• International Journal of Automotive Technology
• /
• 제8권2호
• /
• pp.137-147
• /
• 2007

Homogenous Charge Compression Ignition (HCCI) combustion systems can be broadly divided for the process applied to 4-stroke and 2-stroke engines. The former process is often referred to as simply HCCI combustion and the latter process as Active Thermo-Atmosphere Combustion (ATAC). The region of stable engine operation tends to differ greatly between the two processes. In this study, it was shown that the HCCI combustion process of a 4-stroke engine, characterized by the occurrence of autoignition under a high compression ratio, a lean mixture and wide open throttle operation, could be simulated by operating a 2-stroke engine at a higher compression ratio. On that basis, a comparison was made of the combustion characteristics of high-compression-ratio HCCI combustion and ATAC, characterized as autoignited combustion in the presence of a large quantity of residual gas at a low compression ratio and part throttle. The results showed that one major difference between these two combustion processes was their different degrees of susceptibility to the occurrence of cool flame reactions. Compared with high-compression-ratio HCCI combustion, the ignition timing of ATAC tended not to change in relation to different fuel octane numbers. Furthermore, when internal EGR was applied to high-compression-ratio HCCI combustion, it resulted in combustion characteristics resembling ATAC. Specifically, as the internal EGR rate was increased, the ignition timing showed less change in relation to changes in the octane number and the region of stable engine operation also approached that of ATAC.

• 대한기계학회논문집
• /
• 제18권4호
• /
• pp.920-932
• /
• 1994

The combustion phenomena of a reciprocating engine is one of the most important processes affecting performance and emissions. One effective way to improve the engine combustion is to control the motion of the charge inside a cylinder by means of optimum induction system design, because the flame speed is mainly determined by the turbulence at compression(TDC) process in S.I. engine. It is believed that the tumble and swirl motion generated during intake breaks down into small-scale turbulence in the compression stroke of the cycle. However, the exact nature of their relationship is not well known. This paper describes cycle resolved LDV measurement of turbulent flow inside the cylinder of a 4-valve engine under motoring(non-firing) conditions, and studies the effect of intake port configurations on the turbulence characteristics using following parameters ; Eulerian temporal autocorrelation coefficient, turbulence energy spectral density function, Taylor micro time scale, integral time scale, and integral length scale.

• Journal of Advanced Marine Engineering and Technology
• /
• 제12권4호
• /
• pp.53-61
• /
• 1988

Speed of a diesel engine is usually controlled by the hydraulic governor which uses the centrifugal force of rotating fly balls for sensing the error speed. But for a recently developed high efficient, low speed and long stroke 2 cycle marine diesel engine, this governor doesn't work well enough because of too much changes of toraring force during one revolution of engine and too long uncontrollable time due to small numbers of cylinder. For improvement of jiggling phenomena and unstability various studies are being carried out, but they are not enough for a steep load change in a small ship's generator plant or at rough sea condition in a propulsion engine. In this paper, authors propose a new method to control a fuel before the change of angular velocity due to load change by feedforward the change of load, and find that the proposed method shows quite a good control performance in comparision to the customary PID control method by simulation using a digital computer for the various load change.

• 기술사
• /
• 제34권2호
• /
• pp.31-36
• /
• 2001

The Otto Cycle of conventional gasoline engine has no difference between compression ratio and expension ratio. because of the same length of 4 strokes : Intake, compression, expension, exhaust. On the other hand, miller cycle engine achieves both low-compression ratio and high-compression ratio by shortening the length of compression stroke among 4 strokes. Therefore miller cycle engine is essential for lessening knocking and improving heat efficiency. This paper Is designed to discribe not only principle and the development trend of miller cycle engine but also the control system and the technical characteristics of it.

• 오토저널
• /
• 제7권1호
• /
• pp.24-34
• /
• 1985

The study of unsteady gas exchange processes in the inlet and exhaust systems of the single-cylinder 4-stroke cycle spark ignition engine is presented in this paper. The generalized method of characteristics including friction, heat transfer, change of flow area and entropy gradients was used for solving the equations defining the gas exchange process. The path line calculation was also conducted to allow for calculation of the gas composition and entropy change along the path lines, and of the variable specific heat due to the change of temperature and composition. As the result of the simulation, the properties at each point in the inlet and exhaust pipe, pressure and temperature in the cylinder, and charging efficiency were obtained. Pumping loss and residual gas fraction were also computed. The effect of engine speed, exhaust and inlet pipe length on the pumping loss and charging efficiency were studied showing that the results were in agreement with what has been known from experiments.

• 한국자동차공학회논문집
• /
• 제19권2호
• /
• pp.78-83
• /
• 2011

Diesel engine has many advantages such as high thermal efficiency, low fuel consumption and low emission of CO2. However, the diesel engine faced with strengthened emission regulation about NOx and PM. To suppress NOx emission, after-treatment systems such as Lean NOx Trap (LNT), Selective Catalytic Reduction (SCR) are considered as a more practical strategy. This paper investigated the performance of Lean NOx trap of the 4 stroke diesel engine which had a LNT catalyst. Characteristic of exhaust emission at NEDC mode was analyzed. From this result, the effect of nozzle attaching degree, injection quantity and gas flow change on NOx conversion performance was clarified.

• 오토저널
• /
• 제7권3호
• /
• pp.74-82
• /
• 1985

Using single-zone heat release model and quasi-steady model, computer program for calculating the compression ignition engine cycle was composed. The properties in the cylinder were calculated in terms of crank angle and the effects of various operating conditions on rate of heat release and on engine performance were studied. The predicted values for the engine under consideration have shown good agreement with published data.

• Journal of Mechanical Science and Technology
• /
• 제15권1호
• /
• pp.108-116
• /
• 2001

The in-cylinder flow field of gasoline engine comprises unsteady compressible turbulent flows caused by the intake port, combustion chamber geometry. Thus, the quantitative analysis of the in-cylinder flow characteristics plays an important role in the improvement of engine performances and the reduction of exhaust emission. In order to obtain the quantitative analysis of the in-cylinder gas flows for a gasoline engine, the single-frame particle tracking velocimetry was developed, which is designed to measure 2-dimensional gas flow field. In this paper, influences of the swirl and tumble intensifying valves on the in-cylinder flow characteristics under the various intake flow conditions were investigated by using this PTV method. Based on the results of experiment, the generation process of swirl and tumble flow in a cylinder during intake stroke was clarified. Its effect on the tumble ratio at the end of compression stroke was also investigated.

• 오토저널
• /
• 제10권6호
• /
• pp.25-38
• /
• 1988

As a mean of increasing engine power, great attention has been concentrated on the turbo-charging owing to better fuel economy, smaller engine size and lower emission. The performance in turbocharged engine depends not only on the efficiency of the engine and the turbocharger used, but also on the total characteristics of the system by the matching turbocharger to the engine. The matching of the turbocharger to the engine has been usually accomplished by the empirical techniques with a great deal of laborious work. It would be better to predict the performance and emission in the turbocharged engine using the effective simulation model. In this study, computer simulation program has been developed to predict the transient variation of properties of gas in the cylinder, intake and exhaust pipes, the engine performances and emissions.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권2호
• /
• pp.126-131
• /
• 2007