• Computers and Concrete
• /
• 제21권2호
• /
• pp.127-137
• /
• 2018

In this study, the behavior of the number of anchorage bolts on the glass-fiber reinforced polymer (GFRP) plates adhered to the surfaces of reinforcing concrete (RC) T-beams was investigated analytically. The analytical results were compared to the test results in term of shear strength, and midpoint displacement of the beam. The modelling of the beams was conducted in ABAQUS/CAE finite element software. The Concrete Damaged Plasticity (CDP) model was used for concrete material modeling, and Classical Metal Plasticity (CMP) model was used for reinforcement material modelling. Model-1 was the reference specimen with enough sufficient shear reinforcement, and Model-2 was the reference specimen having low shear reinforcement. Model-3, Model-4 and Model-5 were the specimens with lower shear reinforcement. These models consist of a single variable which was the number of anchorage bolts implemented to the GFRP plates. The anchorage bolts of 2, 3, and 4 were mutually mounted on each GFRP plates through the beam surfaces for Model-3, Model-4, and Model-5, respectively. It was found that Model-1, Model-3, Model-4 and Model-5 provided results approximately equal to the test results. The results show that the shear strength of the beams increased with increasing of anchorage numbers. While close results were obtained for Model-1, Model-3, Model-4 and Model-5, in Model-2, the rate of increase of displacement was higher than the increase of load rate. It was seen, finite element based ABAQUS program is inadequate in the modeling of the reinforced concrete specimens under shear force.

• 한국자기공명학회논문지
• /
• 제17권1호
• /
• pp.11-18
• /
• 2013

Rapid advances of computational power and method have made it practical to apply the time-consuming calculations with all-atom force fields and sophisticated potential energies into refining NMR structure. Added to the all-atom force field, generalized-Born implicit solvent model (GBIS) contributes substantially to improving the qualities of the resulting NMR structures. GBIS approximates the effects that explicit solvents bring about even with fairly reduced computational times. Although GBIS is employed in the final stage of NMR structure calculation with experimental restraints, the effects by GBIS on structures have been reported notable. However, the detailed effect is little studied in a quantitative way. In this study, we report GBIS refinements of ubiquitin and GB1 structures by six GBIS models of AMBER package with experimental distance and backbone torsion angle restraints. Of GBIS models tested, the calculations with igb=7 option generated the closest structures to those determined by X-ray both in ubiquitin and GB1 from the viewpoints of root-mean-square deviations. Those with igb=5 yielded the second best results. Our data suggest that the degrees of improvements vary under different GBIS models and the proper selection of GBIS model can lead to better results.

• 한국추진공학회지
• /
• 제5권3호
• /
• pp.79-86
• /
• 2001

6분력 시험대는 추력 벡터 제어 방식 추진기관의 성능지수를 측정하는 시험 장비이다 본 논문은 6분력 시험대의 개념 설계 및 시험 분석 단계에서 가장 중요한 요소 중 하나인 시험대의 모델링 기법에 대한 연구로 기존 운용중인 시험대에도 적용이 가능한 우수한 모델을 제시하였다. 제안된 모델은 모델 매개변수 결정과정에 최소 자승법을 이용하였으며, 계측용 로드셀의 수량 결정과 시험대의 형상설계 과정에서 발생되는 제약조건을 크게 완화할 수 있었다. 그 결과 정확도, 운용성 구조적 안전성을 크게 높인 시험대 설계를 가능하게 하였다. 교정 및 연소 시험에 적용한 결과 기존 접근방법 보다 훨씬 우수한 정확도를 보였다.

• 한국레이저가공학회지
• /
• 제5권1호
• /
• pp.23-31
• /
• 2002

The uniform metal droplet generation using Nd-YAG laser was studied and experiment was carried out. The shape and volume of developed droplet was measured and the Young-Laplace equation and equilibrium condition of force were applied this model. The differential equation predicting shape of droplet using equilibrium condition of force instead of Navier-stokes equation was induced and numerical solution of differential equation compared with experimentation data. The differential equation was solved by Runge-Kutta method. Surface tension coefficient of droplet was determined with numerical solution relate to experimental result under the statical condition. In case of dynamic vibration, metal droplet shape and detaching critical volume are predicted by recalculating proposed model. The result revealed that this model could reasonably describe the behavior of molten metal droplet on vibration.

• 한국공작기계학회논문집
• /
• 제10권5호
• /
• pp.96-103
• /
• 2001

The quality requirements for thickness accuracy in cold rolling continue to become more stringent, particularly in response to exacting design specification from automotive customers. One of the major impacts from the tighter tolerance level is more unusable product on the head end and tail end of tandem mill coils when the mill is in transition to or from steady state rolling condition. A strip thickness control system for a tandem cold steel rolling mills is composed with blocked non-interacting controller and controllers for strip thickness and tension control of each rolling stands. An intelligent mathematical model included an elastic deformation of strip has been developed and applied to the field in order to predict the rolling force. The simulated results showed that the effect of elastic recovery should be included the model, even if the effect of elastic compression was not important.

