• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.8 no.3
• /
• pp.317-329
• /
• 1996

By describing the floor slab of a radiant heating system as a one dimensional transient heat exchanger problem, a dynamic analysis model to incorperate with TRNSYS program was developed and their results were compared with experimental results. Results showed that the both of TPOC(Two Parameter On-off Control) and TPSC(Two Parameter Switching Control) method using room air temperature and floor surface temperature as the control parameters does not maintain room air and floor surface temperature exactly at the setting temperatures. But TPSC method is a better candidate for the temperature regulations of room air and floor surface temperature than TPOC method which can keep on the upper and lower limit temperature according to outside temeperature and wall structure etc. And better thermal circumstance can be given by TPSC method than On-off and TPOC method and the overheating which can be occured at the radiant floor heating system with on-off heating control will be reduced.

• KEPCO Journal on Electric Power and Energy
• /
• v.1 no.1
• /
• pp.79-84
• /
• 2015

Transformer is widely used element on power system and industrial area. Especially the transformers installed at power system are exposed to an environment of arbitrary changed. Thus the prediction of degradation and the analysis of response to impulse are important. To conduct those works, the electrical characteristics of system should be analyzed, effectively. But the analysis of electrical characteristic in electric machine level such as pole and pad-mounted transformer is almost no, thus commercial VNA (Vector Network Analyzer) is used to getting the response in wide frequency range. However, the output power of VNA is usually under 10mW, so verification for effectiveness of measuring electrically large component should be conducted, firstly. Next, after getting total S-parameter of transformer, predicting impulse response can be performed in time-domain with circuit simulator. In this paper, it is introduced that verification effectiveness of VNA using transfer function from SFRA (Sweep Frequency Response Analyzer), firstly. Next, total S-parameter, six by six matix form, was built using measured 2 port S-parameter from vector network analyzer. To get the response to impulse which is defined by IEC 60060-1, time-domain simulation is conducted to ADS (Advenced Design System) circuit simulator.

• Journal of the Korean Mathematical Society
• /
• v.54 no.3
• /
• pp.1015-1030
• /
• 2017

This paper is concerned with the following Klein-Gordon-Maxwell system: $$\{-{\Delta}u+{\lambda}V(x)u-(2{\omega}+{\phi}){\phi}u=f(x,u),\;x{\in}\mathbb{R}^3,\\{\Delta}{\phi}=({\omega}+{\phi})u^2,\;x{\in}\mathbb{R}^3$$ where ${\omega}$ > 0 is a constant and ${\lambda}$ is the parameter. Under some suitable assumptions on V (x) and f(x, u), we establish the existence and multiplicity of nontrivial solutions of the above system via variational methods. Our conditions weaken the Ambrosetti Rabinowitz type condition.

• Journal of the Korean Ceramic Society
• /
• v.25 no.6
• /
• pp.639-644
• /
• 1988

The physical and dielectric properties of complex perovskite compound Sr(Mg1/3Nb1/3)O3-Ba(Mg1/3Nb2/3)O3-Ba(Mg1/3Ta2/3)O3(BMT) system were investigated as a function of composition. As the mole ratio of BMN was increased, lattice parameter ratio c/a was slightly increased, and density was increased in SMN-BMN system. However, in BMN-BMT system, lattice parameter ratio c/a and density were decreased with increasing the mole ratio of BMN. Dielectric constant, dielectric loss at $25^{\circ}C$ and 100kHz, and temperature coefficient of resonant frequency, the dependence of temperature in capacitance were increased with increasing the mole ratio of BMN in SMN-BMN-BMT system. These result can be explained according to the degree of order=disorder and dielectric constant.

