• Composites Research
• /
• v.15 no.1
• /
• pp.41-52
• /
• 2002

This paper presents the thermo-elastic analysis for searching the behavior of carbon/carbon brake system during the braking period and the 3-D stress analysis to find the shape of the brake disk which is safe to the failure. The mechanical properties of the carbon/carbon brake disk were measured for both in-plane and out of plane directions. The mechanical properties were used as the input of the thermo-elastic analysis and 3-dimensional stress analysis for the brake disk. The gap between rotor clip and clip retainer is an important parameter in the loading transfer mechanism of the rotor disk. The change of gap was considered both the mechanical deformation and thermal deformation. Because the rotor clip and clip retainers were not contacted, they were excluded from the analysis model. Rotor disk was modeled by using the cyclic symmetry condition. The contact problems between rotor clip and key drum as well as between rotor disk and rotor were considered. From the results of the 3-D stress analysis, the stress concentration at the key hole of the brake disk was confirmed. The stress distributions were studied thor the variation of the rotation angle of the contact surface and the radius of curvature at the key hole part.

• Journal of Korea Water Resources Association
• /
• v.36 no.5
• /
• pp.761-776
• /
• 2003

Numerical models were employed to investigate the hydrodynamics of water flow in the lake behind a dam and the spillway where supercritical flows and negative pressures are likely to occur. In this study, 2-D model, RMA2 was employed to examine the upstream flow pattern and 3-D CFD model, FLUENT was used to evaluate the three-dimensional flow in the approaching region and flow distributions in the spillways and discharge culverts. The bathymetry and the details of structures were carefully taken into consideration in building the models. The results from applying the 2-D model for the planned Hantan River Dam show that large eddies, the velocity of which reaches up to 1 m/s are occurring in several places upstream of the dam. That means that the 2-D numerical model could be utilized to investigate the two-dimensional flow patterns after the construction of a dam. Three-dimensional numerical results show that the approach flow varies depending on stages and discharge conditions, and velocities at spillways, discharge culverts, and sediment flushing tunnels are differently distributed. The velocity distributions obtained from the numerical model and a hydraulic model at the centerline of spillways 100 m upstream of the dam show reasonably similar results. It is expected that 2-D and 3-D numerical models ate useful tools to help optimize the dam design through investigating the flow patterns in the spillway and at the upstream of the dam, which is not always feasible in hydraulic modeling.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.3
• /
• pp.411-418
• /
• 1992

본 연구에서는 인장하중을 받는 균열이 없는 박판 시험편과 45˚경사균열시험 편의 고유진동수 측정을 위하여 레이저 홀로그래피법을 이용하여 진동모드 측정을 하 여 그 결과를 비교분석하는 실험방법을 택하였으며, 균열이 없는 박판에 대해서만 무 차원하중의 증가에 따른 고유 진동수의 변화관계를 실험치와 Ritz Method에 의한 유한 요소 해석치와 비교하였다.

• Electronics and Telecommunications Trends
• /
• v.15 no.5 s.65
• /
• pp.86-93
• /
• 2000

지하 탐사용 레이더를 이용하여 지하에 매설된 구조물의 위치를 파악하고 그에 따른 근사 이미지의 추출 방법을 제안하였다. 기본원리는 구조물에 의해 산란되어 수신 안테나로 유입되는 펄스신호의 지연시간과 크기를 측정하는 데 있으며, 측정의 실용성을 위하여 레이더 탐색경로에 따른 수신신호의 절대치 적분 방법을 사용하였다. 일반적으로 지하매질은 침투 주파수에 따라서 다양한 분산 및 손실 특성을 나타내는데, 이러한 매질 특성은 다항 Debye 모델을 이용하여 기술되었다. 3차원 전파(電波) 전파(傳播)를 위한 시뮬레이션에는 FDTD(Finite Difference Time Domain) 방법을 사용하였다.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.49 no.1
• /
• pp.1-7
• /
• 2012

This paper presents a method for 3D image construction using the hybrid (color and depth) camera system, in which the drawbacks of each camera can be compensated for. Prior to an image generation, intrinsic parameters and extrinsic parameters of each camera are extracted through experiments. The geometry between two cameras is established with theses parameters so as to match the color and depth images. After the preprocessing step, the relation between depth information and distance is derived experimentally as a simple linear function, and 3D image is constructed by coordinate transformations of the matched images. The present scheme has been realized using the Microsoft hybrid camera system named Kinect, and experimental results of 3D image and the distance measurements are given to evaluate the method.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.25 no.9
• /
• pp.1571-1582
• /
• 2001

