• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.6
• /
• pp.895-901
• /
• 1986

This paper presents direct adaptive controllers for single-input single-output nonminimum phase systems based on PID structures. Also, characteristics of these schemes are compared, and convergence properties are considered. In these schemes, controller parameters are estimated from the least-square algorithm and some additional auxiliary parameters are obtained from the proposed polynomial identity which is derived from the pole placement equation and the Bezout identity. The effectiveness of these schemes is demonstrated by computer simulation that has been carried out for a very difficult example.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.8
• /
• pp.759-763
• /
• 2009

The goal of this study is to examine the effect of the number of slots on the noise from BLDC motors. To this end, the number of poles was fixed to 4 and the number of the slots was set to 6 or 24 before noise was measured. Motors having different numbers of slots showed clear differences in noise. Cogging torque, torque ripple and normal local force were interpreted, analyzed and compared to determine the reason for the differences. To determine the cause of the noise, cogging torque, torque ripple and normal local force were calculated, which are representative noise sources of BLDC motors, and FFT was performed to analyze their frequency components(harmonics). The results show that torque ripple and normal local force were the dominant factors in the noise difference between the 6-slot and 24-pole motors. As the number of the slots increased, the number of harmonics decreased and their amplitude of harmonic were reduced, which was attributed as the reason for the noise differences.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.6
• /
• pp.328-333
• /
• 2015

Squirrel cage induction motors have mostly been used for their small capacity because the starting torque is smaller than the starting current during start-up. However, as more and more mid-to-large capacity motors are developed, the demands for improvements in performance characteristics have also increased. In this study, the starting characteristics of squirrel cage induction motors were analyzed based on the rotor materials and shapes using a finite element method to provide design data suitable for different use purposes and capacities. We further completed analysis by combining electromagnetic equations deduced from Maxwell’s equations and the circuit equations of stators and rotors. A moving coordinator was introduced to rotate the rotor during the analysis, and the torques calculated via the finite element method were combined with the motion equations to calculate the position and angular velocity of the rotors at the next time, thereby analyzing the transient characteristics. The analysis results of the transient characteristics were applied to a 3-phase 4-pole 5-hp induction motor to calculate the starting torque, speed, and rotation angle of the rotors. In the reference model, the materials and shapes of the rotor slot were changed to copper and silicon copper and a deep slot, shallow slot, and long-neck-shaped slot.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.5
• /
• pp.451-458
• /
• 2002

Absorptive type SP3T(Single Pole Three Throw) and SP8T switch modules over the 6-18 GHz are designed and fabricated. The epitaxial structure of GaAs PIN diode for switch modules are designed for low loss and high power capability. The maximum input power of SP3T and SP8T switch modules are 2 W and 1 W, respectively. The switching time with driver circuit is less than 130 nsec. The maximum insertion loss of SP3T switch module and SP8T module shows 2.8 dB and 4.2 dB, respectively. The isolation between input port and output port is more than 55 dB. Two switch modules for electronic warfare system have passed the environment tests of the related test items.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.2
• /
• pp.92-100
• /
• 2010

A new class of electronically commutated brushless motor, the flux-switching motor(FSM) is gradually emerging in power tools and household appliances especially fan and pump application because of green policy. This motor offers advantages of high-power density and relatively high efficiency compare with induction motor, low cost and simple motor structure compare with bldc motor. This paper presents the principle of the FSM and design of the 12/6 pole FSM drive system for fan application. Finally, test results of the prototype motor are provided to verify a validity of the fan application with TMS320F2812 DSP and inverter.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.6
• /
• pp.2284-2291
• /
• 2018

This paper deals with optimum design of surface mounted permanent magnet synchronous motor (SPMSM) for automotive component. For a compact system structure, it was designed as a motor with a 14-pole 12-slot concentrated winding and hollow shaft. The motor is a thin type structure which stator outer diameter is relatively large compared to its axial length and is designed to have a high magnetic saturation for increasing the torque density. Since the high magnetic saturation in the stator core increases the axial leakage flux, a 3-dimensional (3-D) finite element analysis (FEA) is indispensable for torque analysis. However, optimum designs using 3-D FEA is inefficient in terms of time and cost. Therefore, equivalent 2-D FEA which is able to consider axial leakage flux is applied to the optimization to overcome the disadvantages of 3-D FEA. The structure for cost reduction is proposed and optimum design using equivalent 2-D FEA has been performed.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.6
• /
• pp.2187-2195
• /
• 2018

