• Proceedings of the KIEE Conference
• /
• 2007.10c
• /
• pp.83-85
• /
• 2007

This paper presents the vibration reduction of PMLSM according to permanent magnet array. The detent force and the lateral force arc generating the thrust ripple that cause vibration in PMLSM. The detent force, the thrust and the lateral force is analyzed by 3D FEM. And the acceleration sensor is used for experimentation of vibration.

• Journal of the Korean Society of Combustion
• /
• v.23 no.1
• /
• pp.13-20
• /
• 2018

Transverse acoustic mode in annular combustion chambers affects air-fuel mixing characteristics in the nozzle and can result in heat release fluctuations in the combustor. In addition, the acoustic mode coupling between the nozzle and the combustion chamber is one of the key parameters determining combustion instability phenomenon in the annular combustor. In this study, acoustic coupling between the nozzle and annular combustor was numerically analyzed using 3D-based in house FEM code. As a result, it was found that the acoustic mode inside the combustion chamber at anti-node locations of the transverse mode was strongly influenced by the nozzle inlet boundary conditions.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.868-870
• /
• 2001

Salient pole rotor type single phase SRM(switched reluctance motor) can be use axial direction magnetic flux and radial direction magnetic flux at the same time. Then, it has higher energy density per unit volume and can be lessened the shaft length of motor or exciting magnetic force. Additionally, it's durability is good because it is simple structure and driving device. Prototype of Salient pole rotor type single phase SRM was fabricated by using parameters of three phase SRM and 3D FEM analysis. Also, driving device was fabricated for prototype. Speed and torque characteristic was confirmed through the experiments, and flux linkage, which is important parameter of SRM for generating torque, was measured. The induction emf was calculated by using ideal inductance graph and current graph. Calculated emf and measured emf was compared for confirming loss of prototype in this paper.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.385-388
• /
• 2004

The influence of material properties and process parameters on the strain distribution of stamping parts was studied by finite element method. For the parametric study, the investigation of variation of material properties was carried out with tensile test for a dozens of different steel sheets. The friction test for each surface and lubricants conditions are also carried out because the frictional characteristic is important parameter fur sheet metal forming. The geometry of stamping parts was measured by 3D scanner to build the tool model fer the FE analysis. As a result of analysis the major process parameter fer each automotive parts was investigated.

• Journal of Magnetics
• /
• v.17 no.4
• /
• pp.285-290
• /
• 2012

Electric Power Steering (EPS) system is superior to conventional Hydraulic Power Steering (HPS) system in aspect of fuel economy and environmental concerns. The EPS system consists of torque sensor, electric motor, ECU (Electric Control Unit), gears and etc. Among the elements, the torque sensor is one of the core technologies of which output signal is used for main input of EPS controller. Usually, the torque sensor has used torsion bar to transform torsion angle into torque and needs linear characteristic in terms of flux variation with respect to rotation angle of permanent magnet. The torsion angle of both ends of a torsion bar is measured by a contact variable resistor. In this paper, the sensor is accurately analyzed using 3D finite element method and its characteristics with respect to four different shapes of the stator teeth are compared. The four shapes are rectangular, triangular, trapezoidal and circular type.

• Journal of Magnetics
• /
• v.17 no.2
• /
• pp.129-132
• /
• 2012

To evaluate the electromagnetic power absorption in near field, the magnetic composites with the conductive grids were simulated using the typical permeability frequency profiles. The transmission power absorptions of the magnetic composites on microstrip line were extracted by the 3D FEM simulation program of HFSS. The magnitudes of power absorptions were greatly enhanced up to 98% and broadened the absorbing frequency band over 5 GHz by the insertion of a conductive grid in magnetic composite. The initial frequency of the power absorption can controlled by the change of the ferromagnetic resonance frequencies of the magnetic composite.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.333-336
• /
• 2006

A new forming method for metal/ other metal two-layer tubes by multi-billet extrusion (MBE) is introduced. The forming possibilities of two-layer tubes CDA 365(inner)/Al 1100(outer) and Al 2014(inner)/Al 1100(outer) by MBE are investigated according to the given frictional condition and die profile. The results show that two-layer tube composed by two types tube as abovementioned can be manufactured by MBE. Some stated variables in the forming process such as effective stress and normalized pressure at welding surface are analyzed by FEM code ($DEFORM^{TM}$-3D)

• Transactions of Materials Processing
• /
• v.25 no.1
• /
• pp.56-60
• /
• 2016

Precise prediction and control of the strip profile is crucial for automatic process set-up and operation of a hot strip mill. In the current study, we present the effect of post-deformation on the steady-state strip profile. The process was simulated by a 3-D elastic-plastic finite element (FE) analysis. Comparisons are made between the strip profile measured at the roll exit and the steady-state strip profile. The results raised an issue with regard to the importance of taking into account the effect of post-deformation.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04a
• /
• pp.211-216
• /
• 1998

Parameter analysis of mass concrete structures of two types subjected to heat of hydration and surface heat transfer is presented. Thermal stress analysis is conducted through the 3D FEM program. Thermal and mechanical properties of concrete, for example, conductivity, heat capacity, density, thermal expansion coefficient are varied from 80% to 120% of a reference value, and the change of thermal stress against the parameter is achieved respectively. As a result of the analysis, the parameter affecting thermal stress most significantly is an adiabatic temperature rise in the case of wall-type structure, and an initial temperature of concrete in the case of slab-type structure, respectively.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.490-495
• /
• 2001

This paper deals with an analysis and countermeasure for improving the shock performance of laptop computers. The shock analysis is carried out by using the commercial program of LS-DYNA3D. Also the analysis is verified by the measurements from modal tests and shock tests. The available countermeasures are investigated theoretically and experimentally to find the effective methods of reducing the shock acceleration on hard disk driver during one side fall test. The hard disk drive is the most sensitive part in a laptop computer. This research shows the effects of the spring constant of rubber pad, the reinforcement of mechanical parts and the location of a hard disk driver, on the shock reduction.