• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.7
• /
• pp.61-67
• /
• 2009

This paper reports an Integer-N phase locked loop (PLL) frequency synthesizer which was implemented in a 250nm standard digital CMOS process for a UHF RFID wireless communication system. The main blocks of PLL have been designed including voltage controlled oscillator, phase frequency detector, and charge pump. The LC VCO has been used for a better noise property and low-power design. The source and drain juntions of PMOS transistors are used as the varactor diodes. The ADF4111 of Analog Device has been used for the external pre-scaler and N-divider to divide VCO frequency and a third order RC filter is designed for the loop filter. The measured results show that the RF output power is -13dBm with 50$\Omega$ load, the phase noise is -91.33dBc/Hz at 100KHz offset frequency, and the maximum lock-in time is less than 600us from 930MHz to 970MHz.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.11
• /
• pp.1349-1355
• /
• 2016

It should guarantee high reliability and ultra low latency communication. Additionally, it should support connection between massive devices. As one of estimated scenarios for 5G mobile communication, mobile devices and sensors using low data rate wireless communication will increase. For communication of these devices, single-carrier system can be considered. In order to satisfy these requirements, in this paper, we propose CDMA (Code Division Multiple Access) system using complex spreading and Multi-level BPSK(Binary Phase Shift Keying). The proposed system spread transmit symbol by using chip code consisted of real and imaginary number. As simulation results, we can confirm that although the proposed system has 3dB lower BER (Bit Error Rate) performance than conventional CDMA system, the proposed system can support 2 times more users in comparison with conventional CDMA system.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.4
• /
• pp.41-48
• /
• 2022

This study is a study that designed in-building antennas with improved orientation to improve 5G quality in buildings as 5G is stabilized and more and more traffic is expected to occur in buildings. Instead of applying the forward arrangement of antenna elements, which is the Yagi antenna propagation orientation principle, the antenna design method of vertical arrangement applied to the base station antenna was proposed, and it was confirmed through experiments that antenna orientation increased. According to the experimental results, the directivity did not increase significantly within 10m of the separation distance from the antenna, but the directivity increased by about 3dB at the distance separated by more than 10m. Considering that the wireless environment in the building has various variables such as structure of internal structure, materials such as concrete and glass, closed space, and walls, it is expected that antenna with improved orientation can expand the scope of 5G quality improvement and maintain stable communication service in the building.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.3
• /
• pp.29-38
• /
• 1999

Software defined radio(SDR) si an emerging communication system technology, which is expected to be a solution for future-proof, flexible and inter-operable wireless services in military communications. In this paper, we investigate two major SDR research projects for military applications, SPEAKeasy and GloMo. We also provide the perspective of the future military SDR research.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.5A
• /
• pp.846-854
• /
• 2001

본 논문에서는 무선통신로 채널상에 존재하는 가우스 잡음을 포함한 협대역 A급 임펄스 잡음과 나카가미 페이딩 환경에서 하이브리드 DS/FH-CDMA MFSK 시스템의 성능을 비교 분석하고, 성능 개선 기법으로 MRC 다이버시티 수신 기법과 부호화 기법을 동시에 채용함으로써 고려되어진 시스템의 성능을 개선시켰다. 결과에 의하면 임펄스 지수가 강할수록 또한, 페이딩 지수가 작을수록 하이브리드 DS/FH-CDMA 시스템에서는 성능이 더욱 열화됨을 알 수 있었고, 성능 개선 기법으로 BCH 부호화 기법을 채용했을 경우 페이딩 지수가 증가할수록 성능개선의 폭이 큼을 알 수 있었다. 페이딩 지수가 작은 열악한 환경에서는 MRC 다이버시티 수신 기법을 채용하였을 경우 시스템 성능이 우수하였지만, 페이딩 영향이 감소할수록 BCH 부호화 기법을 채용하였을 경우 시스템 성능이 우수함을 알 수 있었다. 또한, 레일리 페이딩 환경에서 각각의 성능개선 기법을 단독으로 채용하였을 경우, 음성서비스 품질($10^{-3}$)에 도달할 수 없지만, BCH 부호화 기법과 MRC 다이버시티를 동시에 채용함으로써 강한 임펄스 잡음 하에서도 24dB 이상에서 음성서비스 기준 오율을 만족하는 성능 개선 효과를 얻을 수 있었고, 페이딩 지수가( $m_{i}$=3) 이상에서는 강한 임펄스 잡음이 부가되어도 21dB에서 $10^{-3}$을 만족하고 28dB 이상에서는 데이터 서비스 기준($10^{-5}$) 오율을 만족하는 우수한 성능 개선 효과를 보임으로써 다이버시티 가지수와 부호화의 이득에 의한 에러 성능이 향상되었다.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.2
• /
• pp.71-76
• /
• 2006