• Korean Chemical Engineering Research
• /
• 제55권2호
• /
• pp.201-213
• /
• 2017

물이 포함된 원유는 oil separator 를 거쳐 물이 제거된다. 본 연구의 목적은 공기-물-기름 3상 혼합물에 대한 3차원 oil separator 의 분리성능을 예측하기 위하여 Eulerian 전산유체역학(CFD: computational fluid dynamics) 모델을 개발하는 것이다. 비압축성, 등온, 비정상상태 CFD 모델식은 공기상을 연속상으로, 물과 기름상을 분산상으로 정의하며, 운동량 보존식은 항력(drag force), 양력(lift force), 다공성매체 저항력을 포함한다. 또한, 난류현상으로 standard k-${\varepsilon}$ 모델이 이용된다. 물과 기름 출구압은 oil separator 의 액위를 결정하는 중요한 인자이며, 정상운전상태 액위 25 cm를 맞추기 위하여 측정압은 각각 6.3 kPa, 5.1 kPa으로 결정되었다. 시간에 따른 공기, 물, 기름의 부피분율의 변화를 조사하였고, 정상상태에 도달하였을 때, 물과 기름상의 침강속도를 oil separator의 종축 길이에 따라 분석하였다. 본 연구에서 제시된 CFD 모델로부터 얻은 oil separator의 기름분리성능은 99.85%이며, 실험값과 거의 일치하였다. 비교적 단순한이 CFD 모델은향후 oil separator의구조를 변경하거나, 최적운전조건을 찾기위하여 유용하게사용될수있을 것이다.

• 대한토목학회논문집
• /
• 제26권5A호
• /
• pp.887-899
• /
• 2006

본 연구의 목적은 교량 거더 단면의 공기역학적 특성을 나타내는 기본 자료인 공기력계수와 플러터계수가 동적응답과 어떠한 상관관계를 가지는지를 규명하는데 있다. 이를 위해 세 단계의 단면모형실험이 수행되었다. 첫 번째 단계에서는 총 7개의 거더 단면 즉, 6개의 플레이트거더 단면과 1개의 박스거더 단면이 고려되었으며 거더 단면의 기하학적 형상, 영각, 바람의 방향 그리고 기류조건이 공기력계수인 항력계수, 양력계수 그리고 모멘트계수에 미치는 영향을 정적 단면모형실험을 통해 살펴보았다. 두 번째 단계에서는 동적실험을 통해 각 단면의 공기력계수와 동적응답의 상관성을 검증하였다. 마지막으로 2자유도하의 동적 단면모형실험을 통해 세 개의 거더 단면의 플러터계수를 산출하고 이를 동적실험결과와 비교하였다. 주어진 단면형상에 대한 비정상 공기력에 의해 변화되는 시스템의 감쇠와 강성을 가장 잘 반영하는 플러터계수는 초기변위-자유진동시스템을 이용하여 추출하였다. 이를 위해 등류조건에서 풍속별로 교량단면의 수직 및 비틀림 초기변위의 시간에 따른 진폭의 감쇠를 측정하였다. 본 연구에서 제시한 교량단면의 공기력계수와 플러터계수는 공탄석해석 및 버펫팅해석을 위한 기본 자료로 유용하게 쓰일 것으로 보인다.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제50권5호
• /
• pp.211-217
• /
• 2001

In this paper, we have developed the 6 DOF force display system to be based on the single PC. The system is composed of the force display device, the force reflecting rendering algorithm and the high-speed controller. The previous systems had a problem, that must adopt high performance workstation or 2-PC in order to control the graphics speedily and stably. In this paper, it is possible to improve the problem as to develop its exclusive controller and new rendering algorithm. The proposed new rendering algorithm is based on the Proxy algorithm, which can convert information of the position, the velocity, and the haptic information into the force-data. Especially, as to use the proxy algorithm, we can construct dynamical virtual-environment with the elasticity, the viscosity, the mass, and the friction force. As the result of the experiment, we found that our system has much superior characteristics than some other haptic interfaces, because it can control of 30,000 polygon model constructed virtual object with 1[kHz] haptic interrupt cycle and 20[Hz] graphic interrupt cycle in the single PC based system.

• 한국정밀공학회지
• /
• 제23권5호
• /
• pp.149-154
• /
• 2006

The cold expansion method (CEM) is one of the widely used a method to improve the fatigue behavior of materials in aerospace industry. Such improvement is due to the compressive residual stress developed when a tapered mandrel goes through the fastener holes a little smaller than the mandrel. CEM is retarded of crack initiation due to the compressive residual stress developed on the hole surface. Many researchers are studied a finite element analysis of residual stress around fastener hole. But in case of real model, fastener hole has a clamping force after CE. Therefore, it is respected that residual stress distributions should be changed due to clamping forces. In this paper, it was performed finite element analysis of residual stress by clamping force after CE in the plate having adjacent holes. From this study, it has been found that compressive residual stress near the hole increases according to clamping force. Also, the more increase clamping force, the more increases compressive residual stress. However, tensile residual stress increase beyond clamping force area.

• 한국구조물진단유지관리공학회 논문집
• /
• 제5권2호
• /
• pp.163-174
• /
• 2001

This paper is to study the characteristics of axial force behavior that operates to the part of turnout when it makes the turnout and the continuous welded rail unifying. The study is to model by using the 50kgN rail No. 15 turnout used in the domestic national railway and the UIC60 rail No. 18 turnout used in the rapid transit railway as the finite elements for analyzing the axial force behavior of the turnout by the continuous welded rail. It is to analyze the characteristics of behavior according to the change of creep resistance, ballast resistance and the change of parameter valuables of heel joint by the axial force simulation in making the continuous welded rail and then, it is to present the result. As the result of research on the parameter valuables through the analysis, it shows that the maximum axial force of turnout by the continuous welded rail are largely subordinated to the maximum resistance of heel joint and the fitting devices than the ballast resistance. Also it shows that the maximum axial force produced changes a lot according to the characteristics of creep resistance of the fitting part and the ballast resistance.