• 한국안전학회지
• /
• 제24권6호
• /
• pp.103-110
• /
• 2009

Since the mechanical properties of cement-based materials are time-dependent due to the prolonged cement hydration process, those of fiber reinforced concrete(FRC) may also be time-dependent. Toughness is one of important properties of FRC. Therefore, it should be investigated toughness development of FRCs with curing ages to fully understand the time-dependent characteristics of FRCs. To this end, the effect of curing ages on flexural toughness development of steel fiber reinforced concrete is studied. Three point bending test with notched beam specimen was adapted for this study. Hooked-end steel fiber(DRAMIX 40/30) was used as a fiber ingredient to investigate w/c ratio and fiber volume fraction effect on toughness development during curing. Three different water-cement ratios(0.44, 0.5 and 0.6) and fiber volume fractions(0%, 0.5% and 1%) were used as influence factors. Each mixture specimens were tested at five different ages, 0.5, 1, 3, 7 and 28 days. The study shows that flexure toughness development with age is quite different than other concrete material properties such as compressive strength. The study also shows that the toughness development trend correlates more closely to water/cement ratio than to fiber volume fraction.

• 한국전기전자재료학회논문지
• /
• 제21권2호
• /
• pp.144-150
• /
• 2008

Recently, there has been growing interest in low loss and low dielectric constant material for LTCC application, as the frequency range for electronic devices increases. This study was designed to evaluate the effect of cordierite filler for low dielectric constant LTCC material. From the previous experiments, two glass compositions of B-Si-Al-Zn-Ba-Ca-O and B-Si-Al-Sr-Ca-O system, were chosen. Each powder of two glass compositions was sintered respectively with commercial cordierite powder in temperature range from $800^{\circ}C\;to\;900^{\circ}C$. Crystalline cordierite and glass peaks were affected only with two factors of composition and sintering temperature among various factors. With the optimized condition of two cordierite/glass compositions, obtained dielectric constant was below 5.5 and quality factor was above 1,000. Closed pore of sintered body was controled by sintering temperature and sintering time. When cordierite/glass composite with ratio of 5.5:4.5 was sintered at $900^{\circ}C$, densification was sufficient with good dielectric characteristics of ${\epsilon}_r<5.1,\;Q{\ge}1,000$. Residual fine closed pores could be reduced with control of sintering temperature and time. 3 point bending strength and chemical durability were evaluated to obtain feasibility for substrate material.

• Journal of Welding and Joining
• /
• 제20권1호
• /
• pp.34-40
• /
• 2002

The laser strengthening of $35kgf/\textrm{mm}^2$ grade steel sheet is investigated by using $CO_2$ laser beam irradiation. The increase of tensile strength is dominated by the number of fully penetrated melting lines. Also, the optimal laser irradiation pattern is obtained by 3-point bending test. Local laser strengthening clay be effective for the weight reduction of automobile components where the tailored welded blank can not be applied.

• Journal of the Korean Wood Science and Technology
• /
• 제31권3호
• /
• pp.42-49
• /
• 2003

The objective of this research was to investigate the possibility of using rice husk flour as a partial substitute for the wood particles used as the raw material for manufacturing particleboards, by examining the physical and mechanical properties of the rice husk flour-wood particleboard as a function of the type of urea-formaldehyde resin used. Commercial wood particles and two types of rice husk flours (A type (30 ㎛), B type (300 ㎛)) were used. E₁ and E₂ class urea-formaldehyde resin was used as the composite binder, combined with 10 wt.% NH₄Cl solution as a hardener. Rice husk flour-wood particleboards with dimensions of 27×27×0.7 (cm) were manufactured at a specific gravity of 0.7 with rice husk flour contents of 0, 5, 10, and 15 (wt.%). We examined the physical properties (specific gravity and moisture content), mechanical properties (three point bending strength and internal bonding) of the composite. In general, it can be concluded that composites made from rice husk flours are of somewhat poorer quality than those made from wood; however, blending in small amounts of rice husk flour (e.g., 5% to 10% by weight) may have no significant impact on quality.

