• Journal of the Korean Society for Marine Environment & Energy
• /
• v.8 no.4
• /
• pp.186-192
• /
• 2005

We investigated the deposition characteristics and mass transport flux estimation of the Nakdong estuary, Korea. To understand the effects of the tidal current circulation that influences estuary terrain changes, we used a 2D numerical model to map seawater circulation under three different situations, with the level of river flow being set as none or flood. The net-water flux of the cross-sectional area between sandbars (known as dung) was estimated. From our review of previous research, we know that the development of local sandbars shifted from the west to the east side of the estuary after the construction of the Nakdong River dike. Current development is occurring mostly at the Bakhap-dung near Tadea. The seawater circulation pattern over this large-scale area of tidal na is brings changes related to the quantity of the outflow from the Nakdong River. Based on the calculated results for the net-water flux of the cross-sectional area, we see very strong accumulation in local waters around Jangjiado, Bakhapdung, and Tadae under flood river flow conditions, but accumulation in local waters around Jinudo under the other states of flow. Consequently, in the Nakdong estuary, the main sensitive regions that are affected by changes in the flow of river discharge are the local waters around Jangiado, Bakhapdung, Tadae, and Jinudo.

• Journal of IKEEE
• /
• v.23 no.1
• /
• pp.280-288
• /
• 2019

In the CR-enabled MANET, routing paths can be easily destroyed due to node mobility and channel unavailability (due to the emergence of the PU of a channel), resulting in significant overhead to maintain/recover the routing path. In this paper, network caching is actively used for route maintenance, taking into account the properties of the CR. In the proposed scheme, even if a node detects that a path becomes unavailable, it does not generate control messages to establish an alternative path. Instead, the node stores the packets in its local cache and 1) waits for a certain amount of time for the PU to disappear; 2) waits for a little longer while overhearing messages from other flow; 3) after that, the node applies local route recovery process or delay tolerant forwarding strategy. According to the simulation study using the OPNET simulator, it is shown that the proposed scheme successfully reduces the amount of control messages for path recovery and the service latency for the time-sensitive traffic by 13.8% and 45.4%, respectively, compared to the existing scheme. Nevertheless, the delivery ratio of the time-insensitive traffic is improved 14.5% in the proposed scheme.

• Applied Chemistry for Engineering
• /
• v.30 no.3
• /
• pp.384-388
• /
• 2019

In winter season, the snow and ice accretion on the bottom of the high speed railway rolling stock and boogie part has fallen at a high speed from the ballast section (gravel section for the transmission of the rolling stock load received by sleepers and fixing sleepers), causing the gravel to be scattered, thereby damaging the railway rolling stock structures and facilities. In order to solve these problems, the gravel scattering prevention net, manual de-icing, and movable hot air machine were used, but their efficiency was low. For the more efficient de-icing than ever before, an optimum material for de-icing fluid for high speed railway rolling stock was developed by evaluating the ice melting capacity, kinematic viscosity, evaporation of the material used as a chemical de-icing fluid. Four kinds of organic acid salts (sodium formate, sodium acetate, potassium formate and potassium acetate) and two different alcohols (propylene glycol, glycerol) were used as evaluation materials. Potassium formate, potassium acetate, and propylene glycol had similar ice melting capacities in the indoor test, but the propylene glycol showed the best ice melting capacity in spraying the system simulation test. This is because the kinematic viscosity of propylene glycol was 2.989029 St, which is higher than those of other materials therefore, it could stay longer on the ice and de-icing. In addition, potassium formate and potassium acetate were difficult to be used since the crystals precipitated and adversely affected the appearance of the rolling stock. The propylene glycol is the most optimum as an de-icing fluid for the high speed railway rolling stock.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.11
• /
• pp.5636-5645
• /
• 2013

The purpose of the study was to identify the relationship between emotional intelligence, ego resilience and stress in clinical practice of nursing students. The participants were 588 nursing students. The collected data were analyzed using descriptive statistics, t-test, ANOVA, and Pearson correlation coefficients. The mean scores for emotional intelligence 4.76(0.69), ego resilience 2.80(0.33), and stress in clinical practice 3.03(0.52) were above average. Emotional Intelligence was significantly different according to gender, satisfaction with nursing as a major, and satisfaction in clinical practice. Ego resilience was significantly different according to satisfaction with nursing as a major, satisfaction in clinical practice. Stress in clinical practice was significantly different according to gender, duration of clinical practice, satisfaction with nursing as a major, satisfaction in clinical practice, simulation practice, and main tutor in clinical practice. Significant correlations were found between emotional intelligence, ego resilience and stress in clinical practice. These findings indicate that there is a need to improve emotional intelligence and ego resilience to lessen stress in clinical practice of nursing students.