With the rapid development of spatial infrastructure in US, Europe, Japan, China and India, there is no doubt that the next generation Global Navigation Satellite System (GNSS) will improve the integrity, accuracy, reliability and availability of the position solution. GNSS is becoming an essential element of personal, commercial and public infrastructure and consequently part of our daily lives. However, the applicability of GPS in supporting a range of location-sensitive applications such as location based services in an urban environment is severely curtailed by the interference of the 3D urban settings. To characterize and gain in-depth understanding of such interferences and to be able to provide location-based optimization alternatives, a high-fidelity 3D urban model of Melbourne CBD built with ArcGIS and large scale high-resolution spatial data sets is used in this study to support a comprehensive simulation of current and future GNSS signal performance, in terms of signal continuity, availability, strength, geometry, positioning accuracy and reliability based on a number of scenarios. The design, structure and major components of the simulator are outlined. Useful time-stamped spatial patterns of the signal performance over the experimental urban area have been revealed which are valuable for supporting location based services applications, such as emergency responses, the optimization of wireless communication infrastructures and vehicle navigation services.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.6
• /
• pp.1129-1136
• /
• 2022

This study leads to the shortcoming that the RSSI distance measurement method is easily affected by the external environment and the position error is large, leading to the problem of optimizing the distance values measured by the RSSI distance measurement nodes in this three-dimensional configuration environment. We proposed the CA-PSO-BP algorithm, which is an improved version of the CA-PSO algorithm. The proposed algorithm allows setting unknown nodes in WSN 3D space. In addition, since CA-PSO was applied to the BP neural network, it was possible to shorten the learning time of the BP network and improve the convergence speed of the algorithm through learning. Through the algorithm proposed in this study, it was proved that the precision of the network location can be increased significantly (15%), and significant results were obtained.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.3
• /
• pp.317-329
• /
• 1998

In this paper, we have analyzed the packet error probability of DS/CDMA-Trellis Coded QPSK modulation signal with MRC(Maximum Ratio Combining) diversity reception in Rician fading, multi-user interferences and multipath channel. And then we have evaluated the performance and capacity of DS/CDMA-Trellis Coded QPSK system using the MRC diversity reception as a function of direct power to indirect power ratio ($K_R$), the number of diversity branch(M), the number of multi-user(U), PN chip rate(PN), the number of multipath channel($L_P$), and packet length(PL). From the results, we know that the coding gain of DS/CDMA-Trellis Coded QPSK system with 2 branch MRC diversity is about 6 dB against uncoded DS/CDMA BPSK system with 2 branch MRC diversity in Rician fading ($K_R=6dB), 5 multi-user interferences, and 3 multipath channel. And, we know that coded QPSK signal designed for the AWGN channel also perform well on a Rician fading channel with MRC diversity reception. Consequently, we expected that proposed system structure is reliable to the wireless data communication system in Rician fading, multi-user interferences, and multipath channel.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.6
• /
• pp.923-931
• /
• 2013

RFID (Radio Frequency Identification), which is a kind of the electronic tag, is a wireless access device using the radio frequency for recognizing the ID information. It has a variety of application such as the bus card, gate access card, distribution industry, and management of construction materials. The performance and size of RFID depend on the penetrability, recognition ratio, memory size, multi tag recognition, external pollution dust, and exterior impact, and RFID requires the packaging to protect itself considered above factors. Recently, RFID is diversely employed to effectively manage construction materials and the RFID packaging, which is robust to the external impact, is required to attach RFID on construction materials. In this paper, we propose the construction material RFID packaging designed to be robust for the external impact and to be practicable for change of the broken RFID. For the change of RFID, we separate the cast and body of the packaging. Also, we present the detail drawing for the proposed construction material RFID packaging and implement the performance evaluation of the packaging manufactured using 3D printer.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.1
• /
• pp.203-209
• /
• 2019

In this work, a new land-specific resistance measuring device (GM) and a measuring probe (Grounding Rod) are connected to the WENNER quadrant as power-line communication (PLC). In groups of two (P1,P2) probes, five to ten probes are installed in series on the ground at intervals of 1m, 2m, 4m, 8m, and 16m, respectively. If the PLC signal from the GMD is detected by the receiver of the Probe 1 (P1) for measurement, the minute voltage and current for measurement flow from the PSD (power supply) attached to the probe to the ground, and then, through the soil between P1 and P2, enters the Probe 1 (P2). The resistance value is then measured by the principle of voltage drop due to ground resistance. Measure the earth resistance every T seconds up to 1 trillion and store the measured data on the Arduino Server mounted on the main equipment. Stored measurement data can be derived from formulas by Ohm's Law and from inherent resistance (here,). Data obtained in real time will be linked to CDGES programs installed on Main PC, enabling data analysis and real-time monitoring of the ground environment on land. In addition, a three-dimensional display is possible with 3D graph support by identifying seasonal characteristics such as temperature and humidity of land (soils). The limitations of the study will require specific application measures of Test Bed for commercial access to a model that has been developed and operated experimentally.