• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2019.05a
• /
• pp.98-100
• /
• 2019

In the past, there were several researchers investigating waves generated by a small boat. Wave generated by a ship can be divided into two distinct systems of waves, such as transverse and diverging waves. It is necessary to understand the behavior of a ship in waves generated by a small boat near port in the view point of ship safety. In this study, the motion of moored floater in waves generated by a small boat near port is investigated. The model test is performed in waves in a square tank in Changwon National University (CWNU). IMU and optical-based system which uses the technique of recording and capturing attitude with respect time are used for measuring 6DOF motion of the moored floater. In addition, tension gauges are used to measure the tension of mooring lines. The effect of waves generated by a small boat on motion of the moored floater near port is investigated through performing the model test in various wave directions of virtually but reasonably assumed wave scenarios.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.6
• /
• pp.66-71
• /
• 2007

Development of a locomotive mechanism for the capsule type endoscopes will largely enhance their ability to diagnose disease of digestive organs. As a part of it, there should be provided a detection device of their position in human organs for the purpose of observation and motion control. In this paper, a permanent magnet outside human body was employed to project magnetic field on a capsule type endoscope, while its position dependent flux density was measured by three hall-effect sensors which were orthogonally installed inside the capsule. In order to detect the 2-D position data of the capsule with three hall-effect sensors including the roll, pitch and yaw angle, the permanent magnet was extra translated during the measurement. In this way, the 2-D coordinates and three rotation angles of a capsule endoscope on the same motion plane with the permanent magnet could be detected. The working principle and performance test results of the capsule position detection device were introduced in this paper showing that they could be also applied to 6-DOF position detection.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.1
• /
• pp.105-112
• /
• 2013

This paper presents the structural design and finite element analysis of precision stage based on a double triangular parallel mechanism for precision positioning and large force generation. Recently, with the acceleration of miniaturization in mobile appliances, the demand for precision aligning and bonding has been increasing. Such processes require both high precision and large force generation, which are difficult to obtain simultaneously. This study aimed at constructing a precision stage that has high precision, long stroke, and large force generation. Actuators were tactically placed and flexure hinges were carefully designed by optimization process to constitute a parallel mechanism with a double triangular configuration. The three actuators in the inner triangle function as an in-plane positioner, whereas the three actuators in the outer triangle as an out-of-plane positioner. Finite element analysis is performed to validate load carrying performances of the developed precision stage.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2014.10a
• /
• pp.219-221
• /
• 2014

The objective of this paper is to simulate the dynamic behavior of a floating structure model, using image processing and close-range photogrammetry, instead of the contact sensors. Previously, the movement of structure was presented through the exterior orientation estimation of a single camera by space resection. The inverse resection yields the 6 orientation parameters of the floating structure, with respect to the camera coordinate system. The single camera solution is of interest in applications characterized by restriction in term of costs, unfavorable observation conditions, or synchronization demands when using multiple cameras. This article discusses the theoretical determinations of camera exterior orientation based on Direct Linear Transformation and photogrammetric resection using least squares adjustment. The proposed method was used to monitor the motion of a floating model. The results of six degrees of freedom (6-DOF) by inverse resection show that the appropriate initial values by DLT can be effectually applied in least squares adjustment, to obtain the precision of exterior orientation parameters. Additionally, a comparison between the close-range photogrammetry and total station results was feasibly verified. Therefore, the proposed method can be considered as an efficient solution to simulating the movement of floating structure.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10a
• /
• pp.223-226
• /
• 1996

The moving vehicle with disturbances has the 6 dof motion in the pitching, yawing and rolling directions of two independent axes. The control system in such a moving vehicle has to perform disturbance rejection well. The paper presents PID controller with disturbance rejection function, low sensitivity filter and notch the bending frequency rejection. The performance of a designed system has been certified by the simulation and experiment results.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.135-140
• /
• 1992

This paper presents the configuration, HILS procedure and performance simulation results of the RPV autopilot including a strapdown AHRS. Real time hardware-in-the-loop simulation was performed by using a 3 axis flight motion simulator alonged assumed flight trajectory of the RPV. Being compared with the result of the 6 DOF simulation, the HILS results showed that the performance of the autopilot was satisfactory.

