• 대기
• /
• 제25권3호
• /
• pp.511-520
• /
• 2015

Existing studies on radar rainfall uncertainties were performed to reduce the uncertainty for each stage by using bias correction during the quantitative radar rainfall estimation process. However, the studies do not provide quantitative comparison with the uncertainties for all stages. Consequently, this study proposes a suitable approach that can quantify the uncertainties at each stage of the quantitative radar rainfall estimation process. First, the new approach can present initial and final uncertainties, increasing or decreasing the uncertainty, and the uncertainty percentage at each stage. Furthermore, Maximum Entropy (ME) was applied to quantify the uncertainty in the entire process. Second, for the uncertainty quantification of radar rainfall estimation at each stage, this study used two quality control algorithms, two rainfall estimation relations, and two bias correction techniques as post-processing and progressed through all stages of the radar rainfall estimation. For the proposed approach, the final uncertainty (ME = 3.81) from the ME of the bias correction stage was the smallest while the uncertainty of the rainfall estimation stage was higher because of the use of an unsuitable relation. Additionally, the ME of the quality control was at 4.28 (112.34%), while that of the rainfall estimation was at 4.53 (118.90%), and that of the bias correction at 3.81 (100%). However, this study also determined that selecting the appropriate method for each stage would gradually reduce the uncertainty at each stage. Finally, the uncertainty due to natural variability was 93.70% of the final uncertainty. Thus, the results indicate that this new approach can contribute significantly to the field of uncertainty estimation and help with estimating more accurate radar rainfall.

• 한국결정성장학회지
• /
• 제3권2호
• /
• pp.167-175
• /
• 1993

여러 가지 탄소물질을 사용하여 변형된 스테인레스 금속재 Two-bulbs를 사용하여 Li-CIC를 합성하였다. 합성한 결과 출발물질의 구조적 특성에 따라 여러 가지 색깔의 층간화합물이 각각 형성되었다. 합성된 Li-CIC들은 X-선 회절법을 이용하여 출발물질의 결정화도에 따라 stage 형성과정을 확인하였다. 이들 결과에서 출발물질의 결정화도가 좋은 천연흑연과 흑연섬유는 낮은 stage(1 stage, 2 stage)가 형성되었고, 결정화도가 나쁜 탄소섬유와 석유계 코크스는 높은 stage(3 stage, 4 stage, 5 stage)가 얻어졌다. 또한 (hkl)회절선의 이값을 계산된 값과 비교하였을 때 이들 값들은 거의 일치하였다. 그러나 결정화도가 나쁜 경우 다소의 차이가 있음을 보이고 있다. 이들 Li-CIC에 대하여 UV/VIS 분광기를 사용하여 stage 안정성과 에너지 상태를 알수 있었다. X-선 회절법에 의한 결과와 UV/VIS 분광학적 데이터는 결정화도가 좋은 탄소물질은 에너지와 반사율의 관계곡선이 뚜렷하게 나타났음을 제시하였다. 이들 결과는 타소층과 층사이에 전하운반자와 관계가 있으며, 이들 성질이 삽입물질의 농도와 관계있음을 알수 있었다. 뿐만 아니라 본 연구는 Li-CIC의 삽입과정에서 고성능 에너지 저장제에 대한 정보를 역시 제공하여 준다.

• 한국보건간호학회지
• /
• 제18권2호
• /
• pp.205-217
• /
• 2004

This study conducted a survey with the 67 students who are in their 2nd year at 3 vocational high schools. The researcher of this study developed and operated the smoking cessation program based on the Transtheoretical model. To evaluate the effects, experiments were repeatedly done. The data were collected from June 21, 2004 till July 9, 2004. The survey was done based on the questionnaire-interview before and after education. The collected date was computerized by using SPSS-WIN 10.0 program. The results are as follows: Firstly. before education, the smoking cessation stage of change shows precontemplation stage $37.3\%$, preparation stage $37.3\%$, and contemplation stage $25.4\%$ respectively. However, after education it shows preparation stage $44.8\%$, action stage $25.4\%$, contemplation stage $19.4\%$, precontemplation stage $10.4\%$. The positive result was $62.7\%$ and smoking cessation stage of change made a 0.9 step increase. Secondly, process of change rose in all the areas except helping relationship. It also shows statistical improvement in all the fields except the dramatic relief of the experiential process, the helping relationship of behavioral process and stimulus control Thirdly, negative affective situation temptation, positive social situation temptation, and habitual strength temptation's average points decreased but showed statistical differences. Weight control temptation's average points decreased after education but didn't show statistical differences. Self efficiency increased measurably after education. Fourthly, concerning the social pros and coping pros caused by smoking, the average points were low after education and showed statistic decrease. As for the cons due to smoking, the average points increased but didn't show any statistical differences. In conclusion, thanks to the smoking cessation program applied by the Transtheoretical model, the smoking rate of vocational high school students became low and their smoking temptation also dropped considerably. In conclusion, while the pros for smoking were lessened, its corns were heightened through the educational awareness offered by this program.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.237-237
• /
• 2010

