• Geomechanics and Engineering
• /
• 제21권5호
• /
• pp.423-432
• /
• 2020

Hydraulic conductivity is one of the engineering properties of soil. This study focusses on the influence of cement content on the hydraulic conductivity of cemented sand, which is investigated based on the results from numerical analysis and laboratory testing. For numerical analysis the cemented samples were scanned using X-ray Computed Tomography (CT) while laboratory testing was carried out using a triaxial setup. Numerical analysis enables us to simulate flow through the sample and provides insight to the microstructure. It quantifies the pore volume, proportion of interconnected voids and pore size distribution in both cemented and uncemented samples, which could be computed only through empirical equations in case of laboratory testing. With reduction in global voids, the interconnecting voids within the samples also reduce with cement content. Gamma cumulative distribution function is used to predict the percentage of voids lesser than a given pore volume. Finally, the results obtained from both numerical analysis and laboratory testing are compared.

• Earthquakes and Structures
• /
• 제1권2호
• /
• pp.177-195
• /
• 2010

This paper presents an appraisal of four nonlinear static procedures (CSM, N2, MPA and ACSM) employed in seismic assessment of plan-irregular buildings. It uses a three storey reinforced concrete plan-irregular frame building exemplifying typical older constructions of the Mediterranean region in the early 1970s that was tested in full-scale under bi-directional pseudo-dynamic loading condition at JRC, Ispra. The adequacy and efficiency of the simplified analytical modelling assumptions adopted were verified. In addition, the appropriate variants of code-prescribed NSPs (CSM and N2) to be considered for subsequent evaluation were established. Subsequent parametric studies revealed that all such NSPs predicted reasonably well both global and local responses, having the benchmark values been determined through nonlinear dynamic analyses using a suit of seven ground motions applied with four different orientations. The ACSM, however, predicted responses that matched slightly better the median dynamic results.

• 지질공학
• /
• 제29권4호
• /
• pp.383-391
• /
• 2019

Bio-grouting based on microbial-induced calcite precipitation (MICP) is recently emerging as a novel and environmentally friendly technique for improvement of coarse-grained ground. To date, the mechanical behaviour of bio-grouted coarse-grained soil with different calcite contents and grain sizes still remains poorly understood. The primary objective of this study is to investigate the influence of calcite content on the mechanical properties of bio-grouted coarse-grained soil with different grain sizes. This is achieved through an integrated study of uniaxial loading experiments of bio-grouted coarse-grained soil, 3D digitization of the grains in conjunction with discrete element modelling (DEM). In the DEM model, aggregates were represented by clump logic based on the 3D morphology digitization of the typical coarse-grained aggregates while the CaCO₃ was represented by small-sized bonded particle model. The computed stress-strain relations and failure patterns of the bio-grouted coarse-grained soil were validated against the measured results. Both experimental and numerical investigation suggest that aggregate sizes and calcite content significantly influence the mechanical behaviour of bio-cemented aggregates. The strength of the bio-grouted coarse-grained soil increases linearly with calcite content, but decreases non-linearly with the increasing particle size for all calcite contents. The experimental-based DEM approach developed in this study also offers an optional avenue for the exploring of micro-mechanisms contributing to the mechanical response of bio-grouted coarse-grained soils.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2011년도 추계학술대회
• /
• pp.75-84
• /
• 2011

본 논문에서는 지하공간에 설치되는 지중구조물에 대한 내진해석에 관한 연구로 구조물의 거동특성과 내진설계방법의 종류에 따라 수치해석을 실시하였다. 이를 위해 현재 가장 많이 실무에 적용되고 있는 내진설계방법인 등가정적해석법과 응답변위법을 적용하고 정밀한 해석이 가능한 시간이력해석법에 의해 검증을 시행하였으며 구조물 내진해석은 3-D 모델링에 의해 구조물-지반 상호작용을 고려하고 국내의 콘크리트구조설계기준에 따라 수행하였다. 해석 결과 현재 실무에서 적용되고 있는 등가정적해석법과 응답변위법을 적용하는 경우 정밀한 동적해석법 보다 다소 크게 산정되어 실무적용에 문제가 없음을 확인 할 수 있었다.

