• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 추계학술대회논문집 - 한국공작기계학회
• /
• pp.349-354
• /
• 2000

A use of Titanium alloy as a structural material is increasing lately. Among those titanium alloys, Ti-6A1-4V alloy is the most popular one with taking 2/3 of it's market. Also, Ti-6A1-4V alloy can get the stability of organization and product measure, and the evaluation of the cutting ability and the mechanical characteristics. The point in titanium alloy work is on how treat the heat generated during grinding. Because the heat conductivity of titanium alloy is unnegligibly low, the grinding heat is accumulated in workpiece, and it cause the increasing of grinding grits' wear and the rough grinding surface. So, these characteristics in grinding of titanium alloy will change the mechanical characteristics of the titanium alloy. From this study, the mechanical characteristics of annealed Ti-6A1-4V alloy after grinding was concerned with checking out the bending strength values, and the factor of the change and the difference was analyzed after analyzing the surface roughness and the image from SEM.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제28권1호
• /
• pp.16-23
• /
• 2002

To understand the micro-mechanical changes and the effects of the fluoride on rat's femur after administration of sodium fluoride, the three-point bending test, acoustic emission analysis during the three-point bending test and scanning electron microscopy were performed. The obtained results were as follows: 1. Bone strength increased in the rats given 1, 5, 10 and 20 ppm of fluoride but, there were no statistical significances (p>0.05). 2. With increasing the concentration of fluoride, most AE events released rapidly just before the maximum load and smaller events were recorded than the control group's. The average of cumulative AE event counts until maximum load of the femur in 20 ppm group were significantly small with respect to the control group's (p<0.05). 3. Fracture surfaces were well coincide with the results of acoustic emission behavior. Analyses of fracture surfaces indicated that, consistent with its the highest load, rat femur in 20 ppm fluoride group displays the roughest surface.

• 공업화학
• /
• 제9권5호
• /
• pp.715-718
• /
• 1998

본 연구에서는 수직섬유의 길이가 서로 다른 삼차원 유리직물을 보강재로 사용하고, 매트릭스 수지로 비스페놀 타입 비닐 에스테르 (bisphenol type vinyl ester)를 사용하여 hand lay-up을 이용해 복합재료 (3D composites)를 제조하였다. 삼차원 유리직물의 수직섬유의 길이가 복합재료의 기계적 물성에 미치는 영향을 three-point bending test, flatwise compression test를 통해 조사하였다. Short-beam test법 통하여 복합재료에서의 섬유와 매트릭스 수지간의 계면접착강도를 나타내는 층간 전단강도를 구하였다. 시험 결과를 통하여 수직섬유의 길이가 복합재료의 기계적 물성 및 층간 전단강도에 많은 영향을 미침을 알 수 있었다.

• Computers and Concrete
• /
• 제32권2호
• /
• pp.173-184
• /
• 2023

In this study, mechanical, flexural post-cracking, and torsional behaviors of recycled steel fiber-reinforced concrete (RSFRC) incorporating steel fibers obtained from recycling of waste tires were investigated. Initially, three concrete mixes with different fiber contents (0, 40, and 80 kg/m³) were designed and tested in fresh and hardened states. Subsequently, the flexural post-cracking behaviors of RSFRCs were assessed by conducting three-point bending tests on notched beams. It was observed that recycled steel fibers improve the post-cracking flexural behavior in terms of energy absorption, ductility, and residual flexural strength. What's more, torsional behaviors of four RSFRC concrete beams with varying reinforcement configurations were investigated. The results indicated that RSFRCs exhibited an improved post-elastic torsional behaviors, both in terms of the torsional capacity and ductility of the beams. Additionally, numerical analyses were performed to capture the behaviors of RSFRCs in flexure and torsion. At first, inverse analyses were carried out on the results of the three-point bending tests to determine the tensile functions of RSFRC specimens. Additionally, the applicability of the obtained RSFRC tensile functions was verified by comparing the results of the conducted experiments to their numerical counterparts. Finally, it is noteworthy that, despite the scatter (i.e., non-uniqueness) in the aspect ratio of recycled steel fiber (as opposed to industrial steel fiber), their inclusion contributed to the improvement of post-cracking flexural and torsional capacities.