We investigated physical properties of CuIn1-xGaxSe2 thin films grown by co-evaporator under various Cu environments. To study the effect of the Cu environments on absorber layer properties, thin films were fabricated under various reaction periods for different Cu flux on 2 stage process. We find the structural and electrical characteristics were affected by the reaction period on 2 stage process. The correlation between Cu flux variation on 2 stage process and solar cell performance was studied. The structural and electrical properties for various Cu flux were discussed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.195-200
• /
• 2007

We analyzed a sequence of multi-stage automatic cold forging processes composed of four axisymmetric processes followed by a non-axisymmetric process using rigid-plastic finite element based forging simulators. The forging sequence selected for an example involves a piercing process and a heading process accompanying folding or overlapping, which all make it difficult to simulate the processes. To reduce computational time and to enhance the solution reliability, only the non-symmetric process was analyzed by the three-dimensional approach after the axisymmetric processes were analyzed by the two-dimensional approach. It has been emphsized that this capability is very helpful in simulating the multi-stage automatic forging processes which are next to axisymmetric.

• 한국생산제조학회지
• /
• 제19권6호
• /
• pp.760-767
• /
• 2010

Even though a flexible disk grinding process was often applied to enhance the product quality, it produced non-flat zone in the beginning and the exit (end) area. Since latter area is susceptible to poor product quality with burn mark, careful analysis is required to cope with such degradation. The flexible disk grinding exit stage was analyzed for workpiece length, wheel speed, depth of cut and feed. The exit stage qualities defined as exit stage ratio and exit stage angle or slope was characterized. A neural network application results reveled that exit stage characteristics was predicted more accurately without workpiece dimension with minimum error of 1.3%.

• 플랜트 저널
• /
• 제5권3호
• /
• pp.59-65
• /
• 2009

In the plant EPC project, the procurement work can be considered as the most important part that affects the success or failure of project as it has the closest mutual influence in every execution process of the project. Procurement takes up generally 60% ~ 70% of the entire project budget and the current trend of plant EPC project becoming larger in scale and a variety of process technology being applied. So, it is needed to identify the risks that are expected to occur according to the stages of procurement work, namely, proposal stage, manufacturer selection and purchasing agreement stage, expediting the process management of manufacturer stage, inspection stage and logistics & transportation stage. The management of observation and control of the risks should be performed with the response techniques which are 'avoid',' transfer'and' mitigate'.

• 한국식품저장유통학회지
• /
• 제4권3호
• /
• pp.337-341
• /
• 1997

Texture is an important quality factor of processed chestnut products, which changes depending on the conditions of boiling process. The conventional boiling process consists of three stage(1st : 70 minutes at 60$^{\circ}C$; 2nd : 20minutes at 70$^{\circ}C$; 3rd : 80minutes at 98$^{\circ}C$). To improve the conventional boiling process of processed chestnut products, we investigated the changes of texture at different stages of boiling process and undertook the optimization of boiling process by response surface method on heating times of 2nd and 3rd heating, and amount of softening agent. The initial hardness and cohesiveness, the most important textural characteristics of chestnut, were 7.876kg and 0.189, respectively. In the third boiling stage, hardness decreased to 0.313kg and cohesiveness increased to 0.310. Using response surface method the minimum point of hardness and maximum point of cohesiveness was examined and model equations for predicting the changes of hardness and cohesiveness in the optional boiling condition were developed.

• 소성∙가공
• /
• 제23권4호
• /
• pp.211-220
• /
• 2014

The outer race of a constant velocity (CV) joint having six inner ball grooves has traditionally been manufactured by multi-stage warm forging, which includes forward extrusion, upsetting, backward extrusions, necking, ironing and sizing, and machining. In the current study, a multi-stage cold forging process is examined and an assessment for replacing and modifying the conventional multi-stage warm forging is made. The proposed procedure is simplified to the backward extrusion of the conventional process, and the sizing and necking are combined into a single sizing-necking step. Thus, the forging surface of the six ball grooves can be obtained without additional machining. To verify the suitability of the proposed process, a 3-dimensional numerical simulation on each operation was performed. The forging loads were also predicted. In addition, a structural integrity evaluation for the tools was carried out. Based on the results, it is shown that the dimensional requirements of the outer race can be well met.

• 기술경영경제학회:학술대회논문집
• /
• 기술경영경제학회 1997년도 제11회 하계학술발표회 논문집
• /
• pp.124-159
• /
• 1997

This paper examines a significant example of accumulation of technology in post war Japan - the development process of the videocasstte recorder (VCR) for home use, and the dynamic evolution process of the mass market. The purpose of analyzing the Japanese home VCR industry is to clarify how and why only the Japanese makers had succeeded in developing home VCR and dominated. the global mass market and to make clear the dynamic process of industrial evolution. This study found out the following facts; 1) Japanese inter-firm interactions in the VCR have been carried out by the structure of "the competition and cooperation among the engaged players" form the initial stage, to growing, and maturing stage. 2) The process of competition and cooperation produced the revolutionary innovation through a continuous systematic development process in the R&D phase. 3) The process of competition and cooperation accelerated the speed of technological progress and the rapid growth of the industry in the growing and maturing stage.