• 수산해양기술연구
• /
• 제49권4호
• /
• pp.500-504
• /
• 2013

A total of 24 juvenile specimens of Thunnus tonggol (5.45~7.26mm in total length) of the Sombridae were collected from the southeast sea of Jeju Island during 26~30 July, 2013. Twenty-four specimens identified T. tonggol have melanophores distributed on the 1st dorsal-fin rays, the dorsal of head and vetral side. Three individulas were identified using mitochondrial DNA cytochrome oxidase submit 1 (CO1) sequences (452 base pairs). All were identified as T. tonggol, their mtCO1 sequences being consistent with those of Thunnus tonggol (d=0.000), followed by Thunnus albacares (d=0.002) and Thunnus obesus (d=0.007).

• 한국농공학회논문집
• /
• 제46권5호
• /
• pp.141-153
• /
• 2004

Wetland system is widely accepted as one of natural water purification systems around the world for nonpoint sources pollution control. Constructed wetlands have become a popular technology for treating contaminated surface and waste water. In this study, the field experiment to reduce nonpoint source pollution loadings from polluted stream waters using wetland system was performed from June 2002 to March 2004. Four wetlands were used and the size of each one was 0.8ha. Water of Dangjin stream flowing into Seokmun estuarine reservoir was pumped into wetlands. Inflow and hydraulic residence time of the system was 500 $m^3$/day∼1,500 $m^3$/day, 2∼5 days, respectively. After 2 year operation, plant-coverage of the wetlauds was about 70% from bare soil surface at initial stage . Average water quality of the influent was $BOD_5$ 4.17 mg/L, TSS 18.45 mg/L, T-N 4.32 mg/L, and T-P 0.30 mg/L. The average removal rate of $BOD_5$, TSS, T-N and T-P during the study period was 5.6%, 46.6%, 45.7%, and 54.8%, respectively. Organic ($BOD_5$) removal rate was low and the reason might be low influent concentration. Wetland removal rate of T-P was about 10% higher than T-N. Performance of the experimental system was compared with existing data base (NADB), and it was within the range of general system performance. Overall, the wetland system was found to be adequate for treating polluted water stream with stable removal efficiency even during the winter period. Most of the nonpoint source pollutions from watershed are transported by streams or ditches, and they could be controled by constructed wetland system before entering the lake or reservoir.

• Journal of Welding and Joining
• /
• 제13권4호
• /
• pp.55-64
• /
• 1995

A study was made to examine the effects of postweld heat treatment(PWHT) on the toughness and microstructures in the weld heat affected zone(HAZ) of Cu-bearing HSLA-100 steel. The Gleeble thermal/mechanical simulator was used to simulate the weld HAZ. The details between toughness and PWHT of HAZ were studied by impact test, optical microscopy(O.M.), scanning electron microscopy (SEM), transmission electron microscopy(TEM) and differential scanning calorimetry(DSC). The decrease of HAZ toughness in single thermal cycle comparing to base plate is ascribed to the coarsed-grain formed by heating to 1350.deg.C. The increase of HAZ toughness in double thermal cycle comparine to single thermal cycle is due to the fine ferrite(.alpha.) grain transformed from austenite(.gamma.)formed by heating to .alpha./.gamma. two phase region. Cu precipitated during aging for increasing the strength of base metal is dissolved during single thermal cycle to 1350.deg.C and is precipitated little on cooling and heating during subsequent weld thermal cycle. It precipitates by introducing PWHT. Thus, the decrease of toughness in triple thermal cycle of $T_{p1}$ = 1350.deg.C, $T_{p2}$ = 800.deg.C and $T_{p3}$ = 500.deg.C does not occur owing to the precipitation of Cu. The behaviors of Cu=precipitates in HAZ is similar to that in base plate. PWHT at 550.deg.C shows highest hardness and lowest toughness, whereas PWHT at 650.deg.C shows reasonable toughness, which improves the toughness of as-welded state.state.

• Journal of Electrochemical Science and Technology
• /
• 제8권3호
• /
• pp.222-235
• /
• 2017

First, in this study, the inhibition efficiencies of metal complexes with Cu(II), Ni(II) and Zn(II) of STSC ligand for corrosion control of mild steel in oilfield formation water were investigated. The IEs for a mixture of 500 ppm STSC and 5 ppm metal ion ($Cu^{+2}$, $Ni^{+2}$, $Zn^{+2}$) were found to be 88.77, 87.96 and 85.13 %, respectively. The results were obtained from the electrochemical techniques such as open circuit potential, linear and tafel polarization methods. The polarization studies have showed that all used Schiff base metal complexes are anodic inhibitors. The protective film has been analyzed by FTIR technique. Also, to detect the presence of the iron-inhibitor complex, UV-Visible spectral analysis technique was used. The inhibitive effect was attributed to the formation of insoluble complex adsorbed on the mild steel surface and the adsorption process follows Langmuir adsorption isotherm. The surface morphology has been analyzed by SEM. Secondly, the computational studies of the ligand and its metal complexes were performed using DFT (B3LYP) method with the $6-311G^{{\ast}{\ast}}$ basis set. Finally, it is found that the experimental results were closely related to theoretical ones.

