• Journal of Radiation Industry
• /
• v.6 no.2
• /
• pp.159-164
• /
• 2012

Bacterial cellulose (BC) is generated from citrus gel by Gluconacetobacter hansenii TL-2C. BC has good properties such as high-burst pressure, high-water contact and the ultrafine highly nanofibrous structure of mimic natural extracellular matrix (ECM) for tissue engineering. In this study, acrylic acid (AAc) was grafted onto BC surfaces under aqueous conditions using gamma-ray irradiation, and then immobilized gelatin onto AAc-g-BC. The characterization of scaffolds was performed by scanning electron microscopy (SEM), attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR), toluidine blue O (TBO) assay. Morphology of gelatin and AAc incorporation onto BC nanofibers did not changed. Our study suggests that gelatin-immobilized BC nanofibers scaffold has a potentiality to fabricate 3D nanofibrous scaffolds for tissue engineering.

• Korean Journal of Metals and Materials
• /
• v.49 no.12
• /
• pp.983-988
• /
• 2011

Failure analyses of the screws in spinal fixation devices were carried out. The fractured screws were retrieved from a patient who had spinal surgery in the thoracic vertebrae from number 10 to 15. The failure occurred one month after the removal of the braces. Microstructures and fracture surfaces were examined by optical and scanning electron microscopy. The microstructures of the screws corresponded to annealed Ti-6Al-4V bar. However, in the vicinity of the screw surface, there was an insufficient number of fine precipitates. Fracture surfaces showed typical fatigue failure modes. Regarding the fact that no machining defects were detected, fatigue crack initiation might have been caused by the lack of precipitates near the screw surfaces. Only the fourth of five fixed screws was severely stress-concentrated by the action of the spinal bones, while the stress of the 4th screw was decreased to half of its acceptable level when the screw was supplemented by one more, which might have been fixed in the 6th vertebra under the 5th position by the switching of its position. The stress simulation was conducted by ANSYS with 3D CAD of PRO/E in order to understand the stress concentration behavior and to provide an effective spinal surgery guide.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.10
• /
• pp.236-242
• /
• 2019

Recently, scanning projects have been carried out in various construction and construction fields for maintenance purposes. The point cloud generated by the scan results is composed of a number of points representing the object to be scanned. The process of extracting the necessary information, including dimensions, from such scan data is called paradox. The reverse engineering process of modeling a point cloud as BIM involves considerable manual work. Owing to the time-consuming reverse engineering nature of the work, the costs increase exponentially when rework requests are made, such as design changes. Reverse engineering automation technology can help improve these problems. On the other hand, the reverse design product is variable depending on the use, and the kind and detail level of the product may be different. This paper proposes the G2BM (Geometry-to-BIM mapping) rule definition method that automatically maps a BIM object from a primitive geometry to a BIM object. G2BM proposes a process definition and a customization method for reverse engineering BIM objects that consider the use case variability.

• Journal of Veterinary Clinics
• /
• v.38 no.2
• /
• pp.75-81
• /
• 2021

An aquariid nematode, Desportesius invaginatus, was found in the proventriculus of an Egretta garzetta and a Bubulcus ibis from Chuncheon in the Republic of Korea. The worms were identified by light and scanning electron microscopy based on important taxonomic characteristics (body length, esophagus length, cordons, spicules, caudal alae of males, position of the vulva) and then phylogenetically analyzed using the 18S rRNA encoding gene. The nematodes were characterized by a body length of 7.0-8.0 mm in males and 10.2-13.1 mm in females, and two pairs of cordons recurrent in the anterior direction, and cordons were anastomosed by a longitudinal cuticular ridge that externally delimits a longitudinal canal. The widest cuticular plates of cordons bears over 20 posterior spines. The length of the spicules in males was also significantly different. The right spicule measured 742-821 (794) ㎛ in length and 40-45 (42) ㎛ in width, and the left spicule measured 493-556 (541) ㎛ in length and 11-13 (12) ㎛ in width. The caudal alae of males are inflated and vesicular in appearance. The vulva was situated at 56-71 (58.3) ㎛ from the posterior extremity. Although the 18S rRNA sequences of worms were similar to the Synhimantus species, some genetic divergences were observed in comparison. In this study, the worms were recognized with genus Desportesius because genus Desportesius was considered a subgenus of Synhimantus. This is the first record of D. invaginatus in the Republic of Korea.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.41 no.4
• /
• pp.91-100
• /
• 2018