• Structural Engineering and Mechanics
• /
• 제87권4호
• /
• pp.375-389
• /
• 2023

In many fiber concrete beams with Carbon Fiber Reinforced Polymer (CFRP), debonding occurs between the carbon sheets and the concrete due to the low strength of the bonding resin. A total of 42 fiber concrete beams with a cross-section of 10×10 cm with a span length of 50 cm are fabricated and retrofitted with CFRP and subjected to a 4-point bending test. Graphene Oxide (GO) at 1, 2, and 3 wt% of the resin is used to improve the mechanical properties of the bonding resins, and the effect of length, width, and the number of layers of CFRP and resin material are investigated. The crack pattern, failure mode, and stress-strain curve are analyzed and compared in each case. The results showed that adding GO to polyamine resin could improve the bonding between the resin and the fiber concrete beam. Furthermore, the optimum amount of nanomaterials is equal to 2% by the weight of the resin. Using 2% nanomaterials showed that by increasing the length, width, and number of layers, the bearing and stiffness of fiber concrete beams increased significantly.

• Structural Engineering and Mechanics
• /
• 제88권1호
• /
• pp.67-81
• /
• 2023

The reinforced concrete (RC) structures might need strengthening or upgradation due to adverse environmental conditions, design defects, modification requirements, and to prolong the expected lifespan. The RC beams have been efficiently strengthened using the near surface mounted (NSM) approach over the externally bonded reinforcing (EBR) system. In this study, the performance of RC beam elements strengthened with NSM-steel rebars was investigated using an experimental program and nonlinear finite element modeling (FEM). Nine medium-sized, rectangular cross-section RC beams total in number made up for the experimental evaluation. The beams strengthened with varying percentages of NSM reinforcement, and the number of grooves was assessed in four-point bending experiments up to failure. Based on the experimental evaluation, the load-displacement response, crack features, and failure modes of the strengthened beams were recorded and considered. According to the experimental findings, NSM steel greatly improved the flexural strength (up to about 84%) and stiffness of RC beams. The flexural response of the tested beams was simulated using a 3D non-linear finite element (FE) model. The findings of the experiments and the numerical analysis showed good agreement. The effect of the NSM groove and reinforcement on the structural response was then assessed parametrically.

• 상하수도학회지
• /
• 제12권4호
• /
• pp.86-96
• /
• 1998

In this study, an intermittently aerated activated sludge process, modified process from conventional activated sludge process, was developed to treat high strength swine wastewater, which has been blamed as major pollutant for stream pollution. Therefore, the optimum cycle for oxic and anoxic period, SRT, and OLR were studied as design parameters. The effects of different time interval for oxic and anoxic period on nitrification and denitrification were examined by operating two reactors with 60/60min and 60/90min as oxic/anoxic period. Although the reactor with 60/60min showed complete denitrification of $NO_x-N$ generated during oxic period, the reactor with 60/90min showed incomplete nitrification due to the inactivity of nitrifier by accumulated $NH_3-N$ toxicity during anoxic period. Therefore, it is recommended to operate same interval for oxic and anoxic period. In order to determine the optimum cycle for oxic/anoxic period, four different reactors with 30/30, 60/60, 90/90 and 120/120min were examined. The reactor operation with 90/90min was optimum to get the most stable results in this study. However, the optimum cycle for oxic and anoxic period should be changed with characteristics of influent wastewater and operating conditions. According to lie operation results of three reactors with SRT of 15, 20 and 30days. The reactor with 2Odays SRT showed best removal efficiency of T-N. The optimum OLR would be $2.5Kg\;COD/m^3/day$ which showed the most stable nitrification and denitrification. Since characteristics of influent wastewater in the real system has a severe fluctuation, so it is very difficult to determine each interval for oxic and anoxic period. Therefore, ORP curves, describing the change of oxidation/reduction potential in reactor, can be used as a control parameter for automatic control of oxic and anoxic period. In other words, bending point (Nitrate Knee) of ORP curve during anoxic period could be used as a starting point of oxic period.