• Journal of Welding and Joining
• /
• 제14권3호
• /
• pp.48-57
• /
• 1996

A study was made to examine the characteristics of base metal and stress relief cracking(SRC) of heat affected zone(HAZ) for HY-100 and Cu-bearing HSLA-100 steels. The Gleeble thermal/mechanical simulator was used to simulate the SRC/HAZ. The details of mechanical properties of base plate and SRC tested specimens were studied by impact test, optical microscopy and scanning electron microscopy. The specimens were aged at $650^{\circ}C$ for HSLA-100 steel and at $660^{\circ}C$ for HY-100 steel and thermal cycled from $1350^{\circ}C$ to $25^{\circ}C$ with a cooling time of $\Delta$t_${800^{circ}C/500^{circ}C}$=21sec. corresponds to the heat input of 30kJ/cm. The thermal cycled specimens were stressed to a predetermined level of 248~600MPa and then reheated to the stress relief temperatures of $570~620^{\circ}C$. The time to failure$(t_f)$ at a given stress level was used as a measure of SRC susceptibility. The strength, elongation and impact toughness of base plate were greater in HSLA-100 steel than in HY-100 steel. The time to failure was decreased with increasing temperature and/or stress. HSLA-100 steel was more susceptible to stress relief cracking than HY-100 steel under same conditions. It is thought to be resulted from the precipitation of $\varepsilon$-Cu phase by dynamic self diffusion of solute atoms. By the precipitation of $\varepsilon$-Cu phase, the differential strengthening of grain interior relative to grain boundary may be greater in the Cu-bearing HSLA-100 steel than in HY-100 steel. Therefore, greater strain concentration at grain boundary of HSLA-100 steel results in the increased SRC susceptibility. The activation energies for SRC of HSLA-100 steel are 103.9kcal/mal for 387MPa and 87.6kcal/mol for 437MPa and that of HY-100 steel is 129.2kcal/mol for 437MPa.

• 한국정밀공학회지
• /
• 제25권4호
• /
• pp.108-117
• /
• 2008

A transmission designed with P.T.O(Power Take-Off) axle for agricultural work vehicles including multi-purpose vehicles has been developed. It is focused on the 4-wheel drive transmission of synchronous contact type for practical use in fruit tree households which is required for a large-sized agricultural vehicle. Concerning to the specification performed, the load capacity is from 500kg to 1,000kg and the safety should be secured for passengers. In addition, the driving condition should also be secured under bad situations of the topographic slope, swampy land and the rest. In order to carry out above tests, a prototype vehicle through strength analysis of transmission design has been manufactured. Consequently, optimal design conditions on the power transmission with multi-purpose vehicle for various jobs are proposed such as an indication of optimal RPM and torque at a certain work situation. The performance test through the prototype of multi-purpose work vehicle is performed and the related data base is achieved. Finally, it is improved on troubles by the analysis of the results of R&D and provided the solutions on problems occurring to mass production in the future.

• 대한전자공학회논문지SD
• /
• 제42권9호
• /
• pp.1-8
• /
• 2005

최근 Mobile용 RF ICs 적용을 위한 RF CMOS 기술과 함께 핵심 기술로 SiGe Heterojunction Bipolar Transistor (HBT) 소자 개발의 중요성이 증대되고 있다. 본 논문은 현재 5GHz 동작 수준의 RF제품에서 주로 사용되는 기술인 $0.35\{mu}m$ 설계 Rule을 적용하여 $f_{max}$ 50GHz에서 동작하는 SiGe BiCMOS 기술 개발에 대한 내용을 논의한다. 본 SiGe HBT에 사용하는 에피막 성장 기술은 Trapezoidal Ge base profile 및 non-selective 방식이고, 에미터 RTA 조건 및 SiGe HBT base에 대한 Vertical Profile 최적화를 수행하였다. hFE 100, $f_{T}\;45GHz,\;NF_{min}\;0.8dB$ 수준으로 우수한 특성 및 기술 경쟁력을 갖는 SiGe BiCMOS 공정 개발 및 양산 기술을 확보하였다. 또한, 기존의 0.35um설계 Rule공정 target떼 부합되는 CMOS소자를 포함시켰으며, RF용 Passive소자로 높은 Q값을 갖는 MIM capacitor(1pF, Q>80), Inductor(2nH $Q\~$l2.5)를 제공하였다

