• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.5
• /
• pp.505-511
• /
• 2016

The aim of this study is to investigate the thermoforming characteristics of an inner case with three refrigerator cavities using three-dimensional(3D) thermoforming analyses. We perform fundamental formability analyses using a 3D model of the mould for the inner case. We carry out tensile tests at the elevated temperature to examine the properties and characteristics of the thermoformed material. Then, we design sub-processes of the thermoforming process for the inner case. In addition, we develop suitable finite-element models for different sub-processes. We investigate the deformed shapes and thickness distributions of the inner case for different sub-processes using the results of the thermoforming analysis. Finally, we discuss the formability and thermoforming characteristics of the inner case with three cavities.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.16 no.1
• /
• pp.9-13
• /
• 1979

Multimode characteristics of a dielectrically loaded rectangular cavity are analyzed by a graphical method. Coupled transcendental equations for multimode frequencies may be solved graphlially. This shows that the resonant frequencies of the partially flued cavity with a dielectic are shifted toward lower frequencies compared to those of the empty cavity. It is shown that a perturbational scheme can not be employed to calculate multimode frequencies because of relatively large frequency shrift. Existence of the surface wave modes In the dielectric and their resonant frequencies are early predicted from this graphical method.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.7
• /
• pp.771-777
• /
• 2014

Injection-compression molding was used for film insert molding of an automotive door grip using films with three-dimensional embossed patterns. A vacuum mold was fabricated for vacuum-assisted thermoforming of the film, and an injection-compression mold was developed for film insert molding. Three pressure transducers were installed inside the mold cavity to measure cavity pressures. Injection-compression molding experiments under various compression strokes and toggle speeds were performed to investigate their effects on the cavity pressure and heights of the embossed patterns. The compression stroke of 0.9mm and low toggle speed resulted in a higher degree of conservation of embossed patterns. Additionally, the processing conditions for the maximum heights of embossed patterns were almost similar to those for minimum integral value of cavity pressures. The injection-compression molding process presents the opportunity to impart a soft-touch feeling of plastic parts printed with embossed patterns.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.12
• /
• pp.89-94
• /
• 2012

In this paper, a UHF cavity-backed spiral antenna for partial discharge diagnosis is proposed. The proposed antenna consists of two-arm Archimedean spiral, a cavity, and a balun for feeding. The spiral antenna is designed for 0.3-1.5 GHz operating frequency. Two spiral arms of the proposed antenna are fed by a microstrip tapered-balun. In order to enhance the gain, the cavity is located in the back side of the spiral pattern. The proposed antenna is designed and simulated using CST Microwave Studio. The designed antenna is also fabricated and tested to validate performance. The measured radiation patterns are directional to the +z-axis and measured peak gain is 9.92 dBi.

• The Korean Journal of Rheology
• /
• v.10 no.4
• /
• pp.217-226
• /
• 1998

The anisotropy caused by the fiber orientation, which is inevitably generated by the flow during injection molding of short fiber reinforced polymers, greatly influences dimensional accuracy, mechanical properties, and other quality of the final product. Since the filling stage of the injection molding process plays a vital role in determining fiber orientation, an accurate analysis of flow field for the filling stage is needed. Unbalanced filling occurs when a complex or a multi-cavity mold is used leading to development of regions where the fiber suspension is under compression. It is impossible to make an accurate calculation of the flow field during filling with the analysis assuming incompressible fluid. A mold with four cavities with different filling times was produced to compare the numerical analysis results with the experimental data. There was a good agreement between the experimental and theoretical results when the compressibility of the polymer melt was considered for the numerical simulation. The fiber orientation states for compressible and incompressible fluids were also compared qualitatively as well as quantitatively in this study.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.26 no.3
• /
• pp.29-40
• /
• 1989

A new blade section of propeller is developed to obtain higher propeller efficiency and better cavitation performance. Eleven foil sections are carefully designed and manufactured to compare the lift-drag characteristics and cavitation performances. It is expected that the developed section behaves better in the vicinity of the ship's wake, where the angle of attack variation is large, because of its wider width in lift-drag and cavitation-free bucket diagrams. A propeller design method using the selected foil section is presented. Three chordwise loading shapes are selected to investigate the influence of the lift-drag ratios on the propeller efficiencies and cavitation performances. Three propellers are designed, which correspond to the selected chordwise loading shapes. Two more propellers which use existing foil sections are designed to compare the section performance.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.1
• /
• pp.39-46
• /
• 2013

This study aims to develop a plastic aspheric lens for a 13-megapixel mobile phone camera by injection-compression molding. A mold for injection-compression molding experiments was fabricated with a movable upper plate and four springs. During cavity filling for an aspheric lens with a thickness ratio of 2, a weldline was formed under conventional injection molding, whereas no weldline was formed under injection-compression molding with a compression stroke of 0.3 mm. The flow patterns were in good agreement with the simulation results. The birefringence decreased as the compression stroke increased, and the birefringence produced by injection-compression molding was very low and more uniform compared with that produced by injection molding. In addition, the bulk birefringence of an assembly composed of four plastic lenses was significantly affected by the orientation of the lenses to be mounted.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.6
• /
• pp.483-488
• /
• 2020

