• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.696-697
• /
• 2006

This paper presents the densification and microstructure evolution of bilayer components made from 316L stainless steel and M2 High speed steel during co-sintering process. The sintering was carried out at temperatures ranging from $1230-1320^{\circ}C$ in a reducing atmosphere. The addition of boron to 316L was examined in order to increase the densification rate and improve the sintering compatibility between the two layers. It was shown that the mismatch strain bettwen the two layers induces biaxial stresses during sintering, influencing the densification rate. The effect of boron addition was also found to be positive as it improves the bonding between the two layers.

• Journal of the Korean institute of surface engineering
• /
• v.30 no.6
• /
• pp.365-373
• /
• 1997

316L and 420 Stainless steels were deposited onto AZ9ID commercial magnesium alloy by plasma spray process with various gas flow rate of, TEX>$H_2$ secondary gas. And hardness as well as were track volume, coefficient of friction also had been measured. wear and hardness were measured by using reciprocal configuration tribometer and microghardness tester, respectively. Also, the microstructure of the coatings surface the cross sectional area of coating surface and cross sectional area of coaing/Substrate interface had been analyzed with Scanning Electron Microscope(SEM) and Optical microscope(OM). Finally, optimal process parameters for the improvement of coating efficiency such as mechanical property and wear behavior were examined.

• Corrosion Science and Technology
• /
• v.14 no.4
• /
• pp.184-189
• /
• 2015

In this study, the combined effect of chloride and thiosulfate ions and the effect of the ratio of the two ions on passivation in 304L, 316L, and the duplex stainless steels 2101 and 2205 are investigated using potentiostatic scratch tests. Cyclic polarization and the scratch tests were used to understand the role of anions on localized corrosion in these systems. It was found that the thiosulfate pitting began at a lower potential for 2101 than 304L in 0.6 M NaCl + 0.03 M $Na_2S_2O_3$ solution. The pit morphologies for 304L, 316L, and 2101 in an 0.6 M NaCl + 0.03 M $Na_2S_2O_3$ solution were very different from each other. The results indicate that the pitting switches from predominately thiosulfate pitting to chloride pitting at approximately 0.1 V.

• Journal of the Korean Vacuum Society
• /
• v.19 no.6
• /
• pp.460-466
• /
• 2010

We measured the magnetic properties of stainless steels type 304 and 316L to see if those materials can be used for the applications where non-magnetic materials are required. The results show that the relative permeability of samples was greatly increased during manufacturing processes. After full solution annealing, however the permeability could be reduced to less than 1.02. Thus, the materials may be employed in the low-permeability applications.

• Corrosion Science and Technology
• /
• v.18 no.6
• /
• pp.258-266
• /
• 2019

The objective of this study was to evaluate corrosion resistance of additive manufactured 316L stainless steel and alloy 625 powders widely used in corrosion resistance alloys of marine industry in comparison with cast alloys. Directed Energy Deposition (DED) method was used in this work for sample production. DED parameter adjustment was also studied for optimum manufacturing and for minimizing the influence of defects on corrosion property. Additive manufactured alloys showed lower corrosion resistance in seawater compared to cast alloys. The reason for the degradation of anti-corrosion property was speculated to be due to loss of microstructural integrity intrinsic to the additive manufacturing process. Application of heat treatment with various conditions after DED was attempted. The effect of heat treatments was analyzed with a microstructure study. It was found that 316L and alloy 625 produced by the DED process could recover their expected corrosion resistance when heat treated at 1200 ℃.

• Journal of the Korean Society for Heat Treatment
• /
• v.30 no.6
• /
• pp.271-278
• /
• 2017

This study was carried out to investigate the relationship between the mechanical properties and damping capacity of thermo-mechanical treated 316L stainless steel. Dislocations, ${\varepsilon}$ and ${\alpha}^{\prime}$-martensites were formed by thermo-mechanical treatment, and the grain size was changed from micrometer to sub-micrometer by 5-cycled thermo-mechanical treatment. The volume fraction of dislocations, ${\varepsilon}$ and ${\alpha}^{\prime}$-martensites was increased, and grain size of austenite increased and lengthened by the with increasing cycle number of thermo-mechanical treatment. In 5-cycled specimens, the volume fraction of ${\alpha}^{\prime}$-martensite was more than 25% and the less than 5% of volume fraction of ${\varepsilon}$-martensite was attained. With increasing number of thermo-mechanical treatment, hardness, strength and damping capacity were increased, but elongation was decreased. Damping capacity was increased with increased hardness and strength, but decreased with increased elongation, and this result was the opposite tendency for general metal.