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.694-699
• /
• 2002

In autobody assembly, thin-wall, tubular connections have been used for the frame structure. Recent interest in light materials, such as aluminum or magnesium alloys, has been rapidly growing for weight reduction and fuel efficiency. Due to higher thermal expansion coefficient, low stiffness/strength, and low softening temperature of aluminum and magnesium alloys, control of welding-induced distortion in these connections becomes a critical issue. In this study, the material sensitivity to welding distortion was investigated using a T-tubular connection of three types materials; low carbon steel (A500 Gr. A), aluminum alloy (5456-H116) and magnesium alloy (AZ91C-T6). An uncoupled thermal and mechanical finite element analysis scheme using the ABAQUS software program was developed to model and simulate the welding process, welding procedure and material behaviors. The predicted angular distortions were correlated to the cumulative plastic strains. A unique relationship between distortion and plastic strains exists for all three materials studied. The amount of distortion is proportional to the magnitude and distribution of the cumulative plastic strains in the weldment. The magnesium alloy has the highest distortion sensitivity, followed by the other two materials with the steel connection having the least distortion. Results from studies of thin-aluminum plates show that welding distortion can be minimized by reducing the cumulative plastic strains by preventing heat diffusion into the base metal using a strong heat sink placed directly beneath the weld. A rapid cooling method is recommended to reduce welding distortion of magnesium tubular connections.

• Archives of Pharmacal Research
• /
• 제24권2호
• /
• pp.159-163
• /
• 2001

The accelerated stability of dimethoxy biphenyl monocarboxylate.HCl (DDB-S) was investigated in 6 mg/mL water solution in the pH ranging 2-10 and the temperature of $45-85^{\circ}C$. The observed rate of degradation followed first-order kinetics. The energy of activation for DDB-S degradation was calculated to be 14.1 and 16.5 $Kcal/mole$ at pH 5 and in distilled watery respectively. The degradation rate constant ($K_{25^{\circ}C}$) obtained by trending line analysis of Arrhenius plots for DDB-S was $5.3{\times}10^{-6}h^{-1}$. The times to degrade 10% ($t_{10}$) and 50% $t_{500}$) at $K_{25^{\circ}C}$ were 829 and 5,416 days, respectively. DDB-S exhibited the fastest degradation at pH 10 and the slowest rate at pH 5. In addition, at $K_{65^{\circ}C}$, degradation rate constants of DDB-S were 0.066, 0.059, 5.460, 32.171, and $1.4{\times}10^{-6}h^{-1}$ at pH 2, 5, 8, 10 and in distilled water, respectively. These observations indicated that the rate-pH profile of DDB-S showed general acid-base catalysis reaction in the range of pH 2-10.

• 한국산학기술학회논문지
• /
• 제20권8호
• /
• pp.477-484
• /
• 2019

포유류에 존재하는 Collectin-Placenta 1 (CL-P1)을 포함한 여러 종류의 scavenger 수용체는 주로 내피 세포, 대식 세포 및 평활근 세포 표면에 발현되는 분자이다. 이들 분자는 산화 된 저밀도 지질 단백질 (oxLDL)에 결합하여 처리 할 수 있는 세포 표면 당 단백질이다. 이들 분자 중 케르세틴이 CL-P1 활성화에 어떤 영향을 미치는가를 확인하였다. 케르세틴은 산화 반응을 담당하는 자유 라디칼의 제거제 역할을 하여 산화를 중지시키는 항산화제로 알려져 있다. 본 논문에서는 마우스 CL-P1 유전자 promoter 부분의 전사 시작 점부터 -500 번째 염기까지의 단편을 DNA 중합효소를 이용하여 클로닝 하였다. 그 후에 대식세포 계열인 RAW264.7 및 섬유아세포계열의 NIH3T3 세포에 도입하여 케르세틴이 CL-P1 유전자 발현에 어떠한 영향을 미치는지에 대한 연구를 하였다. 이 부위에는 세포주기 조절 인자인 E2F 결합부위를 비롯해서 여러 종류의 전사 인자가 결합하는 염기서열이 다수 위치하고 있다. 이러한 500염기 단편을 pGL4.10 기본 벡터 및 프로모터에 연결시킨 후 세포에 도입시켰다. 그리고 배양 중에 케르세틴을 처리하여 유전자 발현양을 형광 색소 발현기법으로 측정하였다. 그 결과 유전자 발현이 시작되는 앞쪽 부분의 -250에서 -350사이의 염기들이 CL-P1 단백질을 만드는데 중요하다는 것을 확인하였다. 그 중에서도 E2F결합 부위가 결정적인 것 이라는 것을 DNA 돌연변이 실험을 통해 확인 하였다. 또한 부착 세포인 RAW264.7 배양액에 케르세틴을 첨가 한 결과, 배양용기 표면에서 탈락하는 현상을 확인하였다. 즉 발현된 CL-P1단백질이 케르세틴에 의해 세표 표면의 부착 분자에도 영향을 주는 것을 확인하였다.