• Progress in Medical Physics
• /
• v.13 no.4
• /
• pp.202-208
• /
• 2002

The purpose of this study is to evaluate the monitor unit obtained from various methods for the treatment of superficial cancers using electron beams. Thirty-three breast cancer patients who were treated in our institution with 6, 9, and 12 MeV electron beams, were selected for this study. For each patient, irregularly shaped treatment blocks were drawn on simulation film and constructed. Using the irregular blocks, monitor units to deliver 100 cGy to the dose maximum (dmax) were calculated from measurement and three-dimensional radiation treatment planning (3D RTP) system (PINNACLE 6.0, ADAC Laboratories, Milpitas CA) Measurements were made in solid water phantom with plane parallel (PP) chamber (Roos, OTW Germany) at 100 cm source-to surface distances. CT data was used to investigate the effect of heterogeneity. Monitor units were calculated by overriding CT values with 1 g/㎤ and in the presence of heterogeneity. The monitor unit values obtained by the above methods were compared. The dose, obtained from measurement in solid water phantom was higher than that of RTP values for irregularly shaped blocks. The maximum differences between monitor unit calculated in flat water phantom at gantry zero position were 4% for 6 MeV and 2% for 9 and 12 MeV electrons. When CT data was used at a various gantry angle the agreement between the TPS data with and without density correction was within 3% for all energies. These results indicate that there are no significant difference in terms of monitor unit when density is corrected for the treatment of breast cancer patients with electrons.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.10
• /
• pp.33-41
• /
• 2000

Pyroelectric characteristics such as voltage responsivity, noise equivalent power and detectivity are modeled 3-dimensionaly considering th interaction of each parameters. Also, the circuit is designed to set up the frequency band width and the signal amplification of the pyroelectric IR sensor. The case of low frequency region shows that the voltage response increases with the independence of the sensor area as the thickness decreases. In the high frequency region, it is found that the voltage response with the load resistor of 20$G{\Omega}$ increases with the independence of the sensor thickness as the sensor area decreases. In the low frequency region, the detectivity becomes excellent at th load resistor of 20$G{\Omega}$, the sensor area larger than $4{\times}10^{-10}m^2$ and the sensor thickness thinner than $1{\times}10^{-5}m$, while, in the high frequency region, it shows high value at the sensor thickness thinner than $1{\times}10^{-5}m$ and the sensor area smaller than $2{\times}10^{-10}m^2$ with the independence of the load resistor. In the circuit design, quasi-boot-strap circuit is employed, in which a single op-amp is connected to the drain of JFFT. Desirable frequency band width, amplification rate and the remarkable drop of noise of about 56% from that of conventional circuits with double op-amps are obtained.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.480-480
• /
• 2008

Vacuum circuit breaker(VCB) is now emerging as an alternative of gas circuit breaker(GCB) which uses SF6 gas as insulating material whose dielectric strength is outstanding. But we have to reduce SF6 gas because SF6 gas is one of greenhouse gas and efforts to reduce greenhouse gas are now trend of the world. Therefore, we can say VCB is the optimal alternative of GCB because vacuum is environmentally friendly. The vacuum interrupter is the core part of VCB to interrupt arcing current. There are mainly two methods to extinguish arc. One is radial magnetic field (RMF) method and the other is axial magnetic field (AMF) method. We deals with RMF method in this paper. Compared with AMP, RMF arc quenching method has different principle to extinguish arc. In case of RMF method, pinch effect is much larger than AMF method. Because of pinch effect RMF type contact electrodes have the single large spot which is severly damaged and melted while AMF type contact electrodes have small and multiple spots which are slightly damaged and melted. To prevent contact electrode being damaged and melted from high temperature-arc, RMF method uses Lorentz force to move arc. In this paper we calculated and compared the arc driving force of two cases and we analyzed the force acting on each part of arc by means of commercial finite element method software Maxwell 3D. They have 3petals and we considered two cases. One is the case when fixed(upper) and movable(lower) contacts are in mirror arrangement (Case 1). The other is the case when one of two contacts (movable contact) is revolved at maximum angle as possible as it can be (Case 2). And at each case above, we analyzed arc driving force at two positions, position 1 is the closest to the center of contact and position 2 is near the edge of petal on fixed contact. As a result we could find that Case 2 generated stronger arc driving force than Case 1 at position 1. But at position 2 Case 1 generated stronger arc driving force than Case 2. This simulation method can contribute to optimizing spiral-type electrode designs in a view of arc driving force.