• Journal of the Korean Society for Heat Treatment
• /
• v.25 no.3
• /
• pp.121-125
• /
• 2012

The large forgings used in chemical plants or nuclear power plants are produced by complex heat treatment. because of thickness up to 200~300 mm and weight up to 200~300 ton, setting proper heat treatment cycle is so difficult. In addition, defects of products make companies wasting large money and valuable time. In this study, to reduce try & err, when setting heat treatment of reactor pressure vessel steel SA508Gr.3, carrying out the basic mechanical property test of SA508 Gr.3 and testing hardness of SA508Gr.3 in various tempering temperature. and calculating temper curve with Hollomon-Jaffe parameter.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.10A
• /
• pp.760-768
• /
• 2009

In this paper, we propose the energy efficient transmission parameter selection method for Wireless Personal Area Network (WPAN) system which is applied to e-Navigation system considering various ship models environment. An appropriate selection of transmission parameters of HR-WPAN system is very essential to be considered for saving WPAN devices' energy consumption, when HR-WPAN system is applied to ship area network (SAN). Therefore, we propose an energy consumption model for a ship area network employing IEEE 802.15.3 based CSMA/CA HR-WPAN model and analyze the effect of transmission parameter selection on the performance of energy consumption. In particular, the path loss is the major performance decision parameter for the SAN employing HR-WPAN system, since it varies according to the material of shipbuilding such as steel(for large ship), FRP(for medium size ship) and compound wood(for small ship). Thus, we analyze and demonstrate that the proper transmission parameter selection of transmit power, PHY data rate and fragment size for each ship model could guarantee energy efficiency.

• Journal of the Korea Computer Industry Society
• /
• v.2 no.7
• /
• pp.895-904
• /
• 2001

In this study, gain can be high because an active double balance mixer was used. Receiving system II was made with receiving system I of low IIP3, a passive double balance mixer which has low gain and high IIP3, and an intermediate frequency amplifier for enhancing the low gain. The result of simulating receiving parameter is as follows： the total NF of receiving system I was 6.4382dB, gain was 53.5dB, and IIP3 was -6.6352dB m. As for the receiving system II, the total NF was 9.70672dB, gain was 47dB, and IIP3 was 3.66729dB m.

• The Journal of Advanced Prosthodontics
• /
• v.10 no.6
• /
• pp.422-429
• /
• 2018

PURPOSE. Accurate color matching of maxillofacial prostheses to skin is important for esthetics. A computerized color matching system specific to human skin has recently been developed. The purpose of this study was to evaluate the accuracy in color and translucency matching of the computerized color matching system across different skin colors. MATERIALS AND METHODS. The silicone was colored to simulate 28 different skin colors (n=5) to serve as "target skin colors". Using a spectrocolorometer (e-skin), color codes were determined for "replicate skin color" fabrication. CIELAB Delta-E between target skin color-replicate skin color pairs and translucency parameter were calculated. CIELAB Delta-E values were compared with one-way ANOVA and Tukey multiple-comparison. The agreement between $L^*$, $a^*$, $b^*$ and translucency parameter of target skin colors and replicate skin color were calculated by a two-way mixed average measures intraclass correlation coefficient. Translucency parameter of target skin color- replicate skin color pairs were compared with Paired t-test (${\alpha}=.05$). RESULTS. The mean CIELAB Delta-E value was 3.83 and significant differences were found among colors. The intraclass correlation coefficient showed excellent reliability for $L^*$, $a^*$, $b^*$ and good reliability for translucency parameter (P<.001). The mean translucency parameter of replicate skin colors was significantly higher than that of translucency parameter. CONCLUSION. The computerized color matching system specific to human skin was found to be reliable in terms of color and translucency between target skin colors and replicate skin color.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.37 no.3
• /
• pp.180-185
• /
• 1988

This paper considers the problem of the optimal input design for parameter estimtion in the ARMAX model in which the system and noise transfer function have the common denominator polynomial. Deriving the information matrix, in detail, for the assumed model structure and using the autocorrelation functin of the filtered input as design variables, it is shown that D-optimal input signal can be realized as an autoregressive moving average process. Computer simulations are carried out to show the standard-deviation reduction in the parameter estimtes using the optimal input signal.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.54 no.3
• /
• pp.122-132
• /
• 2005

This paper presents a novel approach based on Prony method to analysis of small signal stability in power system. Prony method is a valuable tool in identifying transfer function and estimating the modal parameter of power system oscillation from measured or computed discrete time signal. This paper define the relative residue of time signal and propose the condition to select low frequency oscillation in each generator. This paper describes the application results of proposed algorithm with respect to KEPCO systems. Simulation results show that the proposed algorithm can be used as another tools of power systems analysis.