• 마이크로전자및패키징학회지
• /
• 제19권3호
• /
• pp.71-76
• /
• 2012

SnBi 저온솔더의 플립칩 공정을 이용한 스마트 의류용 칩 접속공정에 대해 연구하였다. 캐리어 필름에 형성한 Cu 리드프레임을 $130^{\circ}C$에서 직물에 열압착 시킴으로써 Cu 리드프레임이 전사된 직물 기판을 형성하였다. 칩 시편에 SnBi 페이스트를 도포하여 솔더범프를 형성한 후 직물 기판의 Cu 리드프레임에 배열하고 $180^{\circ}C$에서 60초 동안 유지시켜 플립칩 본딩하였다. SnBi 저온솔더를 사용하여 형성된 스마트 의류용 플립칩 접속부의 평균 접속저항은 $9m{\Omega}$이었다.

• 대한디지털의료영상학회논문지
• /
• 제3권1호
• /
• pp.126-132
• /
• 1997

Purpose : To apply to Program of Auto processor quality control after comparison of Film density variations with amendments to Auto density by using Check density program and Adjust density program of calibration mode into the Laser imager. Methods : Observe Check and Adjust density variations on the Control chart with standard step and value during seven months from December, 1995 to June, 1956 extending twice a week. (1) Measure density value on the steps after printing out 17-step sensitometric pattern of the Check density program. (2) In the same way, measure density values after amending density by using Adjust density program If they are exceeding allowable error limit. Results : In case of Check density program, the exceeding limit rates of Density difference(DD) and Middle density(MD) are: FL-IM3543 DD=75%. MD=72.5%, FL-IMD DD=0%. MD=30.8%(14.5%) After amending density by using Adjust density program, the exceeding limit rates of all both Laser imager were zero percent. The standard deviations are show lower FL-IM D than FL-IM3543 on the Check density control chart, but higher on the Adjust density control chart. Conclusion : (1) Check density variations by printingout sensitometric pattern extending once a week at least for quality control of the Laser imager. (2) In case of a dusty place, check the Laser beam transmission after cleaning Laser optical unit extending once a month. (3) Be sure to measure and check density values by using adjust density program if they are exceeding allowable error limit. (4) Maintain much better film density by performing the adjust density program even if check density values are existed within normal limit.

• Wind and Structures
• /
• 제23권6호
• /
• pp.595-613
• /
• 2016

Large amplitude oscillation of steepled main cables usually presents during construction of a long-span bridge. To study this phenomenon, six typical main cables with different cross sections during construction are investigated. Two main foci have been conducted. Firstly, aerodynamic coefficients of a main cable are obtained and compared through simulation and wind tunnel test: (1) to ensure the simulation accuracy, influences of the numerical model's grid size, and the jaggy edges of main cable's cross section on main cable's aerodynamic coefficients are investigated; (2) aerodynamic coefficients of main cables at different wind attack angles are obtained based on the wind tunnel test in which the experimental model is made by rigid plastic using the 3D Printing Technology; (3) then numerical results are compared with wind tunnel test results, and they are in good agreement. Secondly, aerodynamic coefficients of the six main cables at different wind attack angles are obtained through numerical simulation. Then Den Hartog criterion is used to analyze the transverse galloping of main cables during construction. Results show all the six main cables may undergo galloping, which may be an important reason for the large amplitude oscillation of steepled main cables during construction. The flow structures around the main cables indicate that the characteristic of the airflow trajectory over a steepled main cable may play an important role in the galloping generation. Engineers should take some effective measures to control this harmful phenomenon due to the big possibility of the onset of galloping during the construction period.

• Tribology and Lubricants
• /
• 제22권2호
• /
• pp.59-65
• /
• 2006

In hard disk drives as the head to disk spacing continues to decrease to facilitate recording densities, slider disk interactions have become much more severe due to direct contact of head and disk surfaces in both start/stop and flying cases. The slider disk interaction in CSS (contact-start-stop) mode is an important source of particle generation and tribocharge build-up. The tribocharge build-up in the slider disk interface can cause ESD (electrostatic discharge) damage. In turn, ESD can cause severe melting damage to MR or GMR heads. The spindle speed of typical hard disk drives has increased in recent years from 5400 rpm to 15000 rpm and even higher speeds are anticipated in the near future. And the increasing disk velocity leads to increasing disk acceleration and this might affect the tribocharging phenomena of the slider/disk interface. We investigated the tribocurrent/voltage build-up generated in HDD, operating at increasing disk accelerations. In addition, we examined the effects with relative humidity conditions and rest time. We found that the tribocurrent/voltage was generated during pico-slider/disk interaction and its level was about $3\sim16pA$ and $0.1\sim0.3V$, respectively. Tribocurrent/voltage build-up was reduced with increasing disk acceleration. Higher humidity conditions $(75\sim80%)$ produced lower levels tribovoltage/current. Therefore, a higher tribocharge is expected at a lower disk acceleration and lower relative humidity condition. Rest time affected the charge build-up at the slider-disk interface. The degree of tribocharge build-up increased with increasing rest time.