• Computers and Concrete
• /
• 제25권4호
• /
• pp.355-367
• /
• 2020

This paper proposed a numerical investigation based on finite elements analysis (FEA) in order to study the punching shear behavior of reinforced concrete (RC) flat slabs using ABAQUS and SAP2000 programs. Firstly, the concrete and the steel reinforcements were modeled by hexahedral 3D solid and linear elements respectively, and the nonlinearity of the used materials was considered. In order to validate this model, experimental results considered in literature were compared with the proposed FE model. After validation, a parametric study was performed. The parameters include the slab thickness, the flexure reinforcement ratios and the axial membrane loads. Then, to reduce the time of FEA, a simplified modelling using 3D layered shell element and shear hinge concept was also induced. The effect of the footings settlement was studied using the proposed simplified nonlinear model as a case study. Results of numerical models showed that increase of the slab thickness by 185.7% enhanced the ultimate load by 439.1%, accompanied with a brittle punching failure. The punching failure occurred in one of the tested specimens when the tensile reinforcement ratio increased more than 0.65% and the punching capacity improved with increasing the horizontal flexural reinforcement; it decreased by 30% with the settlement of the outer footings.

• Nuclear Engineering and Technology
• /
• 제56권3호
• /
• pp.959-965
• /
• 2024

The High Temperature Test Unit (HTTU) was an experimental set-up to conduct separate and integral effects tests of the Pebble Bed Modular Reactor (PBMR) core. The annular core consisted of a randomly packed bed of uniform spheres. Natural convection tests using both nitrogen and helium, and forced convection tests using nitrogen, were conducted. The maximum material temperature achieved during forced convection testing was 1200 ℃. This paper presents the numerical analysis of the flow and temperature distribution for a forced convection test using 3D CFD as well as a 1D systems-CFD computer code. Several modelling approaches are possible, ranging from a fully explicit to a semi-implicit method that relies on correlations of their associated phenomena. For the comparison between codes, the analysis was performed using a porous media approach, where the conduction and radiative heat transfer were lumped together as an effective thermal conductivity and the convective heat transfer was correlated between the solid and gas phases. The results from both codes were validated against the experimental measurements. Favourable results were obtained, in particular by the systems-CFD code with minimal computational and time requirements.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2009년 춘계학술대회논문집
• /
• pp.19-19
• /
• 2009

Dynamic Stall is a flow phenomenon which occurs on the retreating side of helicopter rotor blades during forward flight. It also occurs on blades of stall regulated wind turbines under yawing conditions as well as during gust loads. Time scales occurring during this process are comparable on both helicopter and wind turbine blades. Dynamic Stall limits the speed of the helicopter and its manoeuvrability and limits the amount of power production of wind turbines. Extensive numerical as well as experimental investigations have been carried out recently to get detailed insight into the very complex flow structures of the Dynamic Stall process. Numerical codes have to be based on the full equations, i.e. the Navier-Stokes equations to cover the scope of the problems involved: Time dependent flow, unsteady flow separation, vortex development and shedding, compressibility effects, turbulence, transition and 3D-effects, etc. have to be taken into account. In addition to the numerical treatment of the Dynamic Stall problem suitable wind tunnel experiments are inevitable. Comparisons of experimental data with calculated results show us the state of the art and validity of the CFD-codes and the necessity to further improve calculation procedures. In the present paper the phenomenon of Dynamic Stall will be discussed first. This discussion is followed by comparisons of some recently obtained experimental and numerical results for an oscillating helicopter airfoil under Dynamic Stall conditions. From the knowledge base of the Dynamic Stall Problems, the next step can be envisaged: to control Dynamic Stall. The present discussion will address two different Dynamic Stall control methodologies: the Nose-Droop concept and the application of Leading Edge Vortex Generators (LEVoG's) as examples of active and passive control devices. It will be shown that experimental results are available but CFD-data are only of limited comparison. A lot of future work has to be done in CFD-code development to fill this gap. Here mainly 3D-effects as well as improvements of both turbulence and transition modelling are of major concern.

