• JSTS:Journal of Semiconductor Technology and Science
• /
• 제8권4호
• /
• pp.295-301
• /
• 2008

Recently, the demand on mm-wave (millimeter-wave) applications has increased dramatically. While circuits operating in the mm-wave frequency band have been traditionally implemented in III-V or SiGe technologies, recent advances in Si MOSFET operation speed enabled mm-wave circuits realized in a Si CMOS technology. In this work, a 58 GHz CMOS LC cross-coupled VCO (Voltage Controlled Oscillator) was fabricated in a $0.13-{\mu}m$ Si RF CMOS technology. In the course of the circuit design, active device models were modified for improved accuracy in the mm-wave range and EM (electromagnetic) simulation was heavily employed for passive device performance predicttion and interconnection parasitic extraction. The measured operating frequency ranged from 56.5 to 58.5 GHz with a tuning voltage swept from 0 to 2.3 V. The minimum phase noise of -96 dBc/Hz at 5 MHz offset was achieved. The output power varied around -20 dBm over the measured tuning range. The circuit drew current (including buffer current) of 10 mA from 1.5 V supply voltage. The FOM (Figure-Of-Merit) was estimated to be -165.5 dBc/Hz.

• 한국전자파학회논문지
• /
• 제10권5호
• /
• pp.766-776
• /
• 1999

본 논문에서는 실내 전파 환경에서의 편파 다이버시티와 공간 다이버시티의 성능을 분석하기 위하여 영상 법을 기본으로 한 3차원 광선 추적법을 이용하였다. 본 모텔링은 선호강도 뿐만 아니라 채널의 페이딩 특성 을 예측할 수 있기 때문에 편파 및 공간 다이버시티 기법의 성능을 분석하는데 이용될 수 있다. 측정과 시율 레이션 결과로부터 편파 및 공간 다이버시티가 실내 무선 통선 채널의 성능을 향상시킬 수 있음을 확인하였 고, 특히 지향성 안테나를 이용한 편파 다이버시티를 제안하여 기존의 다이폴 안테나를 이용하는 다이버시티 기볍보다 우수한 성능을 가짐을 보였다.

• 한국전자파학회논문지
• /
• 제18권5호
• /
• pp.539-546
• /
• 2007

본 논문에서는 온-칩 스파이럴 인덕터 해석에 대한 3차원 전자장 시뮬레이션 방법을 제시하였으며, 이 방법은 정확히 예측 가능한 CMOS VCO를 설계하는데 적용될 수 있음을 보였다. VCO는 CMOS 0.25 um 표준 공정을 이용하여 LC-공진형으로 구현하였으며, 공진기의 스파이럴 인덕터는 실리콘 기판과의 사이에 그라운드 패턴을 삽입한 경우와 그렇지 않은 경우에 대해 각각 VCO를 구현하여 인덕터의 Q값 개선에 의해 VCO의 위상 잡음이 어느 정도 개선되는지를 검증하였다. 제작된 VCO는 2.5 V 제어 전압에서 3.094 GHz, -12.15 dBm 출력을 가지며, LC 공진에 사용된 단일 인덕터의 Q는 그라운드 패턴을 삽입한 경우 3 GHz에서 8% 정도 개선됨을 시뮬레이션을 통해 검증하였으며, 이로 인한 위상 잡음은 3 MHz 오프셋 주파수에서 9 dB 개선되어짐을 실험을 통해 확인하였다.

• 한국전기전자재료학회논문지
• /
• 제17권5호
• /
• pp.552-559
• /
• 2004

In recent, there have been several developments in lamp technology that promise savings in electrical power consumption and improved quality of the lighting space. Above all, the advantage of ring-shaped electrodeless fluorescent lamp is the removal of internal electrodes and heating filaments that are a light-limiting factor of conventional fluorescent lamps. The ring-shaped electrodeless lamp is intended as a high efficiency replacement for the incandescent reflector lamp in many applications. Therefore, the life time of ring-shaped electrodeless fluorescent lamps is substantially higher than that of conventional fluorescent lamps and last up to 60,000 hours. In this paper, maxwell 3D finite element analysis program(Ansoft) was used to obtain electromagnetic properties associated with the coil and nearby structures. The electromagnetic emitting properties were presented by 3D simulation software operated at 250 KHz and some specific conditions. The optical characteristics were measured luminance and a temperature and an optical spectrum distribution for 10 min in a one minute interval at the same time. With a goal of finding alternative materials, we show measurement results of electrical characteristics of a ring-shaped electrodeless fluorescent lamp as a function of frequency and the number of coil turns using a highly permeable($\mu$$_{r}$(equation omitted) 2,000) Mn-Zn ferrite. These results are compared with those of conventional ring-shaped electrodeless fluorescent lamp. It is found that the resistance, inductance and impedance are increased while the quality factor decreases as frequency increases.s.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2003년도 종합학술발표회 논문집 Vol.13 No.1
• /
• pp.91-95
• /
• 2003

