• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.2
• /
• pp.98-104
• /
• 2012

In this paper, precision processing is carried out for the pre hardened steel(HRC 54), which is one of injection mould materials. Processing characteristics are estimated according to the number of tool cutting blade and roundness is observed by the 3-Dimensional measuring machine. The surface roughness affected by the wire electric discharge machining are measured. Cutting component force of STAVOX is the highest in condition of 2F processing because load per a blade of cutting tool is high. Especially, the difference in Fz is over 20N by cutting load. The slower spindle rotation speed and tool feed rate are, the better cutting component force is. The roundness of hole processed in condition of 4F is good because feed rate is able to be fast. When rotation speed is increased, the surface roughness is decreased. The surface roughness acquired in condition of 2F processing is higher about 50% than 4F processing.

• Economic and Environmental Geology
• /
• v.33 no.4
• /
• pp.309-320
• /
• 2000

Aperture is an important parameter for determining the hydraulic characteristics of fractured media. In this study the topography of artificial rock joint surface was measured using 3D laser profilometer to analyze the aperture distribution. The initial aperture distribution was determined when the contact area became one percent of total joint surface. The initial aperture distribution of granite joint, with the mean value of 0.78 mm and the standard deviation of 0.34 mm was much different from that of the marble joint, with the mean value of 0.57 mm and the standard deviation of 0.26 mm. Apertures of both granite and marble showed normal distributions. Aperture distribution with the contact area of 25% was also analyzed. Mean value was decreased to one third compared to the initial aperture, but the standard deviation was decreased slightly. To determine the spatial correlation of the aperture distribution variogram analysis was carried out on the initial aperture data. Most experimental variograms were fitted well with exponential model. It is expected that the measured aperture characteristics can be used for stochastic analysis of fluid flow through rock joints.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.6
• /
• pp.64-71
• /
• 1995

The objective of this paper is to realize an analysis system that is capable of controlling the quality of an entire cutting process by including a 3 coordinate measuring machine in the process line. Fuzzy reasoning networks based on fuzzy associative memories has been intro- duced in the measuring process, the control limits for the control process have been obtained, and the efficiency and reliability of the system have been determined by examining the simu- lated reasoning control values.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.12 no.3
• /
• pp.51-58
• /
• 1998

This paper deals with the power frequency electric and magnetic profiles from transformer and gas-insulated swichgear(GIS) perimeters in the indoor power substation. Measurements of electric and magnetic field magnitudes were carried out by using single axis and three axes field meters at a height of 1[m]. The resultant electric and magnetic field profiles measured in the vicinity of the transformer were displayed as a 2-dimensional plot. The electric fields intensity are relatively low value of about 2.3~9[V/m], and the magnetic fields intensity range from 0.3 to [$20.3\mu$T]. Also, in the GIS perimeter the electric fields intensity are in the range of 2.2~2.5[V/m], and the high magnetic fields are largely localized to the intermediate section of the GIS and their amplitudes are [$1.2~39.5\mu$T]. Metal enclosures of transform and GIS play a role in reducing the electric field, and the magnetic fields are characterized by a rapid decrease with distance from the transformer and GIS enclosures.

• Proceedings of the Optical Society of Korea Conference
• /
• 2007.07a
• /
• pp.243-244
• /
• 2007

본 연구에서는 성형용 코어 가공에서 초경합금(WC, Co 0.5%)의 초정밀 가공특성을 파악하기 위하여 다이아몬드 휠의 메시, 주축 회전속도, 터빈 회전속도, 이송속도 및 연삭깊이에 따른 표면거칠기를 측정하여 최적연삭조건을 규명하였다. 규명된 최적연삭가공조건을 활용하여 페러렐 연삭법으로 초정밀 연삭가공을 수행하였다. 연삭가공은 초정밀가공기(ASP01, Nachi-Fujikoshi Co., Japan)를 사용하였다. 최종 정삭가공을 수행한 비구면 성형용 코어의 형상측정결과 형상정도(PV; ${\varphi}$ 3.0mm) 0.15${\mu}m$(비구면), 0.10${\mu}m$(평면)으로 3M급 이상의 고화질 카메라폰에 채용되고 있는 비구면 Glass렌즈 양산용 성형용 코어 규격에 만족한 결과로서 본 연구에 수행된 초정밀 가공조건 및 측정방법이 매우 유효함을 알 수 있었다. 형상정도(PV) 및 표면조도(Ra) 측정은 초정밀 자유곡면 측정기(UA3P, Panasonic Co., Japan)와 3차원 표면조도 측정기(NewView5000, Zygo Co., USA)를 각각 사용하였다. 초정밀 가공된 성형용 코어면에 이온증착법을 활용하여 DLC 코팅을 수행하였다. 코팅 전후의 성형용코어를 활용하여 Glass소재(K-BK7, Sumita Co., Japan)를 최적의 성형조건(성형온도, 압력, 냉각속도)으로 성형하였다. DLC 코팅과 성형은 DLC 코팅기(NC400, Nanotech Co., Japan)와 Glass렌즈 성형기(Nano Press-S, Sumitomo Co., Japan)을 각각 사용하였다. Fig. 1은 초정밀 연삭가공, DLC 코팅막 구조, 코팅된 성형용 코어, 그리고, 성형된 비구면Glass렌즈를 각각 나타낸다.

