• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.8 no.1
• /
• pp.1-12
• /
• 1996

In lots of application to heat exchanger systems, closed two-phase thermosyphons are tilted from a horizontal. If the tilt angle, especially, is less than 30$^{\circ}$, the operational performances of thermosyphon are highly dependent on tilt angle. The present study was conducted to better understand such operational behaviors as mech-anni는 of phase change, and flow patterns inside a tilted thermosyphon. For experiment, an ethanol thermosyphon with a 35% of fill charge rate was designed and manufactured, using a copper tube with a diameter 19mm and a length 1500mm. Through a series of test, the tilt angle was kept constant at each of 4 different values in the range 10~25deg. and the heat supply to the evaporator was stepwisely increased up to 30㎾/$m^2$. When a steady state was established to the thermosyphon for each step of thermal loads, the wall temperature distribution and vapor temperature at the condenser were measured. The wall temperature distributions demonstrated a formation of dry patch in the top end zone of the evaporator, with a values of temperature 20~4$0^{\circ}C$ higher than the wetted surface for a moderate heat flux q≒20㎾/$m^2$. Inspite of the presence of hot dry patch, however, the mean values of boiling heat transfer coefficient at the evaporator wall were still in a good agreement with those predicted by Rohsenow's formula, which was based on nucleate boiling. For the condenser, the wall temperatures were practically uniform, and the measured values of condensation heat transfer coefficient were 1.7 times higher than the predicted values obtained from Nusselt's film condensation theory on tilted plate. Using those two expressions, a correlation was formulated as a function of heat flux and tilt angle, to determine the total thermal resistance of a tilted thermosyphon. The correlation formula showed a good agreement with the experimental data within 20%.

• ETRI Journal
• /
• v.39 no.6
• /
• pp.866-873
• /
• 2017

We propose a multilayered-substrate-based power semiconductor discrete device package for a low switching loss and high heat dissipation. To verify the proposed package, cost-effective, low-temperature co-fired ceramic, multilayered substrates are used. A bare die is attached to an embedded cavity of the multilayered substrate. Because the height of the pad on the top plane of the die and the signal line on the substrate are the same, the length of the bond wires can be shortened. A large number of thermal vias with a high thermal conductivity are embedded in the multilayered substrate to increase the heat dissipation rate of the package. The packaged silicon carbide Schottky barrier diode satisfies the reliability testing of a high-temperature storage life and temperature humidity bias. At $175^{\circ}C$, the forward current is 7 A at a forward voltage of 1.13 V, and the reverse leakage current is below 100 lA up to a reverse voltage of 980 V. The measured maximum reverse current ($I_{RM}$), reverse recovery time ($T_{rr}$), and reverse recovery charge ($Q_{rr}$) are 2.4 A, 16.6 ns, and 19.92 nC, respectively, at a reverse voltage of 300 V and di/dt equal to $300A/{\mu}s$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.2
• /
• pp.126-130
• /
• 2008

In this study, in order to develop low loss multilayer piezoelectric actuator, PZN-PZT ceramics were fabricated using $Li_2CO_3,\;Bi_2O_3$, CuO and ZnO as sintering aids, their structural, piezoelectric and dielectric characteristics were investigated according to the amount of ZnO addition, At the sintering temperature of $870^{\circ}C$, the density, electromechanical coupling factor(kp), mechanical quality factor(Qm), dielectric constant(${\epsilon}_r$) and piezoelectric constant($d_{33}$) of 0.4 wt% ZnO added specimen (sintered at $870^{\circ}C$) showed the optimum value of $7.812g/cm^3$, 0.535, 916, 1399, 335 pC/N respectively. Taking into consideration above piezoelectric properties of the specimen sintered at low temperature, it was concluded that PZN-PZT ceramics using 0.4 wt% ZnO as additive showed the optimum characteristics as the composition ceramics for low loss multilayer piezoelectric actuator application.

• The Bulletin of The Korean Astronomical Society
• /
• v.36 no.1
• /
• pp.30.1-30.1
• /
• 2011