In this work, we have designed Gilbert cell downconversion mixer using 0.25um Anam CMOS process, we also have analyzed Conversion gain and IIP3 using Taylor series in our own unique way. Especially, bulk terminal is used as LO( Local Oscillator) input for reduction of power consumption and supply voltage. Supply voltage used in this design is lower than 1.8V and core current is less than 500uA. The simulation experiments showed that the conversion gain, IIP3, and power consumption were -1dB, 4.46dBm, and 0.8mW, respectively.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2003년도 종합학술발표회 논문집 Vol.13 No.1
• /
• pp.506-510
• /
• 2003

In this paper, a meander-line chip antenna with stacked layer is suggested, designed and fabricated employing the LTCC(Low Temperature Co-fired Ceramic) fabrication techniques. To reduce the antenna chip size, the meander-line antenna strip is distributed over three layer. Layers one interconnected using via holes. A 2.4 GHz chip antenna with size of $3.75{\times}7.9{\times}1.0 mm^3$ is designed and fabricated using the LTCC technique. Measurements of the fabricated antenna show 160 MHz bandwidth and 3.75 dBi maximum gain. The Measured reflection coefficient and radiation patterns agree well with the prediction by electromagnetic simulation.

• 한국전자파학회논문지
• /
• 제26권3호
• /
• pp.268-275
• /
• 2015

본 논문에서는 명료하고 간단한 초광대역 마이크로스트립-CPS(coplanar stripline) 전이구조 설계를 제안하였다. 등각사상을 이용하여 전이구조의 특성 임피던스를 해석을 하였으며, 닫힌 형태의 전이구조 공식을 제시하였다. 제안한 전이구조 공식의 계산 결과를 EM 상용 시뮬레이터와 비교하여 3.2 % 오차 이내임을 알 수 있었다. 초광대역 전이구조는 Klopfenstein 테이퍼를 이용하여, 광대역 임피던스 정합하였다. 제작된 전이구조는 5.39~40 GHz 이상의 대역에서 삽입손실 1 dB 이하 및 반사손실 10 dB 이상을 만족하였다.

• Journal of Magnetics
• /
• 제21권3호
• /
• pp.322-329
• /
• 2016

In this paper, we propose an array sensing detection method for smelting of submerged arc furnaces (SAF) based on electromagnetic radiation. AC magnetic field generated by electrode currents and molten currents in the furnace is reflected outside of the furnace. According to the spatial distribution of electromagnetic field a radiation model of SAF is built. We design a 3D magnetic field sensing array system in order to collect the magnetic field information. Through the collected information, the current distribution characteristics of SAF are described and the key parameters of smelting are obtained. Theoretical simulation and field test show that the curves acquired by the sensing array can accurately reflect the information of the relative displacement when the relative displacement between the array and electrode is 10 cm. Compared with the detection method of 3D single point, the proposed array sensing method of magnetic field obtains better results in terms of real-time and accuracy, and has good practical value for industrial measurement.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.936-939
• /
• 2006

The pneumatic isolator is widely adopted for anti-vibration of precision measuring and manufacturing equipments. But, when the precision demand on anti-vibration is extreme or the load is moving, the performance of anti-vibration can not meet satisfaction. In these cases, as a complementary, active vibration suppression system can be added for advanced performance. In this paper, an active control system is presented, which uses electromagnetic actuators for vibration suppression. The anti-vibration characteristic of pneumatic isolator is analyzed for system modeling and actuator specifying. The modeling and the 3D dynamic simulation is performed for control system design. For the electromagnetic actuator design, the magnetic flex density and the current-force characteristic analysis are achieved.

• 한국전자파학회논문지
• /
• 제14권9호
• /
• pp.912-918
• /
• 2003

본 논문에서는 셀룰러 CDMA와 IMT-2000 중계기 에 사용되는 이중대역 모노폴 안테나를 설계 및 구현하였다.3차원 전산모의실험 프로그램인 HFSS(High Frequency Structure Simulator)를 사용하여 안테나론 설계하였으며, 전기적 특성 측정은 HP 8720C네트웍 분석기론 사용하였다. 측정된 S$_{11}$값은 셀룰러 CDMA와 IMT-2000 전 대역에서 -l0.9 dB 이하의 특성을 보였으며, 859 MHz와 2027.5 MHz에서 각각 2.38 dBi와 4.02 dBi의 이득을 갖는 전방향 복사패턴을 전산모의실험 결과로 확인하였다. 구현된 안테나는 소형으로서 상용화시 낮은 가격으로 생산할 수 있다.다.