The setting of values on door hinge mounting compensation for door assembly tolerance is a constant quality issue in vehicle production. Generally, heuristic methods are used in satisfying appropriate door gap and level difference, flushness to improve quality. However, these methods are influenced by the engineer's skills and working environment and result an increasement of development costs. In order to solve these problems, the system which suggests hinge mounting compensation value using CAE (Computer Aided Engineering) analysis is proposed in this study. A structural analysis model was constructed to predict the door gap and level difference, flushness through CAE based on CAD (Computer Aided Design) data. The deformations of 6-degrees of freedom which can occur in real vehicle doors was considered using a stiffness model which utilize an analysis model. The analysis model was verified using 3D scanning of real vehicle door hinge deformation. Then, system model which applying the structural analysis model suggested the final adjustment amount of the hinge mounting to obtain the target door gap and the level difference by inputting the measured value. The proposed system was validated using the simulation and showed a reliability in vehicle hinge mounting compensation process. This study suggests the possibility of using the CAE analysis for setting values of hinge mounting compensation in actual vehicle production.

• Tribology and Lubricants
• /
• v.35 no.2
• /
• pp.99-105
• /
• 2019

This study presents an experimental investigation of the wear and oxidation of the bristles of a brush seal in a super-heated steam environment. We construct a model reflecting normal force and radial interference to predict the amount of wear. To monitor the volume loss of the bristle induced by the swirl phenomenon of the rotor, we measure the clearance between the rotor and the brush seal by using a non-contact 3-D device. We calculate the area by using the area-wise measurement method. Considering the obvious brush seal wear variables, we use two disks with different roughness($Ra=0.1{\mu}m$ and $100{\mu}m$) to determine the effect of roughness on wear. Considering an actual steam turbine, we utilize a steam generator and super-heater to generate a working fluid (0.95MPa, 523.15K) that has high kinetic energy. We observe the abrasion of the bristles in the hot steam environment through a scanning electron microscope image. This study also conducted energy dispersive X-ray (EDX) analysis for a qualitative evaluation of local chemistry. The results indicate that the wear and elimination of bristles occur on the disk with high roughness, and the weight increases due to oxidation. Furthermore these results, reveal that the bristle oxidation is accelerated more under super-heated steam conditions than under conditions without steam.

• Composites Research
• /
• v.34 no.1
• /
• pp.47-50
• /
• 2021

In this paper, the Curing process for Epoxy Molding Compound (EMC) Package was developed by comparing the performance of the EMC/Cu Bi-layer package manufactured by the conventional Hot Press process system and Carbon Nanotubes (CNT) Heater process system of the surface heating system. The viscosity of EMC was measured by using a rheometer for the curing cycle of the CNT Heater. In the EMC/Cu Bi-layer Package manufactured through the two process methods by mentioned above, the voids inside the EMC was analyzed using an optical microscope. In addition, the interfacial void and warpage of the EMC/Cu Bi-layer Package were analyzed through C-Scanning Acoustic Microscope and 3D-Digital Image Correlation. According to these experimental results, it was confirmed that there was neither void in the EMC interior nor difference in the warpage at room temperature, the zero-warpage temperature and the change in warpage.

