• International Journal of Aeronautical and Space Sciences
• /
• 제18권3호
• /
• pp.414-424
• /
• 2017

This paper introduces an experimental device which can measure accurate aerodynamic forces without support interference in wide experimental region for wind tunnel test of micro aerial vehicles (MAVs). A stereo pattern recognition (SPR) method was introduced to a magnetic suspension and balance system (MSBS), which can eliminate support interference by levitating the experimental model, to establish wider experimental region; thereby MSBS-SPR integrated system was developed. The SPR method is non-contact, highly accurate three-dimensional position measurement method providing wide measurement range. To evaluate the system performance, a series of performance evaluations including SPR system measurement accuracy and 6 degrees of freedom (DOFs) position/attitude control of the MAV model were conducted. This newly developed system could control the MAV model rapidly and accurately within almost 60mm for translational DOFs and 40deg for rotational DOFs inside of $300{\times}300mm$ test section. In addition, a static wind tunnel test was conducted to verify the aerodynamic force measurement capability. It turned out that this system could accurately measure the aerodynamic forces in low Reynolds number, even for the weak forces which were hard to measure using typical balance system, without making any mechanical contact with the MAV model.

• 한국해양공학회지
• /
• 제25권6호
• /
• pp.116-122
• /
• 2011

A realtime simulator using an explicit integration method is introduced to improve the solving performance for the dynamic analysis of a wheeled vehicle. Because a full vehicle system has many parts, the development of a numerical technique for multiple d.o.f. and ground contacts has been required to achieve a realtime dynamics analysis. This study proposes an efficient realtime solving technique that considers the wheeled vehicle dynamics behavior with full degrees of freedom and wheel contact with soft ground such as sand or undersea ground. A combat vehicle was developed to verify this method, and its dynamics results are compared with commercial programs using implicit integration methods. The combat vehicle consists of a chassis, double wishbone type front and rear suspension, and drive train. Some cases of vehicle dynamics analysis are carried out to verify the realtime ratio.

• 한국지진공학회논문집
• /
• 제6권5호
• /
• pp.37-43
• /
• 2002

복합구조제어시스템의 동시최적설계방법에 관하여 연구하였다. 여기에서는 수동제어장치 뿐만 아니라 능동제어장치의 배치와 용량, 제어기 등이 설계변수가 되며 설계인자들의 만족도를 나타내는 선호도함수를 정의하여 이를 이용하여 최적화문제를 정식화한다. 또한 수동 및 능동제어장치의 설계변수로부터 동시에 최적해를 찾아내기 의한 수치적 방법으로 유전자알고리즘을 사용하였다. 지진하중을 받는 다자유도 구조물의 설계에 및 수치모사를 통하여 제안한 방법의 타당성을 검증하고자 하였다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제6권2호
• /
• pp.347-360
• /
• 2014

The auto-berthing of a ship requires excellent control for safe accomplishment. Crabbing, which is the pure sway motion of a ship without surge velocity, can be used for this purpose. Crabbing is induced by a peculiar operation procedure known as the push-pull mode. When a ship is in the push-pull mode, an interacting force is induced by complex turbulent flow around the ship generated by the propellers and side thrusters. In this paper, three degrees of freedom equations of the motions of crabbing are derived. The equations are used to apply the adaptive backstepping control method to the auto-berthing controller of a cruise ship. The controller is capable of handling the system non-linearity and uncertainty of the berthing process. A control allocation algorithm for a ship equipped with two propellers and two side thrusters is also developed, the performance of which is validated by simulation of auto-berthing.

• International Journal of Automotive Technology
• /
• 제7권6호
• /
• pp.749-756
• /
• 2006

This paper presents a complex stochastic wheelbase preview control method of a motorcycle suspension based on hierarchical modeling method. As usual, a vehicle suspension system is controlled as a whole body. In this method, a motorcycle suspension with five Degrees of Freedom(DOF) is dealt with two local independent 2-DOF suspensions according to the hierarchical modeling method. The central dynamic equations that harmonize local relations are deduced. The vertical and pitch accelerations of the suspension center are treated as center control objects, and two local semi-active control forces can be obtained. In example, a real time Linear Quadratic Gaussian(LQG) algorithm is adopted for the front suspension and the combination of the wheelbase preview and LQG control method is designed for the rear suspension. The results of simulation show that the control strategy has less calculating time and is convenient to adopt different control strategies for front and rear suspensions. The method proposed in this paper provides a new way for the vibration control of multi-wheel vehicles.

• Advances in robotics research
• /
• 제2권1호
• /
• pp.99-112
• /
• 2018

The main contribution of this work is the design of a field programmable gate array (FPGA) based ARX-Laguerre proportional-integral observation (PIO) system for fault detection and identification (FDI) in a multi-input, multi-output (MIMO) nonlinear uncertain dynamical robot manipulators. An ARX-Laguerre method was used in this study to dynamic modeling the robot manipulator in the presence of uncertainty and disturbance. To address the challenges of robustness, fault detection, isolation, and estimation the proposed FPGA-based PI observer was applied to the ARX-Laguerre robot model. The effectiveness and accuracy of FPGA based ARX-Laguerre PIO was tested by first three degrees of the freedom PUMA robot manipulator, yielding 6.3%, 10.73%, and 4.23%, average performance improvement for three types of faults (e.g., actuator fault, sensor faults, and composite fault), respectively.

