading factors to choose the data rate according to the communication channel environment. The TASK physical layer was designed using verilog-HDL and verified through the loop-back test of the transceiver. The designed TASK physical layer was implemented in a fpga and tested using MAXIM RFICs. The PER was about 0% at 10 dB SNR. It is expected to be used in small, low power IoT applications.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.1 s.343
• /
• pp.49-56
• /
• 2006

This paper describes the design and the verification of IEEE 802.15.4 LR-WPAN 2.4GHz Physical layer for Ubiquitous Sensor Network(USN). We designed the Carrier Frequency Offset(CFO) compensation satisfied the frequency tolerance of IEEE 802.15.4 LR-WPAN and the adaptive matched filter that re-setting of the threshold for the symbol synchronization of the various USN environment. The multiplications is reduced 1/16 by this method each other at i, q phases and has 0.5dB performance improvement in detection probability. Proposed baseband system is designed with verilog HDL and implemented using FPGA prototype board.

• ETRI Journal
• /
• v.40 no.2
• /
• pp.167-179
• /
• 2018

This paper proposes an IEEE 802.15.4m compliant TV white-space orthogonal frequency-division multiplexing (TVWS)-(OFDM) radio frequency (RF) transceiver that can be adopted in advanced metering infrastructures, universal remote controllers, smart factories, consumer electronics, and other areas. The proposed TVWS-OFDM RF transceiver consists of a receiver, a transmitter, a 25% duty-cycle local oscillator generator, and a delta-sigma fractional-N phase-locked loop. In the TV band from 470 MHz to 698 MHz, the highly linear RF transmitter protects the occupied TV signals, and the high-Q filtering RF receiver is tolerable to in-band interferers as strong as -20 dBm at a 3-MHz offset. The proposed TVWS-OFDM RF transceiver is fabricated using a $0.13-{\mu}m$ CMOS process, and consumes 47 mA in the Tx mode and 35 mA in the Rx mode. The fabricated chip shows a Tx average power of 0 dBm with an error-vector-magnitude of < 3%, and a sensitivity level of -103 dBm with a packet-error-rate of < 3%. Using the implemented TVWS-OFDM modules, a public demonstration of electricity metering was successfully carried out.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.12
• /
• pp.91-96
• /
• 2011

In this paper, a low-power direct-conversion transmitter based on current-mode operation, which satisfies the IEEE 802.15.4 standard, is proposed and implemented in a $0.13{\mu}m$ CMOS technology. The proposed transmitter consists of DACs, LPFs, variable gain I/Q up-conversion mixer, a divide-by-two circuit with LO buffer, and a drive amplifier. By combining DAC, LPF, and variable gain I/Q up-conversion mixer with a simple current mirror configuration, the transmitter's power consumption is reduced and its linearity is improved. The drive amplifier is a cascode amplifier with gain controls and the 2.4GHz I/Q differential LO signals are generated by a divide-by-two current-mode-logic (CML) circuit with an external 4.8GHz input signal. The implemented transmitter has 30dB of gain control range, 0dBm of maximum transmit output power, 33dBc of local oscillator leakage, and 40dBc of the transmit third harmonic component. The transmitter dissipates 10.2mW from a 1.2V supply and the die area of the transmitter is $1.76mm{\times}1.26mm$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.3
• /
• pp.685-690
• /
• 2013

This paper has proposed a multi-channel and wide gain-range baseband circuit blocks for the IEEE 802.15.4g MR-OFDM SUN systems. The proposed baseband circuit blocks consist of two negative-feedback VGAs, an active-RC 5th-order chebyshev low-pass-filter, and a DC-offset cancellation circuit. The proposed baseband circuit blocks provide 1 dB cut-off frequencies of 100 kHz, 200 kHz, 400 kHz, and 600 kHz respectively, and achieve a wide gain-range of +7 dB~+84 dB with 1 dB step. In addition, a DC-offset cancellation circuit has been adopted to mitigate DC-offset problems in direct-conversion receiver. Simulation results show a maximum input differential voltage of $1.5V_{pp}$ and noise figure of 42 dB and 37.6 dB at 5 kHz and 500 kHz, respectively. The proposed I-and Q-path baseband circuits have been implemented in $0.18-{\mu}m$ CMOS technology and consume 17 mW from a 1.8 V supply voltage.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.2A
• /
• pp.176-186
• /
• 2006