한국 전통 의상인 한복 치마의 형태는 천의 특성에 크게 좌우된다. 이에 본 연구에서는 직물의 물성과 착장시 한복 치마 형태의 관계를 규명하고자, 8가지 직물을 선택하여 물성을 측정하고, 비접촉 3차원 인체계측시스템을 이용하여 , 치마 착장시의 5개 수평단면, 2개 수직단면을 작성하였다. 수직 단면에서는 실루엣을 나타내는 각도, 수평단면에서는 단면의 부피감과 드레이프의 형태를 나타내는 노드 간격, 거리, 각도를 측정하였다. 첫째, 경연도, 신장률, 실 두께, 직물 무게의 직물물성요인에 따라 실험 직물은 4집단으로 분류되었다. 둘째, 직물의 물성과 노드의 형태의 관계를 살펴본 결과, 직물이 뻣뻣하고 가벼울수록, 치마윗부분의 각도가 커지며 , 부드럽고, 신축성 이 있고, 무겁고, 두꺼운 실로 짜여지면, 튜블러 형태 의 실루엣을 나타내었다. 셋째 , 수직 단면도상 치마 위쪽과 아래쪽의 퍼짐각도 및 수평단면상의 둘레, 노드간의 거리, 가장 긴 파고와 같은 단면 계측치는 직물물성에 따라 추정 이 가능한 것으로 나타났다.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.24 no.2
• /
• pp.203-211
• /
• 2008

Minimizing damage to anatomical structure is a prerequisite for skeletal anchorage system to install a miniscrew. This research has focused on evaluating the stability and safety of installation in the maxillary molar buccal area, in which most miniscrews are installed clinically and initial fixation is weak. CT (computerized tomography)images were taken for surveying the possibility of damaging to adjucent teeth in accordance with installation angle. If we install a mini-screw($1.2{\times}6.0mm$) in the maxillary molar buccal area, it would be located generally in the 5~8mm upper of CEJ and 3~5mm inner of the cortical bone surface. We has measured the space between roots And comparison has been made for gender and the space between roots in accordance with the 3 different angles of installation(30 degree, 40 degree, 60 degree) in 3 categories. Category 1 : between 1st molar and 2nd molar Category 2 : between 1st molar and 2nd premolar Category 3 : between 1st premolar and 2nd premolar The result are as follow; 1. The space for category 1 was significantly small. 2. For the installation angle, it was safer to install with steeper angle in category 1 and category 2, but not in category 3. According to these results, the installation a miniscrew in category 2, 3 is safer than in category 1. And it is safer to install with steeper angle in category 1 and category 2.

• Food Science and Preservation
• /
• v.17 no.1
• /
• pp.16-22
• /
• 2010

To maintain the storage quality of agricultural products, temperature uniformity during cold storage, which is affected by fan flow rate and product arrangement, is important. We simulated and validated a CFD (Computational Fluid Dynamics) model that can predict both airflow and temperature distribution in a cold storage environment. Computations were based on a commercial code (FLUENT 6.2) and two turbulence models. The standard k-$\varepsilon$ model and the Reynolds stress model (RSM) were chosen to improve the accuracy of CFD prediction. To obtain comparative data, the temperature distribution and velocity vector profiles were measured in a full-scale cold storage facility and in a 1/5 scale model. The agricultural products domain in cold storage was modeled as porous for economical computation. The RSM prediction showed good agreement with experimental data. In addition, temperature distribution was simulated in the cold storage rooms to estimate the uniformity of temperature distribution using the validated model.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.48 no.6
• /
• pp.15-23
• /
• 2011

Stereo vision approach to solve the problem using a single camera three dimension precise distance measurement and object recognition method is proposed. Precise three dimensional information of objects can be obtained using single camera, a laser light and a rotating flat mirror. With a simple thresholding operation on the depth information, the segmentations of objects can be obtained. Comparing the signatures of object boundaries with database, objects can be recognized. Improving the simulation results for the object recognition by precise distance measurement are presented.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.35 no.2
• /
• pp.297-304
• /
• 2008

The purpose of this study was to evaluate a 3-Dimensional laser scanner for the space analysis after loss of a primary first molar. Six children with premature loss of a primary first molar were examined using study models taken before and after the extraction. The results were as follows: 1. There was no change in primary molar space after the extraction of a maxillary primary first molar However, 2 out of 3 children experienced primary molar space loss in extraction side of a mandibular primary first molar. 2. Arch width and arch perimeter showed no difference between initial and final model. 3. All primary canines did not show any changes in inclination. Maxillary primary second molars had similar changes in both extraction and control side. However, 2 out of 3 mandibular primary second molars in extraction side showed more lingual tipping compared to control side. Mandibular permanent first molars tipped more lingually in extraction side. 4. In angulation, primary canines showed nothing of significance. Mandibular primary second molars tipped more mesially in extraction side than in control side. Maxillary permanent first molars have increased distal angulation after extraction of primary first molars in both side.