• 대한방사선기술학회지:방사선기술과학
• /
• 제41권6호
• /
• pp.595-602
• /
• 2018

Quality control (QC) of Computed Tomography (CT) devices is based on image quality measurement on AAPM CT phantom which is a standard phantom. Although it is possible to control the accuracy of the CT apparatus, it is expensive and has a disadvantage of low penetration rate. Therefore, in this study, we make image quality measurement phantom at low cost using FFF (Fused Filament Fabrication) type three-dimensional printer and try to analyze the usefulness, compare it with existing standard phantom. To print a phantom, We used three-dimensional printer of the FFF system and PLA (Poly Lactic Acid, density: $1.24g/cm^3$) filament, and the CT device of 64 MDCT (Aquilion CX, Toshiba, Japan). In addition, we printed a phantom using three-dimensional printer after design using various tool based on existing standard phantom. For image quality evaluation, AAPM CT phantom and self-generated phantom were measured 10 times for each block. The measured data were analyzed for significance using the Mannwhiteney U-test of SPSS (Version 22.0, SPSS, Chicago, IL, USA). As a result of the analysis, phantom fabricated with three-dimensional printer and standard phantom showed no significant difference (p>0.05). Furthermore, we confirmed that image quality measurement performance of a phantom using three-dimensional printer is similar to the existing standard phantom. In conclusion, we confirmed the possibility of low cost phantom fabrication using three dimensional printer.

• International Journal of Computer Science & Network Security
• /
• 제21권2호
• /
• pp.212-220
• /
• 2021

The objectives of this research were to identify the digital competencies required for information science specialists at Saudi universities and to examine whether there existed conspicuous differences in the standpoint of these specialists due to years of work experience with regard to the importance of these competencies. A descriptive analytical method was used to accomplish these objectives while extracting the required digital competency list and ascertaining its importance. The research sample comprised 24 experts in the field of information science from several universities in the Kingdom of Saudi Arabia. The participants in the sample were asked to complete a questionnaire prepared to acquire the pertinent data in the period between January 5, 2021 and January 20, 2021. The results reveal that the digital competencies required for information science specialists at Saudi universities encompass general features such as the ability to use computer, Internet, Web2, Web3, and smartphone applications, digital learning resource development, data processing (big data) and its sharing via the Internet, system analysis, dealing with multiple electronic indexing applications and learning management systems and its features, using electronic bibliographic control tools, artificial intelligence tools, cybersecurity system maintenance, ability to comprehend and use different programming languages, simulation, and augmented reality applications, and knowledge and skills for 3D printing. Furthermore, no statistically significant differences were observed between the mean ranks of scores of specialists with less than 10 years of practical experience and those with practical experience of 10 years or more with regard to conferring importance to digital competencies.

• Design & Manufacturing
• /
• 제14권1호
• /
• pp.1-7
• /
• 2020

In this study, the variation of the shrinkage in the thickness direction of the molded parts according to the gate size of the polymer core fabricated through the 3D printer using the SLS method was studied. The polymer cores are laser sintered and the powder material is nylon base PA2200. The polymer cores have lower heat transfer rate and rigidity than the metal core due to the characteristics of the material. Therefore, the injection molding test conditions are set to minimize the deformation of the core during the injection process. The resin used in the injection molding test is a PP material. The packing condition was set to 80, 90 and 100% of the maximum injection pressure for each gate size. The runner diameter used was ∅3mm, and the gates were fabricated in semicircle shapes with cross sections 1, 2, and 3 ㎟, respectively. Thickness measurement was performed for 10 points at 2.5 mm intervals from the point 2.5 mm away from the gate, and the shrinkage to thickness was measured for each point. The shrinkage rate according to the gate size tends to decrease as the cross-sectional area decreases as the maximum injection pressure increases. The average thickness shrinkage rate was close to 0% when the packing pressure was 90% for the gate area of 1mm2. When the holding pressure was set to 100%, the shrinkage was found to decrease by 3% from the standard dimension due to the over-packing phenomenon. Therefore, the smaller the gate, the more closely the molded dimensions can be molded due to the high pressure generation. It was confirmed that precise packing process control is necessary because over-packing phenomenon may occur.

