• 한국정밀공학회지
• /
• 제33권5호
• /
• pp.333-339
• /
• 2016

In this paper, a fundamental experiment regarding the formation of porous 3D structures for personal safety products using 3D PPP (Porous Polymer Printing) was introduced for the first time. The filament was manufactured by mixing PP (Polypropylene) and CBA (Chemical Blowing Agent) with polymer extruder, and the diameter of the filament was approximately 1.75mm. The proposed 3D PPP method, combined with the conventional FDM (Fused Deposition Modeling) procedure, was influenced by process parameters, such as the nozzle temperature, printing speed and CBA density. In order to verify the best processing conditions, the depositing parameters were experimentally investigated for the porous polymer structure. These results provide parameters under which to form a multiple of 3D porous polymer structures, as well as various other 3D structures, and help to improve the mechanical shock absorption for personal safety products.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 A
• /
• pp.164-166
• /
• 1998

This paper presents the results of the measured pressure-rise and the analyzed results of the cold gas flow-field in a 72.5kV 20kA gas circuit breaker for the electrical railway system. The analysis of cold gas flow field and the calculation of electric field strength have been performed in 3 types of interrupters and the low current interruption capability has been estimated for each of the gas circuit breaker considering the opening speed, the nozzle shape and the stroke length.

• 한국분무공학회지
• /
• 제25권1호
• /
• pp.8-14
• /
• 2020

Recently, 1-D model-based engine development using virtual engine system is getting more attention than experimental-based engine development due to the advantages in time and cost. Injection rate profile is the one of the main parameters that determine the start and end of combustion. Therefore, it is essential to set up a sophisticated model to accurately predict the injection rate as starting point of virtual engine system. In this research, procedure of 1-D model setup based on AMESim is introduced to predict the dynamic behavior and injection rate of diesel injector. As a first step, detailed 3D cross-sectional drawing of the injector was achieved, which can be done with help of precision measurement system. Then an approximate AMESim model was provided based on the 3D drawing, which is composed of three part such as solenoid part, control chamber part and needle and nozzle orifice part. However, validation results in terms of total injection quantity showed some errors over the acceptable level. Therefore, experimental work including needle movement visualization, solenoid part analysis and flow characteristics of injector part was performed together to provide more accuracy of 1-D model. Finally, 1-D model with the accuracy of less than 10% of error compared with experimental result in terms of injection quantity and injection rate shape under normal temperature and single injection condition was established. Further work considering fuel temperature and multiple injection will be performed.

• Carbon letters
• /
• 제4권4호
• /
• pp.168-174
• /
• 2003

Silver nitrate ($AgNO_3$) powder was mixed into a reformed pitch precursor. Then, the silver-containing pitch was melt spun to form round and "C" shape fibers. A wire mesh was inserted prior to the nozzle to improve the spinnability of the silvercontaining precursor pitch. Silver particles in the carbon fibers (CFs) were detected by XRD and TEM. These tests showed that silver particles were uniformly distributed and the total amount of silver remained constant during stabilization and carbonization. Next, the silver-containing CFs were activated by steam diluted in nitrogen gas. Silver particles accelerated the activation rate, but the specific surface areas of the silver-containing ACFs were similar to those of non-silver containing ACFs at the same burn-off levels. The specific surface area of the C-shaped activated carbon fibers was larger than that of the round activated carbon fibers. The likely reason is that the surface area of a C-shaped CF is about two times larger than that of a round CF when equivalent cross-sectional areas are compared. A small amount of silver particles in the periphery of the CFs was removed during the activation, but the remainder of silver was stayed within the ACFs.

• 한국산학기술학회논문지
• /
• 제16권2호
• /
• pp.1571-1578
• /
• 2015

전산유체역학(CFD)을 이용하여 산업체에 널리 적용되고 있는 충격기류형 탈진시스템의 탈진 특성을 규명하고, 그 성능을 향상시키기 위해 탈진부 유니트(unit) 형상을 개조한 경우의 탈진 성능을 비교하였다. 탈진부 각 형상에 대해 검토한 결과, 블로우 튜브에 노즐을 설치한 경우(Case 3)와 벤츄리에 이중 유입관을 설치한 경우(Case4, 5)가 현재 현장에서 널리 적용되고 있는 구조(Case 1)에 비해 우수한 것으로 예측되었다. 또한 최적 형상의 벤츄리를 설계하고, 이 벤츄리를 pilot plant에서 실험하여 현장 적용성을 분석하였다. 블로우 튜브와 본 연구에서 제안한 벤츄리를 조합한 시스템의 경우, 기존 시스템(블로 튜브만 사용한 경우와 블로 튜브와 벤츄리를 조합한 경우)에 비해 탈진 기류를 집중시키는데 매우 효과적인 것으로 나타났다. 또한 본 연구에서 제안한 벤츄리를 장착하여 테스트한 결과, 산업 현장에서 사용 중인 상용 벤츄리를 사용한 경우 보다 탈진횟수 및 탈진시간이 많이 향상되는 결과를 보였다.

• 한국항공우주학회지
• /
• 제31권2호
• /
• pp.1-9
• /
• 2003

본 연구에서는 비정렬 격자를 이용한 병렬화된 3차원 직접모사법을 개발하였다. 모사 입자의 추적에는 선형 형상 함수를 3차원으로 확장하여 적용하였다. 프로그램에서는 효율적인 병렬계산을 위하여 모사 입자의 수에 기초한 영역 재분할 방식을 이용하여 프로세서간의 작업 균형을 유지하였다. 밀도 차가 큰 두 개 이상의 유동이 동시에 존재할 경우를 효과적으로 모사하기 위해서 입자에 가중치를 적용하는 기법을 도입하였다. 프로그램의 검증을 위해서 3차원 삼각 날개 유동을 해석하여 실험치나 다른 계산 결과와 비교하였다. 또한 고도 100km의 희박한 환경헤서 우주발사체 탑재부 주의 유동을 해석하여 노즐 전방으로 고온의 풀룸이 역류하여 비행체 표면에 영향을 미칠 수 있는 가능성을 타진하였다.

