• 한국정보처리학회:학술대회논문집
• /
• 한국정보처리학회 2021년도 추계학술발표대회
• /
• pp.409-412
• /
• 2021

본 논문에서는 카페나 패스트푸드점같은 장소에서 인간을 대신하여 임의의 위치에 있는 다양한 컵을 3D 카메라로 검출하여 알맞은 위치로 분리수거하는 6축 수직 다관절 로봇 팔을 설계하였다. Yaw-Pitch-Pitch-Pitch-Yaw-Yaw 6축 구조로 설계하였으며, 이를 구동하기 위한 관절 구동기의 용량을 분석을 통해 최적화하였다. 각각 재질이 다른 컵을 그리퍼를 이용하여 잘 파지할 수 있도록 재질에 따른 파지력을 분석하였고 압력센서를 이용하여 재질이 다른 컵을 구분하여 분리수거 할 수 있도록 하였다. 실험을 통해 로봇의 성능과 개선점을 제시하였다.

• 한국기계가공학회지
• /
• 제20권4호
• /
• pp.16-23
• /
• 2021

Currently, 6-axis articulated robots are used throughout the industry because of their 6-dof (degrees of freedom) and usability. However, 6-axis articulated robots have a fixed base and their movements are limited by the rotational operating range of each axis. If the angle of the 2-axis additional axes can be adjusted according to the position and orientation of the end-effector of the 6-axis articulated robot, the effectiveness of the 6-axis articulated robot can be further increased in areas where the angle is important, such as welding. Therefore, in this paper, we proposed a cooperative kinematic inter-operation strategy. The strategy will be verified using the Simulink of MATLABⓇ, an engineering program, and RecurdynⓇ, a dynamic simulation program.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.395-396
• /
• 2013

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1992년도 춘계학술대회 논문집
• /
• pp.349-353
• /
• 1992

로봇 경로프로그래밍 작업의 단순화는 산업용 로봇응용분야중 경로가 복잡할 경우, 예를 들어 연삭, 디버링, 폴리싱등 의 가공분야 그리고 아크용접같은 작업에서, 더욱 절실한 문제가 되고있다. 기존 로봇 프로그래밍 방식은 죠이스틱 또는 티칭 유니트, 오프라인 그리고 메스터-슬레이브 방식으로 구분될 수 있는데 각각 많은 프로그래밍 시간소요, 현장성부족 그리고 적용 로봇에의 한계를 문제점으로 들 수 있다. 여기서는 6축 수직 다관절 로봇의 손목부위에 6자 유도의 F/T 센서를 부착하여 작업자가 직접 로봇의 엔드 이펙트를 잡고 원하는 경로를 따라가는 동안 경로가 자동 프로 그래밍되는 알고리즘을 실험 결과와 함께 제시하고 있다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 추계학술대회 논문집
• /
• pp.339-340
• /
• 2009

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 춘계학술대회 논문집
• /
• pp.269-270
• /
• 2012

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 춘계학술대회 논문집
• /
• pp.267-268
• /
• 2012

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.393-394
• /
• 2013

• 한국기계가공학회지
• /
• 제16권4호
• /
• pp.113-118
• /
• 2017

As the demand for industrial robots and Automated Guided Vehicles (AGVs) increases, higher performance is also required from them. Fuzzy controllers, as part of an intelligent control system, are a direct control method that leverages human knowledge and experience to easily control highly nonlinear, uncertain, and complex systems. This paper uses a $LabVIEW^{(R)}-based$ fuzzy controller with gain scheduling to demonstrate better performance than one could obtain with a fuzzy controller alone. First, the work area was set based on forward kinematics and inverse kinematics programs. Next, $LabVIEW^{(R)}$ was used to configure the fuzzy controller and perform the gain scheduling. Finally, the proposed fuzzy gain scheduling controller was compared with to controllers without gain scheduling.

• 한국생산제조학회지
• /
• 제22권2호
• /
• pp.318-323
• /
• 2013

For fast and accurate motion of 6-axis articulated robot, more noble motion control strategy is needed. In general, the movement strategy of industrial robots can be divided into two kinds, PTP (Point to Point) and CP (Continuous Path). Recently, industrial robots which should be co-worked with machine tools are increasingly needed for performing various jobs, as well as simple handling or welding. Therefore, in order to cope with high-speed handling of the cooperation of industrial robots with machine tools or other devices, CP should be implemented so as to reduce vibration and noise, as well as decreasing operation time. This paper will realize CP motion (especially joint-linear) blending in 3-dimensional space for a 6-axis articulated (lab-manufactured) robot (called as "RS2") by using LabVIEW$^{(R)}$ (6) programming, based on a parametric interpolation. Another small contribution of this paper is the proposal of motion blending simulation technique based on Recurdyn$^{(R)}$ V7 and Solidworks$^{(R)}$, in order to figure out whether the joint-linear blending motion can generate the stable motion of robot in the sense of velocity magnitude at the end-effector of robot or not. In order to evaluate the performance of joint-linear motion blending, simple PTP (i.e., linear-linear) is also physically implemented on RS2. The implementation results of joint-linear motion blending and PTP are compared in terms of vibration magnitude and travel time by using the vibration testing equipment of Medallion of Zonic$^{(R)}$. It can be confirmed verified that the vibration peak of joint-linear motion blending has been reduced to 1/10, compared to that of PTP.