• 대한치과보철학회지
• /
• 제57권3호
• /
• pp.211-218
• /
• 2019

목적: 본 연구에서는 CAD/CAM 기술로 제작한 4가지 금속하부구조물의 변연 및 내면 적합도를 비교하여 정확도 및 임상적 효용성을 알아보고자 한다. 재료 및 방법: 상악 중절치 레진모형치아를 삭제한 뒤 복제하여 Ni-Cr 합금 표준 모형을 제작하였다. 이를 공초점 현미경방식의 구강 스캐너를 이용해 12개의 STL 파일을 얻었다. CAD 프로그램 상에서 $50{\mu}m$의 시멘트 공간을 부여한 두께 0.5 mm의 금속하부구조물을 디자인하였다. Co-Cr 금속하부구조물은 다음 4가지 방법으로 제작하였다: Wax pattern milling & Casting (WM), Resin pattern 3D Printing & casting (RP), Milling & Sintering (MS), Selective laser melting (SLM). 변연 및 내면 적합도를 측정하기 위해 실리콘 복제법을 이용하였다. 측정한 결과값은 SPSS 통계 프로그램을 이용하여 일원배치분산분석(one-way ANOVA)으로 통계처리하고, 사후검정으로 Scheffe test를 시행하였으며, 5% 유의수준으로 평가하였다(${\alpha}=.05$). 결과: 변연 적합도는 WM군($27.66{\pm}9.85{\mu}m$)과 MS군($28.88{\pm}10.13{\mu}m$)이 RP군($38.09{\pm}11.14{\mu}m$)에 비해 통계적으로 유의하게 작았다. 치경부 적합도는 MS군이 RP군에 비해 통계적으로 유의하게 작았다. 축면 적합도는 WM군과 MS군이 RP군과 SLM군 보다 통계적으로 유의하게 작았다. 절단면 적합도는 RP군이 통계적으로 유의하게 작았다. 결론: Wax pattern milling & Casting, Milling & Sintering법으로 제작한 Co-Cr coping의 변연과 축면에서의 적합도가 더 우수하였다. 모든 군의 Co-Cr coping의 변연, 치경부, 축면 적합도는 임상적으로 허용할만한 범위 안에 있었다.

• 한국산학기술학회논문지
• /
• 제19권10호
• /
• pp.136-142
• /
• 2018

3D 프린팅 공법으로 알려진 적층 공정 기술은 지속적인 소재 개발을 바탕으로 모형 제작부터 상용화 부품 제작까지 활용도를 확장하고 있다. 최근 들어 고강도 엔지니어링 플라스틱 소재 중의 하나인 polyamide (폴리아미드) 계열의 고분자를 활용하여 경량화 및 고강도의 부품을 제작하는 연구 개발이 활발히 진행되고 있다. 이번 연구에서는 polyamide 12 (PA12) 소재를 대상으로 Izod 충격 특성을 분석하였다. 시편 제작을 위해 기계적 특성이 우수한 선택적 레이저 소결 (Selective Laser Sintering) 공정 방식을 적용하였으며, PA12 및 글라스 비드 (glass bead) 보강 PA12 소재로 구분하여 제작하였다. 시편은 제작 플랫폼 상의 제작방향 별로 구분하였으며, 각 시험편을 $-25^{\circ}C$, $25^{\circ}C$, $60^{\circ}C$의 시험온도 환경에서 Izod 테스트를 진행하였다. 그 결과로, 각 PA12 및 글라스 비드 보강 PA12의 충격강도 값은, $25^{\circ}C$시험온도에서 제작방향이 수직인 경우 평행 시편 대비하여 48.8% 및 16.3%의 충격강도 값 저하를, 시험 온도에 따른 영향으로는 평행 시편을 기준으로 $60^{\circ}C$의 충격강도 값이 $-25^{\circ}C$ 대비하여 46.5% 및 20.4% 향상됨을 확인할 수 있었다.

• 전기화학회지
• /
• 제2권4호
• /
• pp.227-231
• /
• 1999

Carbon paste전극을 백금도금 한 후 이 전극을 사용한 일회용 전류법 glucose센서를 제작하였다. 전극에 시료용액을 가한 후, voltammetry을 이용하여 본 센서의 감응성을 연구하였다. screen printing된 carbon paste전극 표면 위에 전기도금 방법으로 도입된 백금은 센서의 분석성능과 mediator의 전기 화학적 가역성을 크게 향상시켜 준다. 제작된 센서가 $[Fe(CN)_6]^{4-/3-}$에 대한 heterogeneous rate constant는 $1.45\times10^{-2}cm{\cdot}s^{-1}$이며, 이 센서는 적용전위 0.3V vs. Ag/AgCl에서 glucose에 대한 좋은 감응성을 보여주었다. 이 때 glucose에 대한 Michaelis-Menten상수는 24.5mM이다. 일회용 glucose 스트립 센서의 분석성능을 평가하기 위하여 NOVA S.P. Ultra M analyzer와 비교실험을 수행하였다. 이 때 시료용액으로서 $80\~297 mg/dL$ 범위의 glucose를 함유하고 있는 30여 종류의 혈청을 사용하였고, 상관계수는 0.983으로서 정밀도와 정확도가 비교적 우수함을 보여주었다.