2010년 11월 05일부터 11월 29일 중 총 12일간 진천 소재 충북대학교 천문대의 60cm 반사망원경과 ST-8 CCD 카메라를 이용하여 BD And의 BVR CCD 측광 관측을 수행하여 처음으로 BVR 광도 곡선을 완성하였다. 또한, 극심시각 결정을 위한 측광관측이 레몬산 천문대 1m 반사 망원경과 충북대학교 천문대의 35cm 망원경으로 수행되었다. 우리의 관측을 통하여 모두 19개의 극심시각을 새로이 결정하였다. 새로운 관측은 이 별의 공전주기가 이전까지 알려진 0.4629일이 아니라 그 두 배인 0.9258일이며, 기산점도 반주기 바뀌어야 함을 보여준다. BD And의 광도요소를 $MinI=HJD2434962.8602+0.^d9258054E$으로 새롭게 개정하였다. 이 광도요소로 작성한 우리의 BVR 광도곡선은 제1식과 제2식의 깊이가 거의 비슷하며, 식바깥 부분에 잘 발달된 파형 모양을 보인다. 이는 BD And가 짧은 주기의 RS CVn형 식쌍성임을 나타내는 것이다. 우리의 극심시각을 포함한 총 130개의 극심시각에 대한 (O-C)도를 작성한 결과, BD And의 공전주기가 규칙적으로 변화하는 것을 발견하였다. 이 변화를 보이지 않는 제3천체에 의한 광시간 효과로 가정하여, 궤도이심율이 0.78이며, 9.19년의 주기를 가진 광시간 궤도를 결정하였다. 우리의 광도곡선을 2003년 Wilson-Devinney 쌍성 모형으로 분석하여 광도곡선 해를 질량비 q=0.094, 궤도경사각 $i=85.^{\circ}4$, $T_1=6365(K)$, $T_2=6250(K)$, $R_1=1.132(Rsun)$, $R_2=1.304(Rsun)$와 같이 산출하였다. 식바깥에서 나타나는 파형 모양의 변화는 주성의 표면에 매우 큰 흑점으로 잘 설명되며, BVR 광도곡선에서 각전체 광도의 각 8.3%, 10.0%, 11.7%에 해당되는 제3 광도가 검출되었다. 이는 주기연구에서 제안된 제3천체의 존재 가능성을 더 공고히 한다.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2146-2148
• /
• 2005

The 2.5GeV linac of the Pohang Light Source(PLS) is planed to be converted to a XFEL. The PAL XFEL requires a new 1.2-GeV linac that will be combined to the existing linac to increase a beam energy upto 3.7GeV. This stability is mainly determined by a low level RF drive system and klystron-modulators. The stability level of the modulator has to be improved 10 times better to meet the pulse stability of 0.02 %. The regulation methods such as traditional de-Qing and precision inverter charging technology are reviewed to find out suitable upgrade scheme of the modulators. In order to obtain electron beam of the consequently stability for XFEL linac, the pulse-to-pulse beam voltage regulation is less than +/-0.5%. To get the reliable stability of the modulator which is less than +/-0.2%, a charging section is improved in a modulator which has been operated with inverter power supply and de-Q'ing.

• Journal of Microbiology and Biotechnology
• /
• v.23 no.1
• /
• pp.7-14
• /
• 2013

In the Bacillus amyloliquefaciens ${\alpha}$-amylase (BAA), the loop (residues 176-185; region I) that is the part of the calcium-binding site (CaI, II) has two more amino acid residues than the ${\alpha}$-amylase from Bacillus licheniformis (BLA). Arg176 in this region makes an ionic interaction with Glu126 from region II (residues 118-130), but this interaction is lost in BLA owing to substitution of R176Q and E126V. The goal of the present work was to quantitatively estimate the effect of ionic interaction on the overall stability of the enzyme. To clarify the functional and structural significance of the corresponding salt bridge, Glu126 was deleted (${\Delta}$E126) and converted to Val (E126V), Asp (E126D), and Lys (E126K) by site-directed mutagenesis. Kinetic constants, thermodynamic parameters, and structural changes were examined for the wild-type and mutated forms using UV-visible, atomic absoption, and fluorescence emission spectroscopy. Wild-type exhibited higher $k_{cat}$ and $K_m$ but lower catalytic efficiency than the mutant enzymes. A decreased thermostability and an increased flexibility were also found in all of the mutant enzymes when compared with the wild-type. Additionally, the calcium content of the wild-type was more than ${\Delta}E126$. Thus, it may be suggested that ionic interaction could decrease the mobility of the discussed region, prevent the diffusion of cations, and improve the thermostability of the whole enzyme. Based on these observations, the contribution of loop destabilization may be compensated by the formation of a salt bridge that has been used as an evolutionary mechanism or structural adaptation by the mesophilic enzyme.

• Environmental Engineering Research
• /
• v.19 no.3
• /
• pp.247-253
• /
• 2014

The aim of this study was to characterize quintinite in fluoride removal from aqueous solutions, using batch experiments. Experimental results showed that the maximum adsorption capacity of fluoride to quintinite was 7.71 mg/g. The adsorption of fluoride to quintinite was not changed at pH 5-9, but decreased considerably in highly acidic (pH < 3) and alkaline (pH > 11) solution conditions. Kinetic model analysis showed that among the three models (pseudo-first-order, pseudo-second-order, and Elovich), the pseudo-second-order model was the most suitable for describing the kinetic data. From the nonlinear regression analysis, the pseudo-second-order parameter values were determined to be $q_e=0.18mg/g$ and $k_2=28.80g/mg/hr$. Equilibrium isotherm model analysis demonstrated that among the three models (Langmuir, Freundlich, and Redlich-Peterson), both the Freundlich and Redlich-Peterson models were suitable for describing the equilibrium data. The model analysis superimposed the Redlich-Peterson model fit on the Freundlich fit. The Freundlich model parameter values were determined from the nonlinear regression to be $K_F=0.20L/g$ and 1/n=0.51. This study demonstrated that quintinite could be used as an adsorbent for the removal of fluoride from aqueous solutions.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.265-265
• /
• 2007