In recent years, the demand for wireless devices incorporating several wireless communication systems into one has been increasing in order to provide services that meet the diverse needs of consumers. Wireless devices consisting of various wireless communication systems require many frequency fixed filters. A frequency tunable filter can replace a number of frequency fixed filters in the wireless devices. If a frequency tunable filter is used in wireless systems, the system can be configured more efficiently. In this paper, a 3-pole frequency tunable BPF(bandpass filter) operating in the frequency band of 800 ~ 2400MHz is designed. In order to widen the operating frequency band, a tuning screw is designed to have a step and a linear motor is used to facilitate the adjustment of the tuning screw. The implemented frequency tunable BPF operates in the designed frequency range and has the maximum insertion loss of 2.82dB in the channel band and the minimum attenuation of 18.7dB at ± 50MHz frequency offset from the center frequency of the band.

• 전기의세계
• /
• v.27 no.5
• /
• pp.33-54
• /
• 1978

(차례) 1.산학협동심포지업 (1)우리나라에서의 연구개발과 산학협동 (2)산학협동과 산업계의 역할 (3)산학협동의 현황과 진로 2.학술회의A (1)전력게통의 계층구조와 협조원리에 관한 연구 (2)2중층괴상회전자 유도전동기의 이론해석 (3)초고주파가열장치에 사용하는 철공진변압기의 해석적 설계 (4)한국전기기시험연구소 대전력단락 시험설비설계 (5)직류전동기제어를 위한 Thyristor Chopper정류회로에 관한 연구 (6)선로의 개폐정보를 포함하는 전력계통의 상태추정 (7)단일신경세포에 대한 ITEM 신호 특성 3.학술회의B (1)MMM-1 Computer System의 설계 및 제작 (2)Adaptive Delta Modulation System의 성능비교 연구 (3)6GHZ FMD마이크로파 무선전송장치의 개발 (4)적선도에 의한 회로망함수의 결정 (5)동맥혈압의 해석과 그의 전기적 유사모델 (6)피부감각의 정보전달 특성에 관하여 (7)선형직접회로의 공정설계 및 그 특성 조성 (8)DH L.D의 전기적포화현상에 관한 이론적 해석 (9)Potocoupler를 이용한 Isolator 4.학술회의C (1)Al-Al$_{2}$O$_{3}$ -Al박막구조의 전기적 특성 (2)이종금속에 샌드위치된 고분자물질의 단락전조 (3)유전체가 일부체워진 직 6면체의 캐비티의 다중모오드 해석 (4)반도체 가스 검지소자의 제조 및 그의 전기적 특성 (5)실리콘 산화공정에 대한 실험적 고찰 (6)진공증착법에 의한 InSb 박막제도에서 열처리효과 (7)(Ba$_{1}$-xBix) Tio$_{3}$ PTC thermistor의 첨가량의 최적건안 (8)금속박막증착시 두께조절 5.특별강연회 (1)일본에 있어서의 절력계통공학연구 (2)Linear Motor의 최근개발동향량도 높았다. valine과 leucine 및 aspartic acid, glycine과 glutamic acid, leucine과 aspartic acid 간에는 고도의 정상관, glycine과 serine, valine과 phenylalanine, threonine과 proline, phenylalanine과 arginine, methionine과 glutamic acid, histidine과 lysine 간에는 유의 정상관, 그리고 isoleucine과 lysine 간에는 유의한 부상관이 있었다. 4. lysine 함량은 단백질 함량과 정산곤, isoleucine 함량은 단빅질 함량과 부상관을 보였으며, alanine, valine, leucine 함량은 지방함량과 각각 유의한 정산관을 보였다. 5. 대두 단백질은 7.5% acrylamide gel 전기영동에 의해 품종에 따라 12～16개의 구성분으로 분리되었으며, 이들중 주구성분들은 상대이동도가 0.06(a), 0.14(b). 0.24(d) 이었고, 구성분 b의 함량이 품종간에 가장 변이가 컸으며, 구성분 b는 그밖의 주요 구성분들의 함량과 부의 상관이 있었고, 구성분 a는 단백질 함량과 정상관이 있었다. 6. 종실단백질 구성분들의 조합 특성 면에서 공시 86품종은 11개 유형군으로 분류되었으며, 우리나라와 일본품종은 미국품종에 비해 단백질구성분 조성이 훨씬 다양하였다. 7. 이동도가 매우 빠른 단백질 구성분 o(Rm 0.77) p(Rm 0.81)를 모두 갖고 있는 품종은 3품종, 모두 갖고 있지 않은 품종은 1품종이었고, 나머지 82품종은 o나 p중 한 구성분을 갖고 있었으며 그 분포율은 30 : 65 이었는데 미국계 품종은 우리나라 품종에 비해 구성분 o를 간고 있는 비율이 현저히 적었다. 8. 대두 종실은 개화후 22일까지 완만히, 그 이후 20～30일간 급속히