• Structural Engineering and Mechanics
• /
• 제70권1호
• /
• pp.13-31
• /
• 2019

A nonlinear finite element model (FEM) using ATENA-3D software to simulate the axially compressive behavior of circular steel tube confined concrete (CSTCC) columns infilled with ultra high performance concrete (UHPC) was presented in this paper. Some modifications to the material type "CC3DNonlinCementitious2User" of UHPC without and with the incorporation of steel fibers (UHPFRC) in compression and tension were adopted in FEM. The predictions of utimate strength and axial load versus axial strain curves obtained from FEM were in a good agreement with the test results of eighteen tested columns. Based on the results of FEM, the load distribution on the steel tube and the concrete core was derived for each modeled column. Furthermore, the effect of bonding between the steel tube and the concrete core was clarified by the change of friction coefficient in the material type "CC3DInterface" in FEM. The numerical results revealed that the increase in the friction coefficient leads to a greater contribution from the steel tube, a decrease in the ultimate load and an increase in the magnitude of the loss of load capacity. By comparing the results of FEM with experimental results, the appropriate friction coefficient between the steel tube and the concrete core was defined as 0.3 to 0.6. In addition to the numerical evaluation, eighteen analytical models for confined concrete in the literature were used to predict the peak confined strength to assess their suitability. To cope with CSTCC stub and intermediate columns, the equations for estimating the lateral confining stress and the equations for considering the slenderness in the selected models were proposed. It was found that all selected models except for EC2 (2004) gave a very good prediction. Among them, the model of Bing et al. (2001) was the best predictor.

• 한국도로학회논문집
• /
• 제11권4호
• /
• pp.79-85
• /
• 2009

국내의 줄눈 콘크리트 포장설계에 주로 사용되는 다웰바 설계 기준은 국외 기준과 검증되지 않은 경험에 의해 사용되고 있다. 또한 다웰바의 설치는 길어깨나 하부층의 조건 등을 고려하지 못한 상태에서 슬래브 폭에 대하여 일률적으로 적용되고 있다. 이에 다웰바를 합리적으로 설계하기 위해서는 다웰바 거동에 대한 고찰이 요구되며, 이를 3차원 유한요소해석을 이용하여 수행하였다. 다웰바의 거동에 대한 3차원 유한요소해석 결과의 타당성을 검토하기 위하여 Timoshenko이론의 다웰바 거동을 비교하였다. 또한 실제 도로에서 교통하중이 여러 개의 다웰바에 분산 전달하는 다웰바의 그룹작용(Dowel Group Action)을 3차원 유한요소해석을 통하여 다웰바 그룹작용 적용범위를 산정하였다. 본 연구에서 제시된 다웰바 그룹작용 범위는 Friberg의 그룹작용 범위와는 상이한 결과가 나타났으며, 비교적 최근 연구 결과인 Tabatabaie의 그룹작용 범위의 연구결과와 유사한 결과가 도출되었다.

• 전기학회논문지
• /
• 제61권3호
• /
• pp.427-432
• /
• 2012

In this paper, we have designed and fabricated 7-bands (GSM 850/900, DCS/PCS, and UMTS 3 bands) LTCC front end module (FEM) embedded LPF (low pass filter) to efficiently eliminate harmonics generated in TX path. The proposed FEM is composed of flip-chip typed CMOS SP9T switch to select transceiver signals, dual type SAW filters to receive Rx signals, and 0603 size chip components for the antenna matching and ESD protection. The whole size of FEM is $4.5{\times}3.2{\times}1.2mm^3$. The insertion loss of Tx and Rx ports are measured at 1.7 dB and 4.8 dB, respectively.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 A
• /
• pp.134-136
• /
• 1998

When a MCCB Instant trip spring which is adjusted to notrip at -20% of each current from $5{\times}In$ to $10{\times}In$ and trip +20% of those is designed, we should know attraction force between Fixed Magnet and Armature. So we first made some samples, do experiments of weight, and simulated the modelling by 3D Maxwell S/W. With values of experiment and simulated values, we do design instant trip springs and repeat the above process. Finally we set up the Process of designing Instant spring. With it, we can save time and R&D cost.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 A
• /
• pp.34-36
• /
• 1999

2 phase 8 pole HB type LPM(linear pulse motor) has the suitable structure for it's microstep drive. Hence, if this LPM will be drived by this method, the limited(mechanically) step resolution can be increased further and vibration and noise can be decreased considerably. But, It is difficult that this LPM was analyzed in detail because of it's complex magnetic circuits to be composed the LF(longitudinal flux) and TF(transverse flux.) path. If LPM was analyzed by the approximate 2D model, we could not be obtained satisfactory result. Therefore, It is necessary to be analyzed the 3D model in detail for the more satisfactory results. In this paper, we obtain 3D flux distribution of the mover using by 3D FEM(finite element method)