• KIPS Transactions on Software and Data Engineering
• /
• v.4 no.4
• /
• pp.177-186
• /
• 2015

For data fusion of laser range finder (LRF) and vision camera, accurate calibration of external parameters which describe relative pose between two sensors is necessary. This paper proposes a new calibration method which can acquires more accurate external parameters between a LRF and a vision camera compared to other existing methods. The main motivation of the proposed method is that any corner data of a known 3D structure which is acquired by the LRF should be projected on a straight line in the camera image. To satisfy such constraint, we propose a 3D geometric model and a numerical solution to minimize the energy function of the model. In addition, we describe the implementation steps of the data acquisition of LRF and camera images which are necessary in accurate calibration results. In the experiment results, it is shown that the performance of the proposed method are better in terms of accuracy compared to other conventional methods.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.8
• /
• pp.2081-2087
• /
• 1994

Touch trigger probes are widely used for inspection purposed in the CMM(Coordinate meauring machine) or machine tool. The errors introduced by measurement probe are fairy systematic, thus can be calibrated and compensated properly. This paper presents a technique for the error calibration and compensation of the probe errors, which can be easily applicable to the manufacturers and users of the measurement probe. The probe coordinate system is defined for the probe error assessment, and a reference sphere ball is measured, and the probe errors are calibrated. The calibrated probe errors are represented in the 3D error map and 2D error map along probing direction. Detail algorithms for the error compensation are proposed.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.5
• /
• pp.58-64
• /
• 2000

This paper proposes a method for determining optimal EDM parameters based on discharge area from the physical model of a tool electrode. Main parameters, which affect the EDM performance, are peak value of currents, pulse-on time, and pulse-off time. Such parameters are closely dependent on the discharge area in EDM process. In this paper the discharge area is estimated from the CMM scanning data to the tool electrode. The method is very useful when any geometric information to the tool electrode is not provided from tool modeler or producer. The method consists of following four steps. First a triangulation mesh is constructed from the CMM data. Secondly, the z-map is modeled from the triangulated mesh. Thirdly, the discharge area is estimated from intersection between the z-map model and a z-height plane. Finally, the machining parameters are easily calculated by some known EDM equations to the discharge area. An example is introduced to show that the machining parameters are calculated from the CMM data to a tool electrode.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.04a
• /
• pp.179-184
• /
• 2003

Noise cause is dividing to fluid noise by exhaust flow of fm and vibration noise by rotational vibration of motor. Until now, measuring method has been used to measure vibration by the accelerometer, this method has been not measured for the vibration in some parts of brush and commutator because of motor construction. This research was purposed on the accurate analysis, using laser vibration analyzer, of noise cause against the difficult part in old times. By using this measured data, we would like to use for the design of silent motor.

• IE interfaces
• /
• v.12 no.2
• /
• pp.180-192
• /
• 1999

A coordinate measuring machine (CMM) is a computer-controlled measuring device that uses a probe to obtain measurements on a manufactured part's surface. CMM's have been very popular over traditional hard gauges due to their flexibility, accuracy, and ease of automated inspection. This paper considers the use of a CMM for the inspection of gears. We compare the inspection capability of a CMM and that of a gear-specific measuring machine. The result of this paper may benefit gear manufacturing companies in their dimensional quality assurance activities, especially for special type gears and for large-scale gears which are not measurable by gear-specific measuring machines.