• 한국자동차공학회논문집
• /
• 제5권3호
• /
• pp.202-208
• /
• 1997

The knocking is one of major parameters to improve engine performance in a spark ignition engine. Many researches have been carried out to identify them using cylinder pressure, vibration signal and so on. In the present study, measurement and analysis was conducted to set up the criteria of knock occurrence by using microphone signal. Cylinder pressure was measured for the reference signal of knocking. It has been observed that resonance frequencies of pressure wave are nearly independent of engine operating conditions such as engine speed, air fuel ratio, load and octane number of fuel within to limited experimental conditions. SDBP(sum of different band-pass data) method using resonance frequency of knock was proposed for estimating knock intensity. SDBP method is superior to identify knock occurrence and its intensity in case of sound pressure measurement.

• 한국자동차공학회논문집
• /
• 제2권3호
• /
• pp.40-49
• /
• 1994

This paper describes the method to investigate combustion pressure in the cylinder without modifications of engine. Assuming engine dynamics as a single degree of freedom cylinder pressure is estimated using the variation of crank shaft speed. For this study pressure, crank shaft sped, and load are sampled by the crank angle. This study suggests the variation of crank shaft speed can be used as parameters of feedback engine control.

• 한국자동차공학회논문집
• /
• 제5권3호
• /
• pp.27-34
• /
• 1997

The effects of the intake and exhaust valve timing to improve the engine performance in a spark ignition 3-cylinder LPG engine with a closed loop fuel supply system were studied. The engine torque and power have been measured using the 75kW EC-dynamometer while adjusting the optimal fuel consumption ratio with a solen- oid driver. As the results from this experiment, when intake valve opening is $12^{\circ}$ BTDC, intake valve closing is $36^{\circ}$ ABDC, exhaust valve opening is $12^{\circ}$ ATDC, and exhaust valve closing is $36^{\circ}$ BBDC respectively, the best torque characteristics in low and high speeds for a gives engine were obtained. And also we could find that the torque characteristics in low speeds were affected by the timing of exhaust valve open. An increased valve overlap by the EVC delay was ineffectual to the torque characte- ristics improvement in high speeds.

• 대한기계학회논문집B
• /
• 제24권6호
• /
• pp.880-885
• /
• 2000

Flow patterns and steady flow characteristics of an intake 3valve cylinder head are not obviously declared. Thus, in the study, the characteristics and limitation of intake flow coefficient which applied to multi intake valve engine are introduced. The flow coefficient and tumble characteristics are investigated by means of the steady flow test and flow visualization method. As the results, it is found that the intake flow rate is dominated by effective valve open area. In addition, this paper shows that the mass flow rate of intake 3valve engine is greater than that of intake 2valve engine and tumble flow of intake 3valve engine is superior to that of intake 2valve engine.

• 수산해양기술연구
• /
• 제56권3호
• /
• pp.230-237
• /
• 2020

In order to design a diesel engine system and predict its performance, it is necessary to analyze the gas flow of the intake and exhaust system. A gas flow analysis in three-dimensional (3D) format needs a high-resolution workstation and enormous time for analysis. Therefore, the method of characteristics (MOC) was used for a gas flow analysis with a fast calculation time and a low-resolution workstation. An experiment was conducted on a single cylinder diesel engine to measure pressure in cylinder, intake pipe and exhaust pipe. The one-dimensional (1D) gas flow was analyzed under the same conditions as the experiment. The engine speed, valve timing and compression ratio were the same conditions and the intake pressure was inputted as the experimental results. Bent pipe such as an exhaust port that cannot be realized in 1D was omitted. As results of validation, the cylinder pressure showed accuracy, but the exhaust pipe pressure exhibited inaccuracy. This is considered as an error caused by the failure to implement a bent pipe such as an exhaust port. When analyzed in 3D, calculation time required 61 hours more based on a model of this study. In the future, we intend to implement a bent pipe that cannot be realized in 1D using 3D and prepare a method to supplement reliability by using 1D-3D coupling.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권6호
• /
• pp.800-808
• /
• 1998

In this study the thermal stress distribution and deformantion characteristics resulting from the nonuniform temperature fields of the cylinder block of a light 3-cylinder 4-stroke gasoline engine were analyzed using the 3-dimensional finite element method. The temperature distributions req-uisite for the thermoelastic behavior alalysis were obtained from the steady-state heat conduction analysis performed on the basis of experimental data. in order to examine the effect of a ceramic material the cylinder liner was replaced by the silicon nitride($Si_{3}N_{4}$) and its thermal behaviors were compared with those of the original block.