• 한국지반공학회논문집
• /
• 제18권1호
• /
• pp.17-28
• /
• 2002

터널의 막장부근에서는 하중전이가 복잡한 3차원적 거동특성을 나타낸다. 일반적으로 3차원 해석은 입력자료의 준비 및 결과 해석에 많은 노력을 요하며, 비선형 압밀해석을 수행하는 경우 컴퓨터 계산수요가 커지는 문제 때문에 실제설계는 2차원 해석법을 주로 사용하게 된다. 3차원적인 터널거동을 2차원적으로 모델링하기 위하여는 터널 굴진과정을 수치해석적으로 표현하기 위한 경험 파라미터가 요구되며, 해석결과는 이 파라미터 값에 따라 크게 변화하는 특성을 나타낸다. 특히 이 값의 평가는 주로 주관적이고 경험적인 판단에 의존하게 되므로 임의성이 커 해석의 신뢰성 문제를 야기할 수 있다. 특히 지반거동이 간극수 등 시간의존성 요인에 의해 영향을 받는 경우 이 파라미터를 평가하기는 더욱 어려워진다. 본 논문에서는 이러한 문제점을 개선하기 위하여 제안된 Time-based 2-D Modeling Method를 사용하여 지하수위가 높은 풍화화강토내 터널굴착 문제에 적용하였고 이를 분할 굴착에도 적용 가능하도록 확장하였다. 해석결과는 실측결과와 잘 일치하는 거동을 보였다. 이 방법을 이용하여 복합막장터널의 거동특성을 조사한 결과, 마제형 터널단면의 역학적 유익성이 확인되었다.

• 한국터널지하공간학회 논문집
• /
• 제22권1호
• /
• pp.23-46
• /
• 2020

본 연구에서는 터널 근접 시공으로 인한 기 존재 단독말뚝의 공학적 거동을 파악하기 위하여 터널로부터 말뚝선단의 이격거리와 막장압의 변화를 고려한 3차원 유한요소해석을 수행하였다. 수치해석에서는 터널 막장압을 고려하여 말뚝의 거동을 분석하였으며, 터널굴착으로 유발되는 지반침하, 말뚝두부침하, 말뚝축력 및 말뚝-지반 사이의 경계면에서 발생하는 전단응력을 고찰하였다. 말뚝이 터널 크라운(crown) 바로 상부에 위치하고 말뚝선단까지의 수직 이격거리가 0.25D (여기서, D는 터널직경)인 경우 초기 응력의 50%에 해당하는 막장압을 적용할 경우 25%의 막장압을 적용한 것과 비교한 결과 말뚝두부의 침하가 약 38% 감소하였다. 또한, 막장압의 크기가 작을수록 지반침하, 말뚝의 축력 및 말뚝-지반 사이에서 발생하는 전단응력이 증가하며, 말뚝이 터널굴착 영향권 밖에 존재할 경우 말뚝에는 압축력 형태의 축력이 발생하였다. 따라서 막장압의 크기 및 터널-말뚝선단의 상대위치는 지반 침하와 말뚝 침하에 큰 영향을 미치는 것으로 분석되었다. 본 연구에서 수행된 연구결과의 경우 기존에 보고된 연구결과를 바탕으로 비교분석을 실시하였으며, 터널굴착으로 인한 말뚝의 거동을 심도 있게 분석하였다.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제22권3호
• /
• pp.1-9
• /
• 2017

The numerical analysis of groundwater flow is indispensable for predicting problems associated with water resource development, civil works, environmental hazards, and nuclear power plant construction. Korea lacks public regulatory procedures and guidelines for groundwater flow modeling, especially in nuclear facility sites, which makes adequate evaluation difficult. Feasible step-by-step guidelines are also unavailable. Consequently, reports on groundwater flow modeling have low-grade quality and often present controversial opinions. Additionally, without public guidelines, maintaining consistency in reviewing reports and enforcing laws is more challenging. In this study, the guidelines for groundwater flow modeling were reviewed for three countries - the United States (Documenting Groundwater Modeling at Sites Contaminated with Radioactive Substances), Canada (Guidelines for Groundwater Modelling to Assess Impacts of Proposed Natural Resource Development Activities), and Australia (Australian Groundwater Modelling Guidelines), with the aim of developing groundwater flow modeling regulatory guidelines that can be applied to nuclear facilities in Korea, in accordance with the Groundwater Act, Environmental Impact Assessment Act, and the Nuclear Safety Act.