• International journal of advanced smart convergence
• /
• 제4권2호
• /
• pp.163-169
• /
• 2015

This study proposes a sports simulation device with various harmonics generation. The proposed system is composed of 6 degrees of freedom simulator devices and three types of sports simulation such as walking, snowboard, and jet-ski. In this research, every joint movement is designed with a crank-and-slider mechanism, which is efficient for generating continuous curvature smoothly. Contrary to the conventional spatial simulator with linear actuators, harmonics generation and its spatial combinations become the crucial issue in this research. The harmonic pattern in each joint is modelled for generating smooth curvatures that are also superposed for achieving overall motions. In addition, the targeted motions of sports simulations have different physical factors of periodic gait motion, frictionless surface, and buoyant effects, which are respectively designed by integrating three dimensional graphics information.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권6호
• /
• pp.906-915
• /
• 2004

In this paper, we address the development of magnetic levitation positioning system. This planar magnetic levitator employs four permanent magnet liner motors. Each motor generates vertical force for suspension against gravity, as well as horizontal force for driving levitation object called a platen. This stage can generate six degrees of freedom motion by the vertical and horizontal force. We derived the mechanical dynamics equation using Lagrangian method and used coenergy to express an electromagnetic force. We proposed a control algorithm for the position and posture control from its initial value to its desired value using sliding mode control. Some simulation results are provided to verify the effectiveness of the proposed control scheme.

• Coupled systems mechanics
• /
• 제7권6호
• /
• pp.649-668
• /
• 2018

In this paper, we present a numerical model for fluid-structure interaction between structure built of porous media and acoustic fluid, which provides both pore pressure inside porous media and hydrodynamic pressures and hydrodynamic forces exerted on the upstream face of the structure in an unified manner and simplifies fluid-structure interaction problems. The first original feature of the proposed model concerns the structure built of saturated porous medium whose response is obtained with coupled discrete beam lattice model, which is based on Voronoi cell representation with cohesive links as linear elastic Timoshenko beam finite elements. The motion of the pore fluid is governed by Darcy's law, and the coupling between the solid phase and the pore fluid is introduced in the model through Biot's porous media theory. The pore pressure field is discretized with CST (Constant Strain Triangle) finite elements, which coincide with Delaunay triangles. By exploiting Hammer quadrature rule for numerical integration on CST elements, and duality property between Voronoi diagram and Delaunay triangulation, the numerical implementation of the coupling results with an additional pore pressure degree of freedom placed at each node of a Timoshenko beam finite element. The second original point of the model concerns the motion of the outside fluid which is modeled with mixed displacement/pressure based formulation. The chosen finite element representations of the structure response and the outside fluid motion ensures for the structure and fluid finite elements to be connected directly at the common nodes at the fluid-structure interface, because they share both the displacement and the pressure degrees of freedom. Numerical simulations presented in this paper show an excellent agreement between the numerically obtained results and the analytical solutions.

• 수산해양기술연구
• /
• 제43권1호
• /
• pp.49-61
• /
• 2007

Otter boards in the trawl are the one of essential equipments for the net mouth to be spread to the horizontal direction. Its performance should be considered in the light of the spreading force to the drag and the stability of towing in the water. Up to the present, studies of the otter boards have focused mainly on the drag and lift force, but not on the stability of otter boards movement in 3 dimensional space. In this study, the otter board is regarded as a rigid body, which has six degrees of freedom motion in three dimensional coordinate system. The forces acting on the otter boards are the underwater weight, the resistance of drag and spread forces and the tension on the warps and otter pendants. The equations of forces were derived and substituted into the governing equations of 6 degrees of freedom motion, then the second order of differential equations to the otter boards were established. For the stable numerical integration of this system, Backward Euler one of implicit methods was used. From the results of the numerical calculation, graphic simulation was carried out. The simulations were conducted for 3 types of otter boards having same area with different aspect ratio(${\lambda}=0.5,\;1.0,\;1.5$). The tested gear was mid-water trawl and the towing speed was 4k't. The length of warp was 350m and all conditions were same to each otter board. The results of this study are like this; First, the otter boards of ${\lambda}=1.0$ showed the longest spread distance, and the ${\lambda}=0.5$ showed the shorted spread distance. Second, the otter boards of ${\lambda}=1.0$ and 1.5 showed the upright at the towing speed of 4k't, but the one of ${\lambda}=0.5$ heeled outside. Third, the yawing angles of three otter boards were similar after 100 seconds with the small oscillation. Fourth, it was revealed that the net height and width are affected by the characteristics of otter boards such as the lift coefficient.