• Journal of Ocean Engineering and Technology
• /
• v.29 no.6
• /
• pp.436-444
• /
• 2015

A submerged body is sensitive to changes in the roll moment because of the small restoring moment and moment of inertia. Thus, a method for predicting the roll-related hydrodynamic coefficients is important. This paper describes a deduction method for the hydrodynamic coefficients based on the results of a coning motion test. A resistance test, static drift test, and coning motion test were performed to obtain the coefficients in the towing tank of Seoul National University. The sum of the hydrodynamic force, inertial force, gravity, and buoyancy was measured in the coning motion test. The hydrodynamic force was deduced by subtracting the inertial force, gravity, and buoyancy from the measured force. The hydrodynamic coefficients were deduced using the regression method.

• The korean journal of orthodontics
• /
• v.43 no.1
• /
• pp.42-52
• /
• 2013

The aim of this paper was to propose a new method of bimaxillary orthognathic surgery planning and model surgery based on the concept of 6 degrees of freedom (DOF). A 22-year-old man with Class III malocclusion was referred to our clinic with complaints of facial deformity and chewing difficulty. To correct a prognathic mandible, facial asymmetry, flat occlusal plane angle, labioversion of the maxillary central incisors, and concavity of the facial profile, bimaxillary orthognathic surgery was planned. After preoperative orthodontic treatment, surgical planning based on the concept of 6 DOF was performed on a surgical treatment objective drawing, and a Jeon's model surgery chart (JMSC) was prepared. Model surgery was performed with Jeon's orthognathic surgery simulator (JOSS) using the JMSC, and an interim wafer was fabricated. Le Fort I osteotomy, bilateral sagittal split ramus osteotomy, and malar augmentation were performed. The patient received lateral cephalometric and posteroanterior cephalometric analysis in postretention for 1 year. The follow-up results were determined to be satisfactory, and skeletal relapse did not occur after 1.5 years of surgery. When maxillary and mandibular models are considered as rigid bodies, and their state of motion is described in a quantitative manner based on 6 DOF, sharing of exact information on locational movement in 3-dimensional space is possible. The use of JMSC and JOSS will actualize accurate communication and performance of model surgery among clinicians based on objective measurements.

• International Journal of Aeronautical and Space Sciences
• /
• v.6 no.2
• /
• pp.23-32
• /
• 2005

An experimental control system is proposed for the attitude control of a simplified 2-DOF helicopter model. The main rotor is a rigid one, and the fuselage is simply supported by a fixed hinge point where the longitudinal motion is decoupled from the lateral one since the translations and the rolling rotation are completely removed. The yaw trim of the helicopter is performed with a tail rotor, by which the azimuthal attitude can be adjusted on the rotatable post in the yaw direction. The robust sliding mode control tracking a given attitude angle is proposed based on the flight dynamics. A pitch damper is inserted for the control of pitching angle while the compensator to reaction torque is used for the control of azimuth angle. Several parameters of the system are selected through experiments. The results shows that the proposed control method effectively counteracts nonlinear perturbations such as main rotor disturbance, undesirable chattering, and high frequency dynamics.

• Structural Engineering and Mechanics
• /
• v.86 no.6
• /
• pp.765-778
• /
• 2023

This study investigates the free vibration and buckling analyses of isotropic curved plate structures fixed at all ends. The Kirchhoff-Love Plate Theory (KLPT) and Finite Element Method (FEM) are employed to model the curved structure. In order to perform the finite element analysis, a four-node quadrilateral element with 5 degrees of freedom (DOF) at each node is utilized. Additionally, the drilling effect (θ_z) is considered as minimal to satisfy the DOF of the structure. Lagrange's equation of motion is used in order to obtain the first ten natural frequencies and the critical buckling values of the structure. The effects of various radii of curvatures and aspect ratio on the natural frequency and critical buckling load values for the single-bay and two-bay curved frames are investigated within this scope. A computer code based on finite element analysis is developed to perform free vibration and buckling analysis of curved plate frames. The natural frequency and critical buckling load values of the present study are compared with ANSYS R18.2 results. It has been concluded that the results of the present study are in good agreement with ANSYS results for different radii of curvatures and aspect ratio values of both single-bay and two-bay structures.