In this paper, we propose an enhanced symbol detector algorithm for 2.45GHz LR-WPAN(Low-Rate Wireless Personal Area Network) receiver. Because the frequency offset of $\pm$80ppm on 2.45GHz band is recommended in IEEE 802.15.4 LR-WPAN(Low-Rate Wireless Personal Area Network) specification, a symbol detector algorithm having stable operation in the channel environment with large frequency offset is required. For robustness to the frequency offset, non-coherent detection-based symbol detector algorithm is typically applied in the LR-WPAN receiver modem. However, the noncoherent symbol detector has increased performance degradation and hardware complexity due to squaring loss of I/Q squaring operation. Therefore we propose a coherent detection-based symbol detector algorithm with frequency offset compensation using a preamble symbol. The proposed algorithm is more suitable for LR-WPAN receiver aimed at low-cost, low-power and low-complexity than the non-coherent symbol detector, since it can reduce performance degradation due to squaring loss of I/Q squaring operation and implementation complexity. Simulation results show that the proposed algorithm has performance improvement of about 1dB in various channel environments.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.21 no.3
• /
• pp.27-35
• /
• 2011

Design of Sensor nodes in Wireless Sensor Network(WSN) should be considered some properties as electricity consumption, transmission speed, range, etc., and also be needed the protection against various attacks (e.g., eavesdropping, hacking, leakage of customer's secret data, and denial of services). The stream cipher Rabbit, selected for the final eSTREAM portfolio organized by EU ECRYPT and selected as algorithm in part of ISO/IEC 18033-4 Stream Ciphers on ISO Security Standardization recently, is a high speed stream cipher suitable for WSN. Since the stream cipher Rabbit was evaluated the complexity of side-channel analysis attack as 'Medium' in a theoretical approach, thus the method of power analysis attack to the stream cipher Rabbit and the verification of our method by practical experiments were described in this paper. We implemented the stream cipher Rabbit without countermeasures of power analysis attack on IEEE 802.15.4/ZigBee board with 8-bit RISC AVR microprocessor ATmega128L chip, and performed the experiments of power analysis based on difference of means and template using a Hamming weight model.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.7 s.98
• /
• pp.681-689
• /
• 2005

This paper presents an ultra wide band(UWB) mixer using anti-parallel diode pair(APDP) with simulation and measurement results. The proposed mixer adopts the even-harmonic direct conversion mixing, which consists of a couple of filter, in-phase wilkinson power divider, wideband $45^{\circ}$ power divider, and APDP. The m mixer is operating over 3.1 to 4.8 GHz and producing quadrature(I/Q) outputs with a conversion loss of 18 dB and input third order intercept point($IIP_3$) of 15 dBm. I/Q outputs also have difference of about 0.5 dB and phase difference of ${\times}3^{\circ}$ and $P_{1dB}$ of 2 dBm.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1406-1407
• /
• 2008

In this paper, a micro balanced filter in magnetically coupled LC resonators is proposed, designed, simulated by using FR-4 PCB substrate for low cost, small volume IEEE 802. 11a wireless LAN application. Two pair of coupled LC resonators using magnetic coupling of embedded inductors are applied to obtain bandpass transmission response and improve their phase and magnitude imbalance characteristics. In addition, high dielectric composite film is applied to fabricate the high Q MIM capacitors with small size and high capacitance density. It has an insertion loss of 1.4 dB, a return loss of 10 dB, a phase imbalance of 0.25 degree, and magnitude imbalance of 0.17 dB at frequency bandwidth of 200 MHz ranged from 5.15 GHz to 5.35 GHz, respectively. The proposed balanced filter has a small volume of $1.1mm{\times}1.3mm{\times}0.6mm$ (height).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.12 s.115
• /
• pp.1156-1163
• /
• 2006

This paper presents an ultra wideband(UWB) direct conversion mixer for IEEE 802.15.3a applications with simulation and measurement results. Since the direct conversion mixing causes dc-offset and even-order distortion, the proposed mixer adopts an anti-parallel diode pairs(APDPs) to solve these problems. The proposed mixer consists of an in-phase wilkinson power divider over $3.1{\sim}4.8GHz$, a wideband $45^{\circ}$ power divider over $1.5{\sim}2.4GHz$, and miniatured band pass filters(BPFs) for RF-LO isolations. The conversion loss is optimized with impedance matchings between APDPs and wideband components. The measured mixer shows the conversion loss of 13.5 dB, input third-order intercept-point($IIP_3$) of 7 dBm, and 1-dB gam compression point($P_{1dB}$) of -4 dBm. Quadrature(I/Q) outputs have the magnitude difference of about 1 dB and phase difference of ${\pm}3^{\circ}$.