• 대한치과보철학회지
• /
• 제41권3호
• /
• pp.288-299
• /
• 2003

Statement of problem: Many kinds of post and core systems are in the market, but there are no clear selection criteria for them. Purpose: The purpose of this study was to compare the flexural strength and modulus of elasticity of core materials, and measure the bending strength of post systems made of a variety of materials. Material and Methods: The flexural strength and elastic modulus of thirteen kinds core buildup materials were measured on beams of specimens of $2.0{\times}2.0{\times}24{\pm}0.1mm$. Ten specimens per group were fabricated and loaded on an lnstron testing machine at a crosshead speed of 0.25mm/min. A test span of 20 mm was used. The failure loads were recorded and flexural strength calculated with the measured dimensions. The elastic modulus was calculated from the slopes of the linear portions of the stress-stram graphs. Also nine kinds commercially available prefabricated posts made of various materials with similar nominal diameters, approximately 1.25mm, were loaded in a three-point bend test until plastic deformation or failure occurred. Ten posts per group were tested and the obtained data were anaylzed with analysis of variance and compared with the Tukey multiple comparison tests. Results: Clearfil Photo Core and Luxacore had flexural strengths approaching amalgam, but its modulus of elasticity was only about 15% of that of amalgam. The strengths of the glass ionomer and resin modified glass ionomer were very low. The heat pressed glass ceramic core had a high elastic modulus but a relatively low flexural strength approximating that of the lower strength composite resin core materials. The stainless steel, zirconia and carbon fiber post exhibited high bending strengths. The glass fiber posts displayed strengths that were approximately half of the higher strength posts. Conclusion: When moderate amounts of coronal tooth structure are to be replaced by a post and core on an anterior tooth, a prefabricated post and high strength, high elastic modulus core may be suitable. CLINICAL IMPLICATIONS In this study several newly introduced post and core systems demonstrated satisfactory physical properties. However when the higher stress situation exists with only a minimal ferrule extension remaining a cast post and core or zirconia post and pressed core are desirable.

• 대한치과기공학회지
• /
• 제19권1호
• /
• pp.37-42
• /
• 1997

The interfacial bond strengh and microstructural analysis of pre-heat treated porcelain-fusedmetal(PFM) were investigated using a mechanical three-point bending tester and scanning electron microscope(SEM). Four kinds of heat treated samples were prepared as follows ; A: Heating $1200^{\circ}F{\to}1600^{\circ}F$, holding 1min, reheating ${\to}1850^{\circ}F$, hold 3min under vacuum, B: heating $1200^{\circ}F{\to}1600^{\circ}F$, holding 1min, reheating${\to}1850^{\circ}F$ under vacuum conditon, C: heating $1200^{\circ}F{\to}1600^{\circ}F$, holding 1min, reheating${\to}1850^{\circ}F$, holding 3min in the air, repeat same heat treatment process under vacuum condition, D: heating $1200^{\circ}F{\to}1600^{\circ}F$, holding 1min, reheating${\to}1850^{\circ}F$, holding 1min in the air. The three-point bening test result shows that the interfacial bond strength of specimen B and C were higher than that of A and D. The SEM study indicate that Specimen C shows the highest surface density.

• 한국해양공학회지
• /
• 제21권6호
• /
• pp.16-25
• /
• 2007

In a companion paper, a rational mechanical model to predict the entire behavior of point-loaded RC slender beams (a/d > 2.5) without shear reinforcement was developed. This paper presents the test results of 9 slender shear beams and compares them with analytical results performed by the proposed model. They are grouped by two parameters, which are shear span ratio and concrete strength. Three kinds of concrete strength the 26.5, 39.2, and 58.8 MPa were included as a major experimental parameter together with different shear span ratios ranging from 3 to 6 depending on the test series. Tests were set up as a traditional 3 point bending test. Various measurements were taken to monitor abrupt shear failure. Test results were not only compared with analytical results from the proposed model, but also other formulas, to consider the various aspects of shear failure such as kinematical conditions or shear capacity. Finally, a review of the proposed model is presented with respect to the shear transfer mechanisms and the effect of test parameters. Results show that several assumptions and proposals adopted in the proposed model are rational and reasonable.