In the present work, we have studied low temperature sintering and microwave dielectric properties of $ZnAl_2O_4$-zinc borosilicate (ZBS, 65ZnO-$25B_2O_3-10SiO_2$) glass composites. The focus of this paper was on the improvement of sinterability, low dielectric constant, and on the theoretical proof regarding of microwave dielectric properties in $ZnAl_2O_4$-ZBS glass composites, respectively. The $ZnAl_2O_4$ with 60 vo1% ZBS glass ensured successful sintering below $900^{\circ}C$. It is considered that the non-reactive liquid phase sintering (NPLS) occurred. In addition, $ZnAl_2O_4$ was observed in the $ZnAl_2O_4$-(x)ZBS composites, indicating that there were no reactions between $ZnAl_2O_4$ and ZBS glass. $ZnB_2O_4\;and\;Zn_2SiO_4$ with the willemite structure as the secondary phase was observed in the all $ZnAl_2O_4$-(x)ZBScomposites. In terms of dielectric properties, the application of the $ZnAl_2O_4$-(x)ZBS composites sintered at $900^{\circ}C$ to LTCC substrate were shown to be appropriate; $ZnAl_2O_4$-60ZBS (${\varepsilon}_r$= 6.7, $Q{\times}f$ value= 13,000 GHz, ${\tau}_f$= -30 ppm/$^{\circ}C$). Also, in this work was possible theoretical proof regarding of microwave dielectric properties in $ZnAl_2O_4$-(x)ZBS composites.

• Journal of Microbiology
• /
• v.35 no.3
• /
• pp.165-171
• /
• 1997

A sulfer-oxidizing bacterium was isolated from mine wastewater and characterized. The isolate was gra-negative, rod (0.2 * 1.2-1.5.mu.m), nonmotiloe, catalase positive, and oxidase prositive. The opotimal pH and temperature for growth were 7.0 and 30.deg.C. respectively. The optimum thiosulfate concentration was 70 mM and the maximum growth rate was 0.081 hr. The major ubiquinone contained in the isolate was Q-8. The cellular fatty acid composition was $C_{16 : 0}$, $C_{18 : 1}$, $C_{17cyc}$,and $C_{19cyc}$ as nonpolar fatty acids, and 3-OH C10 : 0 and 3-OH $C_{12 : 0}$ as hydroxylated fatty acids. The isolate was a facultative chemolithoautotroph which can grow autotrophically on sodium thiosulfate and sodium sulfide and which can grow heterotrophically on yeast extract. It can also grow mixotrophically on sodium thiosulfate and yeast extract. Comparison of the 16S rRNA gene sequence of the isolate with that of Thiobacillus species and Paracoccus thiocyanatus revealed that it is closely related to T. caldus which belongs to the .betha.-subclass of the class Proteobacteria. However, the isolated could not grow at extremely low pH (pH 1-3.5). On the basis of the phenotypic, chemotaxonomic and phylogenetic data, the isolate was tentatively named Thiobacillus sp. strain C.ain C.

• Parasites, Hosts and Diseases
• /
• v.53 no.2
• /
• pp.163-167
• /
• 2015

This study aimed to determine the seroprevalence and to identify risk factors associated with Neospora spp. infection in horses in Jordan. Management related data were collected from each farm and individual horses. Sera from 227 horses from 5 of 6 climatic regions in Jordan were analyzed for the presence of antibodies to Neospora spp. by ELISA kit. The study was performed during spring of 2010. The association between seropositivity and risk factors was analyzed. A total of 7 (3%) of 227 sera had antibodies for Neospora spp. There was a significant regional difference (P=0.018) between the 5 climatic regions. Positive cases were located in Amman and Irbid, while the other regions (Zarqa, Jordan Valley, and Wadi Mousa) had zero prevalence. The use of anthelmintics at least once a year resulted in a significant reduction of the seroprevalence to Neospora spp. (1.6% vs 9.8%). However, this might be a phenomenon by chance and a better hygiene since owners can invest in anthelmintics. Other risk factors such as age, gender, breed, usage, body condition score, grazing, presence of other animals mixed with the horses in the same property, and a history of previous diseases were not significantly associated with the seroprevalence to Neospora spp. infection. This is the first study to report on the presence of Neospora seropositive horses in Jordan. Further studies are warranted to better understand the role of certain risk factors in the transmission of Neospora spp. among horse population and to determine which Neospora spp. are responsible for the infection.