• Journal of Biosystems Engineering
• /
• 제28권4호
• /
• pp.285-294
• /
• 2003

This study was carried out to propose a new-concept internal combustion engine which has great potential advantages to the conventional engines. Proposed new-concept engine is a kind of rotary engine. A rotor is rotating concentrically in a cylinder which is divided into two partitioning valves, and it makes four compartments in the cylinder. The volumes of each of four compartments are changing continuously with the rotor movement and performs the functions of intake, compression. expansion and exhaust simultaneously. Expected thermal efficiency for the real cycle is 26 percent at conditions of 1,000 rpm and compression ratio of 8.0, which is 3 to 4 percent higher than that of the conventional engines such as the piston engine, gas turbine and Wankel rotary engine. A simulation procedure proved that the new concept engine is functional, and has many potential advantages compared to the existing conventional engines.

• 한국자동차공학회논문집
• /
• 제23권2호
• /
• pp.221-229
• /
• 2015

The PFI dual injection engine using one injector per an intake port was developed for solving the DISI engine cost problem. Excellent fuel atomization and targeting of the PFI dual injection engine made enhancement on the fuel efficiency and engine power. In order to develop a PFI dual injection engine, characteristics of the in-cylinder flow and fuel behavior with respect to fuel injection angle and cone angle of the PFI dual injection engine was investigated. Numerical calculation was conducted to analyze 3D unsteady in-cylinder flow and fuel behavior using STAR-CD. The engine operating condition was 2,000rpm at WOT. As a result, the amount of intake air, evaporated fuel and fuel film according to injection angle and cone angle were presented. The results were influenced by interaction between injected fuel and intake port wall.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권1호
• /
• pp.26-33
• /
• 2007

The intake swirl motion, as one of dominant effects for an engine combustion. is very effective for turbulence enhancement during the compression process in the cylinder of 2-valve engine. Because the combustion flame speed is determined by the turbulence that is mainly generated from the mean flow of the charge air motion in intake port system. This paper describes the experimental results of swirl flow and combustion characteristics by using the oil spot method and back-scattering Laser Doppler velocimeter (LDV) in 2-valve single cylinder transparent LPG engine using the liquid phase LPG injection. For this. various intake port configurations were developed by using the flow box system and swirl ratios for different intake port configurations were determined by impulse swirl meter in a steady flow rig test. And the effects of intake swirl ratio on combustion characteristics in an LPG engine were analyzed with some analysis parameters that is swirl ratio. mean flow coefficient, swirl mean velocity fuel conversion efficiency. combustion duration and cyclic variations of indicated mean effective pressure(IMEP). As these research results, we found that the intake port configuration with swirl ratio of 2.0 that has a reasonable lean combustion stability is very suitable to an $11{\ell}$ heavy-duty LPG engine with liquid phase fuel injection system. It also has a better mean flow coefficient of 0.34 to develope a stable flame kernel and to produce high performance. This research expects to clarify major factor that effects on the design of intake port efficiently with the optimized swirl ratio for the heavy duty LPG engine.

• 한국연소학회지
• /
• 제20권3호
• /
• pp.13-20
• /
• 2015

The performance of a direct-injection diesel engine often depends on the strength of swirl or squish, the shape of combustion chamber, the number of nozzle holes, etc. This is natural because the combustion in the cylinder was affected by the mixture formation process. Since the available duration to make the mixture formation of air-fuel is very short, it is difficult to make complete mixture. Therefore, an early stage of combustion is violent, which leads to the weakness of noise and vibration. In this paper, the combustion process of a common-rail diesel engine was studied by employing two kinds of pistons. One has several cavities on the piston crown to intensify the squish during the compression stroke in order to improve the atomization of fuel, we call this multi cavity piston in this paper. The other is a toroidal single cavity piston, generally used in high speed diesel engines. To take photographs of flame and flaming duration, a four-stroke diesel engine was remodeled into a two-stroke visible single cylinder engine and a high speed video camera was used.