• Transactions of Materials Processing
• /
• v.20 no.2
• /
• pp.118-123
• /
• 2011

Manufacturing of the bipolar plate of a direct methanol fuel cell (DMFC) by direct laser melting technology (DLM) was attempted. The DLM technology is highly influenced by process parameters such as laser power, scan rate and layering height. Therefore, an analysis of the DLM technology was performed under various conditions. The bipolar plates were fabricated using the DLM process with 316L stainless steel (STS 316L) plates and powder. Powder melting trials at various energy density were performed in order to select a feasible melting range for a given laser power. The melting line height increases and eventually saturates when the energy density increases, but decreases when the laser power increases at a given energy density. For the estimation of the potential performance of the bipolar plate, the surface roughness and contact resistance of the DLM layer were also analyzed. The changes of line height and thickness are useful information to report when manufacturing bipolar plate of fuel cell through the DLM process.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.55.2-55.2
• /
• 2009

A polymer electrolyte membrane (PEM) fuel cell has been getting large interest as a typical issue in useful applications. The PEMFC is composed of a membrane, catalyst and the bipolar plate. SnOx:F films on SUS316 stainless steel were prepared as a function of substrate with using electron cyclotron resonance-metal organic chemical vapor deposition (ECR-MOCVD) in order to achieve the corrosion-resistant and low contact resistance bipolar plates for PEM fuel cells. The SnOx:F films coated on SUS316 substrate at surface plasma treatment for excellent stability, before/after heat treatment for good crystalline structure and microwave power for were characterized by X-ray diffraction (XRD), auger electron microscopy (AES) and field emission-scanning electron microscopy (FE-SEM). The SnOx:F film coated on SUS316 substrate with various process parameters were able to observe optimum interfacial contact resistance (ICR) and corrosion resistance. It can be concluded that fluorine-doping content plays an important function in electrical property and characteristic of corrosion-protective film.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.133-138
• /
• 2002

Microbiologically Influenced Corrosion (MIC) was suspected in a corrosion failure of cooling system of stainless piping welded joint, carrying marine water. Marine water which is used for cooling water in a plant was transferred to the laboratory and used for experiment. In the first experiment, weld metal samples were exposed to the test solution for 56 days (marine water and sterilized marine water (control)). Surface condition of experimental coupons was observed using a Scanning Electron Microscope (SEM). In another experiment, free corrosion potential of these material was monitored for 56 days. Pitting corrosion was found in the coupons exposed to marine water. Free corrosion potential ennoblement was found to be significant compared to control. It was suspected that this corrosion case was MIC. In the second experiment, coupons were exposed to diluted nutrient medium containing single culture of microbes isolated from the MIC causing marine water sample used for the first experiment. After exposure test, surface condition of experimental coupon was observed using SEM. Pitting corrosion was found in coupons exposed to some of the isolates. The results indicate that they contribute to the corrosive effect of the SUS316L welds.

• Nuclear Engineering and Technology
• /
• v.55 no.2
• /
• pp.555-565
• /
• 2023

Despite many advantages as structural materials, austenitic stainless steels (SSs) have been avoided in many next generation nuclear systems due to poor void swelling resistance. In this paper, we report the results of heavy ion irradiation to the recently developed advanced radiation resistant austenitic SS (ARES-6P) with nanosized NbC precipitates. Heavy ion irradiation was performed at high temperatures (500 ℃ and 575 ℃) to the damage level of ~200 displacement per atom (dpa). The measured void swelling of ARES-6P was 2-3%, which was considerably less compared to commercial 316 SS and comparable to ferritic martensitic steels. In addition, increment of hardness measured by nano-indentation was much smaller for ARES-6P compared to 316 SS. Though some nanosized NbC precipitates were dissociated under relatively high dose rate (~5.0 × 10^-4 dpa/s), sufficient number of NbC precipitates remained to act as sink sites for the point defects, resulting in such superior radiation resistance.