• Korean Journal of Optics and Photonics
• /
• v.31 no.2
• /
• pp.59-70
• /
• 2020

We discuss a modified numerical model based on the Monte Carlo radiative transfer (MCRT) method, i.e., the MCRT matrix method, for the analysis of atmospheric scattering effects in three-dimensional flash LIDAR systems. Based on the MCRT method, the radiative transfer function for a LIDAR signal is constructed in a form of a matrix, which corresponds to the characteristic response. Exploiting the superposition and convolution of the characteristic response matrices under the paraxial approximation, an extended computer simulation model of an overall flash LIDAR system is developed. The MCRT matrix method substantially reduces the number of tracking signals, which may grow excessively in the case of conventional Monte Carlo methods. Consequently, it can readily yield fast acquisition of the signal response under various scattering conditions and LIDAR-system configurations. Using the computational model based on the MCRT matrix method, we carry out numerical simulations of a three-dimensional flash LIDAR system operating under different atmospheric conditions, varying the scattering coefficient in terms of visible distance. We numerically analyze various phenomena caused by scattering effects in this system, such as degradation of the signal-to-noise ratio, glitches, and spatiotemporal spread and time delay of the LIDAR signals. The MCRT matrix method is expected to be very effective in analyzing a variety of LIDAR systems, including flash LIDAR systems for autonomous driving.

• Korean Journal of Optics and Photonics
• /
• v.27 no.3
• /
• pp.106-113
• /
• 2016

In this paper, we deal with the wavefront compensation capability of a silicon carbide (SiC) deformable mirror (DM) with 37 actuators for adaptive optics. The wavefront compensation capability of the SiC DM is predicted by computer simulation and examined by actual experiments with a closed-loop adaptive optics system consistsing of a light source, a phase plate, a SiC DM, a high speed Shack-Hartmann sensor, and a control computer. Distortion of wavefront is caused by the phase plate in the closed-loop adaptive optics system. The distorted wavefront has a peak-to-valley (PV) wavefront error of $0.3{\mu}m{\sim}0.9{\mu}m$ and root-mean-square (RMS) error of $0.06{\mu}m{\sim}0.25{\mu}m$. The high-speed Shack-Hartmann sensor measures the wavefront error of the distortion caused by the phase plate, and the SiC DM compensates for the distorted wavefront. The compensated wavefront has residual errors lower than $0.1{\mu}m$ PV and $0.03{\mu}m$ RMS. Consequently, we conclude that we can compensate for the distorted wavefront using the SiC DM in the closed-loop adaptive optics system with an operating frequency speed of 500 Hz.

• Journal of the Korea Society of Computer and Information
• /
• v.27 no.4
• /
• pp.79-88
• /
• 2022

In order to develop a bodice prototype suitable for obese women in their 20s, this study compared and analyzed a total of five pattern system methods, including prototype of France and Japan, one prototype for education in Korea and two prototype for industries in Korea. Through this, this study attempted to investigate the bodice pattern system suitable for the development of plus-size women's clothing. For the pattern drafting, pattern 1 was applied with the most body dimensions such as interscye fold front, interscye fold back, bust circumference, neck circumference, and waist back length, and pattern 2, pattern 4, and pattern 5 were made based on bust circumference and waist back length. As a result of the appearance evaluation, Pattern 3 was evaluated as the best pattern in all items except for the suitability of the center front length and the suitability of the side waist circumference position. However, it was evaluated as inappropriate in items such as the vertical side line, the suitability of the side waist circumference line position, the suitability of interscye fold back position and shape, and the suitability of the back shoulder dart position. Most of the pattern drafting methods are based on the size of the bust circumference, but other institutional methods are considered necessary when setting the neck circumference and shoulder length for 20s obesity women. In addition, it is also required to develop a method for setting the front center length due to abdominal protrusion.