• 대한기계학회논문집
• /
• 제9권6호
• /
• pp.732-742
• /
• 1985

본 논문에서는 이 2차원 재부착분류(본문에서는 stepped wall jet라 명명함) 유동장을 재부착상류 부분, 재부착점 근방, 재부착 이후의 재발전 벽면분류 지역의 세 영역으로 구분하여 재부착 길이, 평균속도, 벽면정압을 측정하고 on-line에 의한 디지 틀 데이터 처리기법을 이용하여 난류강도, 레이놀즈 전단응력, 속도의 3승적(triple velocity product), integral length scale, Taylor's microscale 등을 실험적으로 구 하여 재부착 상류 부분에서는 자유분류와 비교하고, 재부착 이후에서는 2차원 벽면분 류와 비교하기로 한다.그리하여 초기 교란을 받는 분류가 벽면에 재부착하여 2차원 벽면분류로 재발전되어 가는 과정에 있어서의 평균 유동장과 급격한 변화를 갖는 난류 특성을 상세히 조사하여, 보다 일반적으로 적용될 수 있는 난류모델을 개발함에 있어 서 실험적인 자료를 제공하고자 한다. Fig. 1은 본 실험의 유동장에 대한 개약도를 보여주고 있다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.789-794
• /
• 2000

The Paper studies the flow and heat transfer characteristics to a jet impinging at different oblique angles, to a plane surface by numerical methods. The flowfield and heat transfer rate associated with the oblique Impingement of an axisymmetric jet are of interest as a result of its presence in numerous technological Problems. For the computation of heat transfer rate, the standard ${\kappa}-{\varepsilon}$ and ${\kappa}-{\varepsilon}-\bar {{\upsilon}'^ 2}$ turbulent model were adapted. The accuracy of the numerical calculations was compared with various experimental data reported in the literature. ${\kappa}-{\varepsilon}-\bar {{\upsilon}'^ 2}$ model showed better agreement with experimental data than standard ${\kappa}-{\varepsilon}$ model in prediction of the turbulent intensity and the heat transfer rate. In the case of computation of flowfield, the study carries on the ${\alpha}=45$ deg, h/D=4.95. The jet Reynolds number based on the nozzle diameter(D), was 48,000. For the computation of heat transfer rate, the Re=20,000, the jet orifice-to-plate spacings(L/D) are 4, 6 and 10, and the angle between the axis of the jet orifice and the plate surface is set at 30, 45, 60, or 90 deg. For the smaller spacings, the near-peak Nusselt numbers are not significantly effected by the initial decreases in the Jet angle. The overall shape of the local Nusselt number x-axis profile is influenced by both the jet orifice-to-plate spacing and the jet angle.

• 설비공학논문집
• /
• 제10권3호
• /
• pp.324-333
• /
• 1998

Measurements of the local heat transfer coefficients on a hemispherically concave surface with a round oblique impinging jet were made. The liquid crystal transient method was used for these measurements. This method, which is a variation of the transient method, suddenly exposes a preheated wall to an impinging jet while video recording the response of liquid crystal for the surface temperature measurements. The Reynolds number used was 23,000 and the nozzle -to -jet distance was L/d=2, 4, 6, 8 and 10 and the jet angle was $\alpha$=0$^{\circ}$, 15$^{\circ}$, 30$^{\circ}$and 40$^{\circ}$. In the experiment, the maximum Nusselt number at all region occurred at L/d(equation omitted)6 and Nusselt number decreases as the inclined jet angle increases. For the normal jet the contours of constant Nusselt number are circular and as the jet is inclined closer and closer to the surface the contours become elliptical shape. The decreasing rate of the Nusselt number at X/d＞ 0(upstream) on a surface curvature are higher than those on a flate plate and the decreasing rate of the Nusselt number at X/d ＜0(downstream) on a surface curvature are lower than those on a flate plate. And also, the decreasing rate of local Nusselt number distribution at X/d ＜0(upstream) exhibit lower than with X/d ＜0(downstream) as jet angle increases. The second maximum Nusselt number occurred at long distance from stagnation point as jet angle increases.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 봄 학술논문 발표대회
• /
• pp.91-92
• /
• 2023

With the development of technology, interest in the implementation of free-form buildings is increasing, and research on producing free-form panels is being conducted accordingly. Since free-form buildings are curved and consist of geometric shapes, there are many problems with the production technology of free-form panels that implement them. Due to the inability to reuse molds, the cost of disposal of construction waste and waste of manpower for assembly increase the construction period and construction cost. To improve these limitations, a 3D printed concrete nozzle for FCP production was developed. However, this technology is not quantitatively extruded according to the shape of the panel, and there is a problem that residues are generated. Therefore, an free-form panel extrusion experiment was conducted to analyze the limitations of existing nozzles and to analyze the requirements for the development of new concrete extrusion nozzles. Existing nozzles were unable to be quantitatively extruded, resulting in errors. Due to the weak pressure of the screw and the inability to adjust the internal pressure, detailed extrusion speed control was impossible, and residue generation in the opening and closing device seemed to be the cause. Therefore, a pump capable of quantitative concrete pressure transfer and a pressure control device for easy extrusion of concrete are required. In addition, it is judged that it is necessary to develop an opening and closing device and an extrusion device that do not generate residues. The results of this study are expected to provide information for FCP production and production and to be a basic study of technologies necessary for the production of free-form building panels.