• 대한소아치과학회지
• /
• 제23권2호
• /
• pp.347-355
• /
• 1996

The purpose of this study was to compare the bond strengths of different kinds of glass ionomer cements (GIC), which is recently increasing the clinical application in the field of pediatric dentistry and measure the repaired bond strengths in order to examine the clinical applicabilty of partial repaired cases. By using one kind of the light cured type GIC and three kinds of the chemical cured type GIC, the bond strengths of the followings were compared : unrepaired group as control, repaired conditioning group, which was treated the repaired surface using 25% polyacrylic acid and repaired non-conditioning group without surface treatment. Three point bending test was performed under Universal Testing Machine in order to measure the compressive bond strengths. The results were as follows : 1. Light cured GIC had higher bond strength than chemical cured type GIC in both of repaired and unrepaired groups. 2. In repaired cases, all of the materials decreased the bond strength when compared to the control group. In the light cured type, the bond strength of repaired conditioning group decreased 31.6%, repaired non-conditioning group decreased 40.8%. In chemical cured types, the bond strength of repaired conditining group decreased 11.8%, repaired non-conditioning group decreased 20.9%. 3. All the materials, in the case of the chemical treatment on the repaired surface using 25% polyacrylic acid had higher bond strength than untreated but, lower than control group.

• Korean Chemical Engineering Research
• /
• 제45권5호
• /
• pp.479-486
• /
• 2007

BCB 수지를 이용하여 본딩한 웨이퍼의 BCB 두께, 본딩 촉진제의 사용여부 및 이웃하는 적층 물질의 종류에 따른 본딩 결합력에 대한 영향을 4-점 굽힘방법을 이용하여 규명한다. 실험결과 본딩 결합력은 BCB 두께에 선형 비례하는데, 이는 BCB의 소성 변형의 정도가 두께에 비례하는 반면에 BCB의 항복 강도에는 영향을 미치지 않기 때문이다. 본딩한 BCB의 두께가 각각 $2.6{\mu}m$ 및 $0.4{\mu}m$인 경우에 대하여 본딩 촉진제를 사용 했을 때, 본딩 촉진제와 본딩된 물질의 표면에서는 공유 결합이 형성되기 때문에 본딩 결합력이 증가한다. 산화 규소막이 증착된 실리콘 웨이퍼와 BCB 사이 계면에서의 본딩 결합력은 글래스 웨이퍼와 BCB 사이의 계면에서 보다 약 3배 정도 높다. 이러한 본딩 결합력의 차이는 각 계면에서 Si-O 본드의 본딩 밀도 및 본드 파단 에너지의 차이에 기인한다. PECVD 산화 규소막을 증착한 실리콘 웨이퍼와 BCB 사이 계면의 경우, 기 측정된 $18J/m^2$ 및 $22J/m^2$의 본드 파단 에너지를 얻기 위해 각각 약 $12{\sim}13bonds/nm^2$ 및 $15{\sim}16bonds/nm^2$의 Si-O 본드 밀도가 필요하다. 반면에, 글래스 웨이퍼와 BCB 사이 계면의 경우에는 기 측정된 $5J/m^2$의 본드 파단 에너지를 얻기 위해 약 $7{\sim}8bonds/nm^2$의 Si-O 본드 밀도가 필요하다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제3권2호
• /
• pp.199-204
• /
• 1999

최근에 복합재료는 콘크리트, 집성보와 같은 기존의 구조재를 보강하여 성능을 향상시킬 목적으로 적용되고 있다. 특히, 대규모의 집성보 구조물은 춤이 큰 부재를 필요로 하는데 섬유보강판을 이용하여 보의 상하부를 보강하면 춤을 크게 하지 않고도 보의 강도와 강성을 증가시킬 수 있다. 본 연구에서는 집성보에 유리섬유보강 플라스틱판(GFRP)을 붙여 스팬 중앙에 집중하중을 가한 휨실험을 수행하였고 실험결과를 층간이론을 이용한 수치해석법과 비교하였다.