• 한국구조물진단유지관리공학회 논문집
• /
• 제27권1호
• /
• pp.46-53
• /
• 2023

이 논문에서는 고인성 시멘트 복합체 SHCC와 함께 일반 철근, 초고강도 철근, FRP 보강근으로 보강된 3종류의 철근콘크리트 보(SHCC-RB, SHCC-SB, SHCC-FRP)의 휨 성능을 평가하기 위하여 보 실험체를 제작하고, 4점 재하 휨 실험을 수행하였다. 실험 결과, SHCC로 보강된 모든 실험체가 다수의 미세 균열이 발생하면서 휨 균열 폭이 100 ㎛ 이하로 제어되는 특성을 나타내었다. 이는 1축 인장 하에서 인장변형경화 특성을 보이며, 다중 미세균열 특성을 보이는 SHCC의 재료적 성질에 기인하는 것으로 판단된다. 실험체 SHCC-FRP는 실험체 SHCC-RB에 비하여 초기균열하중과 항복 휨모멘트강도가 낮은 반면, SHCC-FRP의 최대 휨모멘트강도는 SHCC-RC에 비하여 우수하게 나타났는데, 이는 FRP 보강근의 인장강도가 일반 철근에 비하여 더 높기 때문이다. 보 실험체 SHCC-SB의 초기균열 하중은 SHCC-RB와 유사하였으나, 항복 휨모멘트강도 및 최대 휨모멘트강도 측면에서는 SHCC-SB가 가장 우수한 것으로 평가되었다. SHCC와 초고강도 철근을 RC보의 보강에 활용하면 작은 단면적의 추가 배근으로도 효과적인 보강이 가능할 수 것으로 판단된다.

• The Journal of Advanced Prosthodontics
• /
• 제10권2호
• /
• pp.113-121
• /
• 2018

PURPOSE. The aim of this preliminary study was to investigate, for the first time, the effects of addition of titania nanotubes ($n-TiO_2$) to poly methyl methacrylate (PMMA) on mechanical properties of PMMA denture base. MATERIALS AND METHODS. $TiO_2$ nanotubes were prepared using alkaline hydrothermal process. Obtained nanotubes were assessed using FESEM-EDX, XRD, and FT-IR. For 3 experiments of this study (fracture toughness, three-point bending flexural strength, and Vickers microhardness), 135 specimens were prepared according to ISO 20795-1:2013 (n of each experiment=45). For each experiment, PMMA was mixed with 0% (control), 2.5 wt%, and 5 wt% nanotubes. From each $TiO_2$:PMMA ratio, 15 specimens were fabricated for each experiment. Effects of $n-TiO_2$ addition on 3 mechanical properties were assessed using Pearson, ANOVA, and Tukey tests. RESULTS. SEM images of $n-TiO_2$ exhibited the presence of elongated tubular structures. The XRD pattern of synthesized $n-TiO_2$ represented the anatase crystal phase of $TiO_2$. Moderate to very strong significant positive correlations were observed between the concentration of $n-TiO_2$ and each of the 3 physicomechanical properties of PMMA (Pearson's P value ${\leq}.001$, correlation coefficient ranging between 0.5 and 0.9). Flexural strength and hardness values of specimens modified with both 2.5 and 5 wt% $n-TiO_2$ were significantly higher than those of control ($P{\leq}.001$). Fracture toughness of samples reinforced with 5 wt% $n-TiO_2$ (but not those of 2.5% $n-TiO_2$) was higher than control (P=.002). CONCLUSION. Titania nanotubes were successfully introduced for the first time as a means of enhancing the hardness, flexural strength, and fracture toughness of denture base PMMA.

• Composites Research
• /
• 제13권6호
• /
• pp.1-8
• /
• 2000

무가압함침법에 의한 $Al_2O_{3p}$/AC8A 복합재료의 제조와, 제조법과 관련하여 부가적인 Mg의 첨가와 강화상의 부피분율이 $Al_2O_{3p}$/AC8A복합재료의 기계적 성질과 마모저항에 미치는 영향을 조사하였다. 강화상 입자와 기지재료의 일부를 분말로 조합한 혼합분말 속으로 기지금속을 자발적으로 침투시켜 부피분율이 20~40%인 $Al_2O_{3p}$/AC8A 복합재료를 제조할 수 있었다. 그러나 강화상의 부피분율이 40%인 복합재료의 경우 기공율의 상승으로 복합재료의 강도는 저하하였다. Mg의 첨가량이 5~7wt% 일 때 가장 높은 강도를 나타냈으며, 경도는 Mg 첨가량의 증가에 따라 점진적으로 상승하였다. $Al_2O_{3p}$/AC8A복합재료는 저속에서 기지재료에 비해 내마모성이 저하하였으나, 고속에서는 AC8A합금에 비해 약 5.5배의 우수한 내마모성을 나타냈다. 마모기구의 관찰에 의해 부피분율 20% $Al_2O_{3p}$/AC8A복합재료의 경우 연삭마모가 주된 마모기구임을 알 수 있었으며, 부피분율 40% $Al_2O_{3p}$/AC8A복합재료는 높은 기공율로 인한 마모 가중으로 저속에서도 경미한 응착마모가 관찰됐고 마찰 속도가 증가함에 따라 격심한 마모로 진행되었다.