• The Journal of Advanced Prosthodontics
• /
• v.12 no.6
• /
• pp.338-343
• /
• 2020

PURPOSE. The present study aimed to investigate the relationships between the crown form of the upper central incisor and their labial inclination, overbite, and overjet. MATERIALS AND METHODS. Maxillary and mandibular casts of 169 healthy dentitions were subjected to 3D dental scanning, and analyzed using CAD software. The crown forms were divided into tapered, square, and ovoid based on the mesiodistal dimensions at 20% of the crown height to that at 40%. The degree of labial inclination of the upper central incisor was defined as the angle between the occlusal plane and the line connecting the incisal edge and tooth cervix. The incisal edges of the right upper and lower central incisor that in contact with lines parallel to the occlusal plane were used to determine the overbite and overjet. One-way ANOVA was performed to compare the labial inclination, overbite, and overjet among the crown forms. RESULTS. The crown forms were classified into three types; crown forms with a 20%/40% dimension ratio of 1.00±0.01 were defined as square, >1.01 as tapered, and <0.99 as ovoid. The labial inclination degree was the greatest in tapered and the least in square. Both overbite and overjet in tapered and ovoid were higher than those in square. CONCLUSION. Upper central incisor crown forms were related to their labial inclination, overbite, and overjet. It was suggested that the labial inclination, overbite, and overjet should be taken into consideration for the prosthetic treatment or restoring the front teeth crowns.

• Physical Therapy Rehabilitation Science
• /
• v.9 no.4
• /
• pp.230-237
• /
• 2020

Objective: To investigate the physical appearance and therapeutic changes that occur with the performance of Schroth exercise in patients with scoliosis. Design: Randomized controlled trial. Methods: Fifteen subjects with maximum curvature of the lumbar who were diagnosed with idiopathic scoliosis had volunteered to participate in the study. Eight subjects were included in the experimental group where they performed the Schroth Therapeutic Exercise and the other seven were included in the control group. The experimental group underwent 2 hours of weekly treatment for 12 weeks, while the control group did not during the same period based on the decisions of patients or guardians. The Mann-Whitney rank test was carried out to compare the treatment results of the two groups, and the comparison within the group was done by Wilcoxon signed-rank test. The vertebral rotation angle (VRA) was by Scoliometer, and difference of rotated and curved portion volume (DV) between both sides on the major curvature portion measured by 3D human body scanning system. Results: In the experimental group, 12 weeks of Schroth exercise therapy has significant improved in correction rate (CR) in Cobb's angle (CA), VRA, and DV between both sides on the major curvature portion (p<0.05), while significant differences were not found between the groups regarding weight bearing difference in both feet (WD) and DV (p<0.05). Conclusions: Schroth exercise performance showed significant changes in the patient's therapeutic changes (CA, VRA), but the physical appearance (DV, WD) was not significant, indicating that external changes in the treatment goal setting are more difficult goals to achieve.

• The korean journal of orthodontics
• /
• v.52 no.4
• /
• pp.249-257
• /
• 2022

Objective: The purpose of this study was to evaluate and compare the dimensional accuracy between thermoformed and direct-printed aligners. Methods: Three types of aligners were manufactured from the same reference standard tessellation language (STL) file: thermoformed aligners were manufactured using Zendura FLX^TM (n = 12) and Essix ACE^TM (n = 12), and direct-printed aligners were printed using Tera Harz^TM TC-85DAP 3D Printer UV Resin (n = 12). The teeth were not manipulated with any tooth-moving software in this study. The samples were sprayed with an opaque scanning spray, scanned, imported to Geomagic^® Control X^TM metrology software, and superimposed on the reference STL file by using the best-fit alignment algorithm. Distances between the aligner meshes and the reference STL file were measured at nine anatomical landmarks. Results: Mean absolute discrepancies in the Zendura FLX^TM aligners ranged from 0.076 ± 0.057 mm to 0.260 ± 0.089 mm and those in the Essix ACE^TM aligners ranged from 0.188 ± 0.271 mm to 0.457 ± 0.350 mm, while in the direct-printed aligners, they ranged from 0.079 ± 0.054 mm to 0.224 ± 0.041 mm. Root mean square values, representing the overall trueness, ranged from 0.209 ± 0.094 mm for Essix ACE^TM, 0.188 ± 0.074 mm for Zendura FLX^TM, and 0.140 ± 0.020 mm for the direct-printed aligners. Conclusions: This study showed greater trueness and precision of direct-printed aligners than thermoformed aligners.