• 한국임상수의학회지
• /
• 제40권4호
• /
• pp.268-275
• /
• 2023

In this paper, we designed 3D-printed orthopedic splint models for patient-specific external coaptation on fracture healing and analyzed the stability of the models through finite element method (FEM) analysis under compressive load conditions. Polylactic acid (PLA) and acrylonitrile-butadiene-styrene (ABS) based 3D splint models of the thicknesses 1, 3, 5 and 7 mm were designed, and Peak von Mises stress (PVMS) and maximum displacement (MD) of the models were analyzed by FEM under compressive loads of 50, 100, 150, and 200 N. The FEM results indicated that PVMS and MD values, regardless of material, had a negative correlation with the thickness of the models and a positive correlation with the compressive load. There was a risk of splint deformation under conditions more extreme than 100 N with 5 mm thickness. For successful clinical application of 3D-printed orthopedic splints in veterinary medicine, it is recommended that the splint should be produced not less than 5 mm thickness. Also, it is expected to be stable when the splint is applied to situations with a compressive load of 100 N or less. There is an advantage of overcoming the limitations of the existing bandage method through 3D-printing technology as well as verifying the stability through 3D modeling before application. Such 3D printing technology will be widely used in veterinary medicine and various fields as well as orthopedics.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 추계학술대회논문집
• /
• pp.14-17
• /
• 1999

The finite element formulation is developed for predicting strain distributions and weld line movements in the forming processes of laser welded blank. The welded zone(WZ) is modelled with several narrow finite elements whose material characteristics are analytically obtained from those of base metals based on the tensile tests. In order to show the reliability and effectiveness of weld element the forming process of hemispherical dome stretching and auto-body door inner panel stamping are simulated FEM predictions show good agreements with experimental observations.

• Journal of Electrical Engineering and Technology
• /
• 제5권3호
• /
• pp.431-434
• /
• 2010

This paper presents the torque calculation method of a permanent magnet spherical motor. To calculate using the finite element method (FEM), three-dimensional (3D) FEM must be used. However, since the method requires excessive time and memory, an easier torque calculation method is hereby presented. In the proposed method, it is very important to obtain the approximation function of the torque profile curve. We present the approximation method of the torque profile curve and show that the torque calculation result can approximate the torque obtained by 3-D FEM.

• 한국터널지하공간학회 논문집
• /
• 제4권1호
• /
• pp.3-12
• /
• 2002

본 연구는 우면산터널 시공에 따른 예술의 전당내의 오페라극장 구조물에 대한 영향을 검토하고 필요시에는 적절한 대책을 조기에 강구하기 위하여 3차원 유한요소해석을 실시하였다. 쌍굴터널 굴진시 지반거동의 영향범위내에 있는 오페라극장은 문화재급의 건축물로써 그 기초형식 또한 다양하다. 그러므로, 건물구조의 3차원적인 특성과 기초형태의 변화를 이상적으로 모델링하고, 3차원해석 결과에 따른 시공전 예측과 시공중 안정성확인을 평가할 수 있도록 검토하였다. 문제발생시 신속한 대처를 할 수 있고, 터널굴진시 정보화 시공이 적용될 수 있도록 관리기준치를 단계적으로 변화 설정하였다.

• 한국전산구조공학회논문집
• /
• 제33권1호
• /
• pp.63-72
• /
• 2020

본 연구의 목적은 원자로 1400(APR 1400) 원자력 발전소(NPP)의 원자로 격납건물(RCB) 내진성능에 대해 상이한 수치모델과 지진 주파수 성분의 영향을 평가하는 것이다. 집중 질량 막대 모델(lumped-mass stick model, LMSM)과 3차원 유한요소모델(three-dimensional finite element model, 3D FEM)의 두 가지 수치 모델이 시간이력해석을 수행하기 위해 개발되었다. LMSM은 기존의 집중 질량 보-요소를 사용하여 SAP2000으로 구성하였으며, 3D FEM은 각기둥 입체-요소를 사용하여 ANSYS로 작성되었다. 저주파수 및 고주파수 성분을 고려한 두 그룹의 지진파를 시간이력해석에 적용하였다. 저주파수 지진파의 응답스펙트럼을 NRC 1.60의 설계 스펙트럼과 일치되도록 조정하여 작성하였으며, 고주파수 지진파는 10Hz ~ 100Hz의 고주파수 범위를 갖도록 생성하였다. RCB의 지진응답은 다양한 높이에서 층응답스펙트럼으로 검토하였다. 수치해석 결과, 저주파수 지진에 의한 구조물의 FRS 결과는 두 수치 모델에서 매우 유사한 결과를 보였다. 하지만, 고주파수 지진에 의한 LMSM의 FRS 결과는 고차 고유 주파수 영역에서 3D FEM과 큰 차이를 보였으며, RCB의 낮은 높이에서 명확한 차이를 보였다. 3D FEM이 정확한 구조물의 응답을 나타내는 것으로 가정한다면, RCB의 LMSM은 고주파수 지진에 의한 FRS 결과의 고차 고유 주파수 영역에서 일정 수준의 불일치성을 내포하고 있다.