In order to realize the multi-objective control of single-input multi-output nonlinear differential algebraic system (NDAS) and to improve the dynamic characteristics and static accuracy, a design method of nonlinear control with multi-objective feedback (NCMOF) is proposed, the principium of this method to arrange system poles, as well as its nature to coordinate dynamic characteristics and static accuracy of the system are analyzed in detail. Through NCMOF design method, the multi-objective control of the system is transformed into linear space, and then it is effectively controlled under the nonlinear feedback control law, the problem to balance all control objectives caused by less input and more output of the system thus is solved. Applying NCMOF design method to generator excitation system, the nonlinear excitation control law with terminal voltage, active power and rotor speed as objective outputs is designed. Simulation results show that NCMOF can not only improve the dynamic characteristics of generator, but also damp the mechanical oscillation of a generator in transient process. Moreover, NCMOF can control the terminal voltage of the generator to the setting value with no static error under typical disturbances.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.6
• /
• pp.1935-1943
• /
• 2014

In recent years, the induction machines are increasingly being used as self-excited induction generators (SEIG). This generator is especially widely employed for small-scale power plants driven by renewable energy sources. The application of power electronic components in the induction generator control (IGC) and the loading of SEIG using nonlinear loads will generate harmonic currents. This paper analyzes the propogation of harmonic currents on the SEIG with nonlinear loads. Transfer function method in the frequency domain is used to calculate the gain and phase angle of each harmonic current component which are generated by a nonlinear loads. Through the superposition approach, this method has also been used to analyze the propagation of harmonic currents from nonlinear load to the stator windings. The simulation for the propagation of harmonic currents for a 4 pole, 1.5 kW, 50Hz, 3.5A, Y-connected, rotor-cage SEIG with energy-saving lamps, have provided results almost the same with the experiment. It can prove that the validity of the proposed models and methods. The study results showed that the propagation of harmonic currents on the stator windings rejects high order harmonics and attenuates low order harmonics, consequently THDI diminish significantly on the stator windings.

• Korean Journal of Human Ecology
• /
• v.22 no.6
• /
• pp.649-658
• /
• 2013

Various paper ornaments appear in Gut, the rite of shaman in Jeju, and these are frequently called Gime, Gimekijeon or Gimejeonji. Gime are slips of white or colored paper, made to resemble the shape of god and used in the ritual shaman dances of Jeju. These Gime are hung around an altar, fastened to the end of a green bamboo pole, or held in the shaman's hands when they dance. The purpose of the study is to develop textile design based on the formative features of Gime, as a way of using Myth of shaman in Jeju. This study is used Gime made by 'Kim Yoon-Su' Simbang (shaman) who plays a role of Intangible Cultural Assets of The 71th 'Jeju Chilmeoridang Yeongdeunggut'. As a result, it was to develop the Komusaljang pattern, Seongjukkot pattern, Jijeon pattern, Jowoangki pattern and Cheoljjukdae pattern design of Jeju image using Gime that is one of the unique, indigenous pattern of Jeju.

• Journal of Powder Materials
• /
• v.18 no.6
• /
• pp.482-487
• /
• 2011

Alloy 617, Ni-22Cr-12Co-9Mo base oxide dispersion strengthened alloy was fabricated by using mechanical alloying, hot isostatic pressing and hot rolling. Uniaxial tensile tests were performed at room temperature and at $700^{\circ}C$. Compared with the conventional Alloy 617, ODS alloy showed much higher yield strength and tensile strength, but lower elongation. Fracture surfaces of the tensile tested specimens were investigated in order to find out the mechanism of fracture mode at each test temperature. Grain adjustment during tensile deformation was analyzed by electron backscattered diffraction mapping, inverse pole figures and TEM observation.